Merge tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kern…

…el/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "This is the bulk of pin control changes, nothing too exciting about
  this.

  Some changes hit arch/sh and arch/arm but are well isolated and
  acknowledged by the respective arch maintainers.

  Core changes:

   - Dropped the chained IRQ setup callback into GPIOLIB as we got rid
     of the last users of that in this changeset.

  New drivers:

   - New driver for Ingenic X1830.

   - New driver for Freescale i.MX8MP.

  Driver enhancements:

   - Fix all remaining Intel drivers to pass their IRQ chips along with
     the GPIO chips.

   - Intel Baytrail allocates its irqchip dynamically.

   - Intel Lynxpoint is thoroughly rewritten and modernized.

   - Aspeed AST2600 pin muxing and configuration is much improved.

   - Qualcomm SC7180 functions are updated and wakeup interrupt map is
     provided.

   - A whole slew of Renesas SH-PFC cleanups and improvements.

   - Fix up the Intel DT bindings to use the generic YAML DT bindings
     schema (a first user of this)"

* tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
  pinctrl: madera: Remove extra blank line
  pinctrl: qcom: Don't lock around irq_set_irq_wake()
  pinctrl: mvebu: armada-37xx: use use platform api
  gpio: Drop the chained IRQ handler assign function
  pinctrl: freescale: Add i.MX8MP pinctrl driver support
  dt-bindings: imx: Add pinctrl binding doc for i.MX8MP
  pinctrl: tigerlake: Tiger Lake uses _HID enumeration
  pinctrl: sunrisepoint: Add Coffee Lake-S ACPI ID
  pinctrl: iproc: Use platform_get_irq_optional() to avoid error message
  pinctrl: dt-bindings: Fix some errors in the lgm and pinmux schema
  pinctrl: intel: Pass irqchip when adding gpiochip
  pinctrl: intel: Add GPIO <-> pin mapping ranges via callback
  pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output
  pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins
  pinctrl: sunrisepoint: Add missing Interrupt Status register offset
  pinctrl: sh-pfc: Split R-Car H3 support in two independent drivers
  pinctrl: artpec6: fix __iomem on reg in set
  pinctrl: ingenic: Use devm_platform_ioremap_resource()
  pinctrl: ingenic: Factorize irq_set_type function
  pinctrl: ingenic: Remove duplicated ingenic_chip_info structures
  ...

Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml

@@ -54,8 +54,9 @@ patternProperties:
               TACH10, TACH11, TACH12, TACH13, TACH14, TACH15, TACH2, TACH3,
               TACH4, TACH5, TACH6, TACH7, TACH8, TACH9, THRU0, THRU1, THRU2,
               THRU3, TXD1, TXD2, TXD3, TXD4, UART10, UART11, UART12, UART13,
-              UART6, UART7, UART8, UART9, VB, VGAHS, VGAVS, WDTRST1, WDTRST2,
-              WDTRST3, WDTRST4, ]
+              UART6, UART7, UART8, UART9, USBAD, USBADP, USB2AH, USB2AHP,
+              USB2BD, USB2BH, VB, VGAHS, VGAVS, WDTRST1, WDTRST2, WDTRST3,
+              WDTRST4, ]
         groups:
           allOf:
             - $ref: "/schemas/types.yaml#/definitions/string"
@@ -85,8 +86,8 @@ patternProperties:
               TACH10, TACH11, TACH12, TACH13, TACH14, TACH15, TACH2, TACH3,
               TACH4, TACH5, TACH6, TACH7, TACH8, TACH9, THRU0, THRU1, THRU2,
               THRU3, TXD1, TXD2, TXD3, TXD4, UART10, UART11, UART12G0,
-              UART12G1, UART13G0, UART13G1, UART6, UART7, UART8, UART9, VB,
-              VGAHS, VGAVS, WDTRST1, WDTRST2, WDTRST3, WDTRST4, ]
+              UART12G1, UART13G0, UART13G1, UART6, UART7, UART8, UART9, USBA,
+              USBB, VB, VGAHS, VGAVS, WDTRST1, WDTRST2, WDTRST3, WDTRST4, ]
 
