Merge branch 'viafb-next' of git://github.com/schandinat/linux-2.6

* 'viafb-next' of git://github.com/schandinat/linux-2.6: (29 commits)
  viafb: add initial VX900 support
  viafb: fix hardware acceleration for suspend & resume
  viafb: make suspend and resume work (on all machines?)
  viafb: restore display on resume
  Minimal support for viafb suspend/resume
  viafb: use proper register for colour when doing fill ops
  viafb: add documentation for proc interface
  viafb: rename output devices
  viafb: add a mapping of supported output devices
  viafb: set sync polarity for all output devices
  viafb: add function to change sync polarity per device
  viafb: reduce I2C timeout and delay
  viafb: enable I2C for CRT
  viafb: fix i2c_transfer error handling
  viafb: vt1636 cleanup
  viafb: introduce per output device power management
  viafb: limit LCD code impact
  viafb: add interface for output device configuration
  viafb: merge the remaining output path with enable functions
  viafb: use new device routing
  ...

Documentation/fb/viafb.txt

@@ -197,6 +197,54 @@ Notes:
        example,
            # fbset -depth 16
 
+
+[Configure viafb via /proc]
+---------------------------
+    The following files exist in /proc/viafb
+
+    supported_output_devices
+
+        This read-only file contains a full ',' seperated list containing all
+        output devices that could be available on your platform. It is likely
+        that not all of those have a connector on your hardware but it should
+        provide a good starting point to figure out which of those names match
+        a real connector.
+        Example:
+        # cat /proc/viafb/supported_output_devices
+
+    iga1/output_devices
+    iga2/output_devices
+
+        These two files are readable and writable. iga1 and iga2 are the two
+        independent units that produce the screen image. Those images can be
+        forwarded to one or more output devices. Reading those files is a way
+        to query which output devices are currently used by an iga.
+        Example:
+        # cat /proc/viafb/iga1/output_devices
+        If there are no output devices printed the output of this iga is lost.
+        This can happen for example if only one (the other) iga is used.
+        Writing to these files allows adjusting the output devices during
+        runtime. One can add new devices, remove existing ones or switch
+        between igas. Essentially you can write a ',' seperated list of device
+        names (or a single one) in the same format as the output to those
+        files. You can add a '+' or '-' as a prefix allowing simple addition
+        and removal of devices. So a prefix '+' adds the devices from your list
+        to the already existing ones, '-' removes the listed devices from the
+        existing ones and if no prefix is given it replaces all existing ones
+        with the listed ones. If you remove devices they are expected to turn
+        off. If you add devices that are already part of the other iga they are
+        removed there and added to the new one.
+        Examples:
+        Add CRT as output device to iga1
+        # echo +CRT > /proc/viafb/iga1/output_devices
+
+        Remove (turn off) DVP1 and LVDS1 as output devices of iga2
+        # echo -DVP1,LVDS1 > /proc/viafb/iga2/output_devices
+
+        Replace all iga1 output devices by CRT
+        # echo CRT > /proc/viafb/iga1/output_devices
+
+
 [Bootup with viafb]:
 --------------------
     Add the following line to your grub.conf:

drivers/video/via/Makefile

@@ -5,5 +5,5 @@
 obj-$(CONFIG_FB_VIA) += viafb.o
 
 viafb-y	:=viafbdev.o hw.o via_i2c.o dvi.o lcd.o ioctl.o accel.o \
-	via_utility.o vt1636.o global.o tblDPASetting.o viamode.o tbl1636.o \
+	via_utility.o vt1636.o global.o tblDPASetting.o viamode.o \
 	via-core.o via-gpio.o via_modesetting.o

drivers/video/via/accel.c

@@ -283,11 +283,12 @@ static int hw_bitblt_2(void __iomem *engine, u8 op, u32 width, u32 height,
 		writel(tmp, engine + 0x1C);
 	}
 
-	if (op != VIA_BITBLT_COLOR)
+	if (op == VIA_BITBLT_FILL) {
+		writel(fg_color, engine + 0x58);
+	} else if (op == VIA_BITBLT_MONO) {
 		writel(fg_color, engine + 0x4C);
-
-	if (op == VIA_BITBLT_MONO)
 		writel(bg_color, engine + 0x50);
+	}
 
 	if (op == VIA_BITBLT_FILL)
 		ge_cmd |= fill_rop << 24 | 0x00002000 | 0x00000001;
@@ -314,13 +315,11 @@ static int hw_bitblt_2(void __iomem *engine, u8 op, u32 width, u32 height,
 	return 0;
 }
 
