Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (187 commits)
  sh: remove dead LED code for migo-r and ms7724se
  sh: ecovec build fix for CONFIG_I2C=n
  sh: ecovec r-standby support
  sh: ms7724se r-standby support
  sh: SH-Mobile R-standby register save/restore
  clocksource: Fix up a registration/IRQ race in the sh drivers.
  sh: ms7724: modify scan_timing for KEYSC
  sh: ms7724: Add sh_sir support
  sh: mach-ecovec24: Add sh_sir support
  sh: wire up SET/GET_UNALIGN_CTL.
  sh: allow alignment fault mode to be configured at kernel boot.
  sh: sh7724: Update FSI/SPU2 clock
  sh: always enable sh7724 vpu_clk and set to 166MHz on Ecovec
  sh: add sh7724 kick callback to clk_div4_table
  sh: introduce struct clk_div4_table
  sh: clock-cpg div4 set_rate() shift fix
  sh: Turn on speculative return for SH7785 and SH7786
  sh: Merge legacy and dynamic PMB modes.
  sh: Use uncached I/O helpers in PMB setup.
  sh: Provide uncached I/O helpers.
  ...

arch/sh/Kconfig

@@ -13,7 +13,6 @@ config SUPERH
 	select HAVE_LMB
 	select HAVE_OPROFILE
 	select HAVE_GENERIC_DMA_COHERENT
-	select HAVE_IOREMAP_PROT if MMU
 	select HAVE_ARCH_TRACEHOOK
 	select HAVE_DMA_API_DEBUG
 	select HAVE_DMA_ATTRS
@@ -22,6 +21,7 @@ config SUPERH
 	select HAVE_KERNEL_GZIP
 	select HAVE_KERNEL_BZIP2
 	select HAVE_KERNEL_LZMA
+	select HAVE_KERNEL_LZO
 	select HAVE_SYSCALL_TRACEPOINTS
 	select RTC_LIB
 	select GENERIC_ATOMIC64
@@ -35,13 +35,16 @@ config SUPERH32
 	def_bool ARCH = "sh"
 	select HAVE_KPROBES
 	select HAVE_KRETPROBES
+	select HAVE_IOREMAP_PROT if MMU && !X2TLB
 	select HAVE_FUNCTION_TRACER
 	select HAVE_FTRACE_MCOUNT_RECORD
 	select HAVE_DYNAMIC_FTRACE
 	select HAVE_FUNCTION_TRACE_MCOUNT_TEST
 	select HAVE_FTRACE_NMI_ENTER if DYNAMIC_FTRACE
 	select HAVE_FUNCTION_GRAPH_TRACER
 	select HAVE_ARCH_KGDB
+	select HAVE_HW_BREAKPOINT
+	select PERF_EVENTS if HAVE_HW_BREAKPOINT
 	select ARCH_HIBERNATION_POSSIBLE if MMU
 
 config SUPERH64
@@ -78,11 +81,12 @@ config GENERIC_HARDIRQS
 config GENERIC_HARDIRQS_NO__DO_IRQ
 	def_bool y
 
-config GENERIC_IRQ_PROBE
+config IRQ_PER_CPU
 	def_bool y
 
-config IRQ_PER_CPU
+config SPARSE_IRQ
 	def_bool y
+	depends on SUPERH32
 
 config GENERIC_GPIO
 	def_bool n
@@ -548,8 +552,7 @@ config SH_PCLK_FREQ
 			      CPU_SUBTYPE_SH7203 || \
 			      CPU_SUBTYPE_SH7206 || \
 			      CPU_SUBTYPE_SH7263 || \
-			      CPU_SUBTYPE_MXG    || \
-			      CPU_SUBTYPE_SH7786
+			      CPU_SUBTYPE_MXG
 	default "60000000" if CPU_SUBTYPE_SH7751 || CPU_SUBTYPE_SH7751R
 	default "66000000" if CPU_SUBTYPE_SH4_202
 	default "50000000"
@@ -563,7 +566,8 @@ config SH_CLK_CPG
 
 config SH_CLK_CPG_LEGACY
 	depends on SH_CLK_CPG
-	def_bool y if !CPU_SUBTYPE_SH7785 && !ARCH_SHMOBILE
+	def_bool y if !CPU_SUBTYPE_SH7785 && !ARCH_SHMOBILE && \
+		      !CPU_SUBTYPE_SH7786
 
 config SH_CLK_MD
 	int "CPU Mode Pin Setting"
@@ -725,18 +729,6 @@ config GUSA_RB
 	  LLSC, this should be more efficient than the other alternative of
 	  disabling interrupts around the atomic sequence.
 