 required:
   - compatible

Documentation/devicetree/bindings/pinctrl/fsl,imx8mp-pinctrl.yaml

@@ -0,0 +1,69 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/fsl,imx8mp-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale IMX8MP IOMUX Controller
+
+maintainers:
+  - Anson Huang <[email protected]>
+
+description:
+  Please refer to fsl,imx-pinctrl.txt and pinctrl-bindings.txt in this directory
+  for common binding part and usage.
+
+properties:
+  compatible:
+    const: fsl,imx8mp-iomuxc
+
+  reg:
+    maxItems: 1
+
+# Client device subnode's properties
+patternProperties:
+  'grp$':
+    type: object
+    description:
+      Pinctrl node's client devices use subnodes for desired pin configuration.
+      Client device subnodes use below standard properties.
+
+    properties:
+      fsl,pins:
+        allOf:
+          - $ref: /schemas/types.yaml#/definitions/uint32-array
+        description:
+          each entry consists of 6 integers and represents the mux and config
+          setting for one pin. The first 5 integers <mux_reg conf_reg input_reg
+          mux_val input_val> are specified using a PIN_FUNC_ID macro, which can
+          be found in <arch/arm64/boot/dts/freescale/imx8mp-pinfunc.h>. The last
+          integer CONFIG is the pad setting value like pull-up on this pin. Please
+          refer to i.MX8M Plus Reference Manual for detailed CONFIG settings.
+
+    required:
+      - fsl,pins
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  # Pinmux controller node
+  - |
+    iomuxc: pinctrl@30330000 {
+        compatible = "fsl,imx8mp-iomuxc";
+        reg = <0x30330000 0x10000>;
+
+        pinctrl_uart2: uart2grp {
+            fsl,pins = <
+                0x228 0x488 0x5F0 0x0 0x6	0x49
+                0x228 0x488 0x000 0x0 0x0	0x49
+            >;
+        };
+    };
+
+...

Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt

@@ -10,9 +10,9 @@ GPIO port configuration registers and it is typical to refer to pins using the
 naming scheme "PxN" where x is a character identifying the GPIO port with
 which the pin is associated and N is an integer from 0 to 31 identifying the
 pin within that GPIO port. For example PA0 is the first pin in GPIO port A, and
-PB31 is the last pin in GPIO port B. The jz4740 and the x1000 contains 4 GPIO
-ports, PA to PD, for a total of 128 pins. The jz4760, the jz4770 and the jz4780
-contains 6 GPIO ports, PA to PF, for a total of 192 pins.
+PB31 is the last pin in GPIO port B. The jz4740, the x1000 and the x1830
+contains 4 GPIO ports, PA to PD, for a total of 128 pins. The jz4760, the
+jz4770 and the jz4780 contains 6 GPIO ports, PA to PF, for a total of 192 pins.
 
 
 Required properties:
@@ -28,6 +28,7 @@ Required properties:
     - "ingenic,x1000-pinctrl"
     - "ingenic,x1000e-pinctrl"
     - "ingenic,x1500-pinctrl"
+    - "ingenic,x1830-pinctrl"
  - reg: Address range of the pinctrl registers.
 
 
@@ -40,6 +41,7 @@ Required properties for sub-nodes (GPIO chips):
     - "ingenic,jz4770-gpio"
     - "ingenic,jz4780-gpio"
     - "ingenic,x1000-gpio"
+    - "ingenic,x1830-gpio"
  - reg: The GPIO bank number.
  - interrupt-controller: Marks the device node as an interrupt controller.
  - interrupts: Interrupt specifier for the controllers interrupt.

Documentation/devicetree/bindings/pinctrl/intel,lgm-io.yaml

@@ -0,0 +1,75 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/intel,lgm-io.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Intel Lightning Mountain SoC pinmux & GPIO controller binding
+
+maintainers:
+  - Rahul Tanwar <[email protected]>
+
+description: |
+  Pinmux & GPIO controller controls pin multiplexing & configuration including
+  GPIO function selection & GPIO attributes configuration.
+
+properties:
+  compatible:
+    const: intel,lgm-io
+
+  reg:
+    maxItems: 1
+
+# Client device subnode's properties
+patternProperties:
+  '-pins$':
+    type: object
+    allOf:
+      - $ref: pincfg-node.yaml#
+      - $ref: pinmux-node.yaml#
+    description:
+      Pinctrl node's client devices use subnodes for desired pin configuration.
+      Client device subnodes use below standard properties.
+
+    properties:
+      function: true
+      groups: true
+      pins: true
+      pinmux: true
+      bias-pull-up: true
+      bias-pull-down: true
+      drive-strength: true
+      slew-rate: true
+      drive-open-drain: true
+      output-enable: true
+
+    required:
+      - function
+      - groups
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  # Pinmux controller node
+  - |
+    pinctrl: pinctrl@e2880000 {
+        compatible = "intel,lgm-io";
+        reg = <0xe2880000 0x100000>;
+
+        uart0-pins {
+             pins = <64>, /* UART_RX0 */
+                    <65>; /* UART_TX0 */
+             function = "CONSOLE_UART0";
+             pinmux = <1>,
+                      <1>;
+             groups = "CONSOLE_UART0";
+          };
+    };
+
+...