-int viafb_init_engine(struct fb_info *info)
+int viafb_setup_engine(struct fb_info *info)
 {
 	struct viafb_par *viapar = info->par;
 	void __iomem *engine;
-	int highest_reg, i;
-	u32 vq_start_addr, vq_end_addr, vq_start_low, vq_end_low, vq_high,
-		vq_len, chip_name = viapar->shared->chip_info.gfx_chip_name;
+	u32 chip_name = viapar->shared->chip_info.gfx_chip_name;
 
 	engine = viapar->shared->vdev->engine_mmio;
 	if (!engine) {
@@ -329,18 +328,6 @@ int viafb_init_engine(struct fb_info *info)
 		return -ENOMEM;
 	}
 
-	/* Initialize registers to reset the 2D engine */
-	switch (viapar->shared->chip_info.twod_engine) {
-	case VIA_2D_ENG_M1:
-		highest_reg = 0x5c;
-		break;
-	default:
-		highest_reg = 0x40;
-		break;
-	}
-	for (i = 0; i <= highest_reg; i += 4)
-		writel(0x0, engine + i);
-
 	switch (chip_name) {
 	case UNICHROME_CLE266:
 	case UNICHROME_K400:
@@ -356,6 +343,7 @@ int viafb_init_engine(struct fb_info *info)
 		break;
 	case UNICHROME_VX800:
 	case UNICHROME_VX855:
+	case UNICHROME_VX900:
 		viapar->shared->hw_bitblt = hw_bitblt_2;
 		break;
 	default:
@@ -386,12 +374,36 @@ int viafb_init_engine(struct fb_info *info)
 	viapar->shared->vdev->camera_fbmem_offset = viapar->fbmem_free;
 #endif
 
+	viafb_reset_engine(viapar);
+	return 0;
+}
+
+void viafb_reset_engine(struct viafb_par *viapar)
+{
+	void __iomem *engine = viapar->shared->vdev->engine_mmio;
+	int highest_reg, i;
+	u32 vq_start_addr, vq_end_addr, vq_start_low, vq_end_low, vq_high,
+		vq_len, chip_name = viapar->shared->chip_info.gfx_chip_name;
+
+	/* Initialize registers to reset the 2D engine */
+	switch (viapar->shared->chip_info.twod_engine) {
+	case VIA_2D_ENG_M1:
+		highest_reg = 0x5c;
+		break;
+	default:
+		highest_reg = 0x40;
+		break;
+	}
+	for (i = 0; i <= highest_reg; i += 4)
+		writel(0x0, engine + i);
+
 	/* Init AGP and VQ regs */
 	switch (chip_name) {
 	case UNICHROME_K8M890:
 	case UNICHROME_P4M900:
 	case UNICHROME_VX800:
 	case UNICHROME_VX855:
+	case UNICHROME_VX900:
 		writel(0x00100000, engine + VIA_REG_CR_TRANSET);
 		writel(0x680A0000, engine + VIA_REG_CR_TRANSPACE);
 		writel(0x02000000, engine + VIA_REG_CR_TRANSPACE);
@@ -428,6 +440,7 @@ int viafb_init_engine(struct fb_info *info)
 	case UNICHROME_P4M900:
 	case UNICHROME_VX800:
 	case UNICHROME_VX855:
+	case UNICHROME_VX900:
 		vq_start_low |= 0x20000000;
 		vq_end_low |= 0x20000000;
 		vq_high |= 0x20000000;
@@ -473,7 +486,7 @@ int viafb_init_engine(struct fb_info *info)
 	writel(0x0, engine + VIA_REG_CURSOR_ORG);
 	writel(0x0, engine + VIA_REG_CURSOR_BG);
 	writel(0x0, engine + VIA_REG_CURSOR_FG);
-	return 0;
+	return;
 }
 
 void viafb_show_hw_cursor(struct fb_info *info, int Status)

drivers/video/via/accel.h

@@ -203,7 +203,8 @@
 #define VIA_BITBLT_MONO		2
 #define VIA_BITBLT_FILL		3
 
-int viafb_init_engine(struct fb_info *info);
+int viafb_setup_engine(struct fb_info *info);
+void viafb_reset_engine(struct viafb_par *viapar);
 void viafb_show_hw_cursor(struct fb_info *info, int Status);
 void viafb_wait_engine_idle(struct fb_info *info);
 

drivers/video/via/chip.h

@@ -71,6 +71,9 @@
 #define     UNICHROME_VX855         12
 #define     UNICHROME_VX855_DID     0x5122
 
+#define     UNICHROME_VX900         13
+#define     UNICHROME_VX900_DID     0x7122
+
 /**************************************************/
 /* Definition TMDS Trasmitter Information         */
 /**************************************************/