-config SPARSE_IRQ
-	bool "Support sparse irq numbering"
-	depends on EXPERIMENTAL
-	help
-	  This enables support for sparse irqs. This is useful in general
-	  as most CPUs have a fairly sparse array of IRQ vectors, which
-	  the irq_desc then maps directly on to. Systems with a high
-	  number of off-chip IRQs will want to treat this as
-	  experimental until they have been independently verified.
-
-	  If you don't know what to do here, say N.
-
 endmenu
 
 menu "Boot options"
@@ -822,11 +814,15 @@ config MAPLE
 config PCI
 	bool "PCI support"
 	depends on SYS_SUPPORTS_PCI
+	select PCI_DOMAINS
 	help
 	  Find out whether you have a PCI motherboard. PCI is the name of a
 	  bus system, i.e. the way the CPU talks to the other stuff inside
 	  your box. If you have PCI, say Y, otherwise N.
 
+config PCI_DOMAINS
+	bool
+
 source "drivers/pci/pcie/Kconfig"
 
 source "drivers/pci/Kconfig"

arch/sh/Kconfig.cpu

@@ -68,7 +68,8 @@ config SH_STORE_QUEUES
 
 config SPECULATIVE_EXECUTION
 	bool "Speculative subroutine return"
-	depends on CPU_SUBTYPE_SH7780 && EXPERIMENTAL
+	depends on EXPERIMENTAL
+	depends on CPU_SUBTYPE_SH7780 || CPU_SUBTYPE_SH7785 || CPU_SUBTYPE_SH7786
 	help
 	  This enables support for a speculative instruction fetch for
 	  subroutine return. There are various pitfalls associated with

arch/sh/Makefile

@@ -83,6 +83,7 @@ defaultimage-$(CONFIG_SH_AP325RXA)		:= uImage
 defaultimage-$(CONFIG_SH_7724_SOLUTION_ENGINE)	:= uImage
 defaultimage-$(CONFIG_SH_7206_SOLUTION_ENGINE)	:= vmlinux
 defaultimage-$(CONFIG_SH_7619_SOLUTION_ENGINE)	:= vmlinux
+defaultimage-$(CONFIG_SH_SDK7786)		:= vmlinux.bin
 
 # Set some sensible Kbuild defaults
 KBUILD_IMAGE		:= $(defaultimage-y)
@@ -143,11 +144,11 @@ machdir-$(CONFIG_SH_AP325RXA)			+= mach-ap325rxa
 machdir-$(CONFIG_SH_KFR2R09)			+= mach-kfr2r09
 machdir-$(CONFIG_SH_ECOVEC)			+= mach-ecovec24
 machdir-$(CONFIG_SH_SDK7780)			+= mach-sdk7780
+machdir-$(CONFIG_SH_SDK7786)			+= mach-sdk7786
 machdir-$(CONFIG_SH_X3PROTO)			+= mach-x3proto
 machdir-$(CONFIG_SH_SH7763RDP)			+= mach-sh7763rdp
 machdir-$(CONFIG_SH_SH4202_MICRODEV)		+= mach-microdev
 machdir-$(CONFIG_SH_LANDISK)			+= mach-landisk
-machdir-$(CONFIG_SH_TITAN)			+= mach-titan
 machdir-$(CONFIG_SH_LBOX_RE2)			+= mach-lboxre2
 machdir-$(CONFIG_SH_CAYMAN)			+= mach-cayman
 machdir-$(CONFIG_SH_RSK)			+= mach-rsk
@@ -203,8 +204,9 @@ endif
 libs-$(CONFIG_SUPERH32)		:= arch/sh/lib/	$(libs-y)
 libs-$(CONFIG_SUPERH64)		:= arch/sh/lib64/ $(libs-y)
 
-BOOT_TARGETS = uImage uImage.bz2 uImage.gz uImage.lzma uImage.srec uImage.bin \
-	       zImage vmlinux.srec romImage
+BOOT_TARGETS = uImage uImage.bz2 uImage.gz uImage.lzma uImage.lzo \
+	       uImage.srec uImage.bin zImage vmlinux.bin vmlinux.srec \
+	       romImage
 PHONY += $(BOOT_TARGETS)
 
 all: $(KBUILD_IMAGE)
@@ -225,10 +227,12 @@ define archhelp
 	@echo '  zImage 	           - Compressed kernel image'
 	@echo '  romImage	           - Compressed ROM image, if supported'
 	@echo '  vmlinux.srec	           - Create an ELF S-record'
+	@echo '  vmlinux.bin	           - Create an uncompressed binary image'
 	@echo '* uImage  	           - Alias to bootable U-Boot image'
 	@echo '  uImage.srec	           - Create an S-record for U-Boot'
 	@echo '  uImage.bin	           - Kernel-only image for U-Boot (bin)'
 	@echo '* uImage.gz	           - Kernel-only image for U-Boot (gzip)'
 	@echo '  uImage.bz2	           - Kernel-only image for U-Boot (bzip2)'
 	@echo '  uImage.lzma	           - Kernel-only image for U-Boot (lzma)'
+	@echo '  uImage.lzo	           - Kernel-only image for U-Boot (lzo)'
 endef

arch/sh/boards/Kconfig

@@ -150,6 +150,14 @@ config SH_SDK7780
 	  Select SDK7780 if configuring for a Renesas SH7780 SDK7780R3
 	  evaluation board.
 