Documentation/devicetree/bindings/pinctrl/pinmux-node.yaml

@@ -114,7 +114,7 @@ properties:
       specific binding for the hardware defines whether the entries are integers
       or strings, and their meaning.
 
-  group:
+  groups:
     $ref: /schemas/types.yaml#/definitions/string-array
     description:
       the group to apply the properties to, if the driver supports

Documentation/devicetree/bindings/pinctrl/qcom,sc7180-pinctrl.txt

@@ -125,8 +125,9 @@ to specify in a pin configuration subnode:
 		    mi2s_1, mi2s_2, mss_lte, m_voc, pa_indicator, phase_flag,
 		    PLL_BIST, pll_bypassnl, pll_reset, prng_rosc, qdss,
 		    qdss_cti, qlink_enable, qlink_request, qspi_clk, qspi_cs,
-		    qspi_data, qup00, qup01, qup02, qup03, qup04, qup05,
-		    qup10, qup11, qup12, qup13, qup14, qup15, sdc1_tb,
+		    qspi_data, qup00, qup01, qup02_i2c, qup02_uart, qup03,
+		    qup04_i2c, qup04_uart, qup05, qup10, qup11_i2c, qup11_uart,
+		    qup12, qup13_i2c, qup13_uart, qup14, qup15, sdc1_tb,
 		    sdc2_tb, sd_write, sp_cmu, tgu_ch0, tgu_ch1, tgu_ch2,
 		    tgu_ch3, tsense_pwm1, tsense_pwm2, uim1, uim2, uim_batt,
 		    usb_phy, vfr_1, _V_GPIO, _V_PPS_IN, _V_PPS_OUT,

Documentation/driver-api/gpio/driver.rst

@@ -507,11 +507,6 @@ available but we try to move away from this:
   cascaded irq has to be handled by a threaded interrupt handler.
   Apart from that it works exactly like the chained irqchip.
 
-- DEPRECATED: gpiochip_set_chained_irqchip(): sets up a chained cascaded irq
-  handler for a gpio_chip from a parent IRQ and passes the struct gpio_chip*
-  as handler data. Notice that we pass is as the handler data, since the
-  irqchip data is likely used by the parent irqchip.
-
 - gpiochip_set_nested_irqchip(): sets up a nested cascaded irq handler for a
   gpio_chip from a parent IRQ. As the parent IRQ has usually been
   explicitly requested by the driver, this does very little more than

MAINTAINERS

@@ -8383,7 +8383,6 @@ S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel.git
 F:	drivers/gpio/gpio-ich.c
 F:	drivers/gpio/gpio-intel-mid.c
-F:	drivers/gpio/gpio-lynxpoint.c
 F:	drivers/gpio/gpio-merrifield.c
 F:	drivers/gpio/gpio-ml-ioh.c
 F:	drivers/gpio/gpio-pch.c

arch/arm/mach-u300/core.c

@@ -201,7 +201,7 @@ static unsigned long pin_highz_conf[] = {
 };
 
 /* Pin control settings */
-static struct pinctrl_map __initdata u300_pinmux_map[] = {
+static const struct pinctrl_map u300_pinmux_map[] = {
 	/* anonymous maps for chip power and EMIFs */
 	PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "power"),
 	PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-u300", NULL, "emif0"),

arch/sh/include/cpu-sh2a/cpu/sh7264.h

@@ -112,12 +112,6 @@ enum {
 	GPIO_FN_TIOC0D, GPIO_FN_TIOC0C, GPIO_FN_TIOC0B, GPIO_FN_TIOC0A,
 	GPIO_FN_TCLKD, GPIO_FN_TCLKC, GPIO_FN_TCLKB, GPIO_FN_TCLKA,
 
-	/* SSU */
-	GPIO_FN_SCS0_PD, GPIO_FN_SSO0_PD, GPIO_FN_SSI0_PD, GPIO_FN_SSCK0_PD,
-	GPIO_FN_SCS0_PF, GPIO_FN_SSO0_PF, GPIO_FN_SSI0_PF, GPIO_FN_SSCK0_PF,
-	GPIO_FN_SCS1_PD, GPIO_FN_SSO1_PD, GPIO_FN_SSI1_PD, GPIO_FN_SSCK1_PD,
-	GPIO_FN_SCS1_PF, GPIO_FN_SSO1_PF, GPIO_FN_SSI1_PF, GPIO_FN_SSCK1_PF,
-
 	/* SCIF */
 	GPIO_FN_SCK0, GPIO_FN_SCK1, GPIO_FN_SCK2, GPIO_FN_SCK3,
 	GPIO_FN_RXD0, GPIO_FN_RXD1, GPIO_FN_RXD2, GPIO_FN_RXD3,