+config SH_SDK7786
+	bool "SDK7786"
+	depends on CPU_SUBTYPE_SH7786
+	select SYS_SUPPORTS_PCI
+	help
+	  Select SDK7786 if configuring for a Renesas Technology Europe
+	  SH7786-65nm board.
+
 config SH_HIGHLANDER
 	bool "Highlander"
 	depends on CPU_SUBTYPE_SH7780 || CPU_SUBTYPE_SH7785

arch/sh/boards/Makefile

@@ -8,3 +8,4 @@ obj-$(CONFIG_SH_SHMIN)		+= board-shmin.o
 obj-$(CONFIG_SH_EDOSK7760)	+= board-edosk7760.o
 obj-$(CONFIG_SH_ESPT)		+= board-espt.o
 obj-$(CONFIG_SH_POLARIS)	+= board-polaris.o
+obj-$(CONFIG_SH_TITAN)		+= board-titan.o

arch/sh/boards/board-magicpanelr2.c

@@ -23,7 +23,7 @@
 #include <asm/heartbeat.h>
 #include <cpu/sh7720.h>
 
-#define LAN9115_READY	(ctrl_inl(0xA8000084UL) & 0x00000001UL)
+#define LAN9115_READY	(__raw_readl(0xA8000084UL) & 0x00000001UL)
 
 /* Prefer cmdline over RedBoot */
 static const char *probes[] = { "cmdlinepart", "RedBoot", NULL };
@@ -60,105 +60,105 @@ static void __init setup_chip_select(void)
 {
 	/* CS2: LAN (0x08000000 - 0x0bffffff) */
 	/* no idle cycles, normal space, 8 bit data bus */
-	ctrl_outl(0x36db0400, CS2BCR);
+	__raw_writel(0x36db0400, CS2BCR);
 	/* (SW:1.5 WR:3 HW:1.5), ext. wait */
-	ctrl_outl(0x000003c0, CS2WCR);
+	__raw_writel(0x000003c0, CS2WCR);
 
 	/* CS4: CAN1 (0xb0000000 - 0xb3ffffff) */
 	/* no idle cycles, normal space, 8 bit data bus */
-	ctrl_outl(0x00000200, CS4BCR);
+	__raw_writel(0x00000200, CS4BCR);
 	/* (SW:1.5 WR:3 HW:1.5), ext. wait */
-	ctrl_outl(0x00100981, CS4WCR);
+	__raw_writel(0x00100981, CS4WCR);
 
 	/* CS5a: CAN2 (0xb4000000 - 0xb5ffffff) */
 	/* no idle cycles, normal space, 8 bit data bus */
-	ctrl_outl(0x00000200, CS5ABCR);
+	__raw_writel(0x00000200, CS5ABCR);
 	/* (SW:1.5 WR:3 HW:1.5), ext. wait */
-	ctrl_outl(0x00100981, CS5AWCR);
+	__raw_writel(0x00100981, CS5AWCR);
 
 	/* CS5b: CAN3 (0xb6000000 - 0xb7ffffff) */
 	/* no idle cycles, normal space, 8 bit data bus */
-	ctrl_outl(0x00000200, CS5BBCR);
+	__raw_writel(0x00000200, CS5BBCR);
 	/* (SW:1.5 WR:3 HW:1.5), ext. wait */
-	ctrl_outl(0x00100981, CS5BWCR);
+	__raw_writel(0x00100981, CS5BWCR);
 
 	/* CS6a: Rotary (0xb8000000 - 0xb9ffffff) */
 	/* no idle cycles, normal space, 8 bit data bus */
-	ctrl_outl(0x00000200, CS6ABCR);
+	__raw_writel(0x00000200, CS6ABCR);
 	/* (SW:1.5 WR:3 HW:1.5), no ext. wait */
-	ctrl_outl(0x001009C1, CS6AWCR);
+	__raw_writel(0x001009C1, CS6AWCR);
 }
 
 static void __init setup_port_multiplexing(void)
 {
 	/* A7 GPO(LED8);     A6 GPO(LED7);     A5 GPO(LED6);	  A4 GPO(LED5);
 	 * A3 GPO(LED4);     A2 GPO(LED3);     A1 GPO(LED2);	  A0 GPO(LED1);
 	 */
-	ctrl_outw(0x5555, PORT_PACR);	/* 01 01 01 01 01 01 01 01 */
+	__raw_writew(0x5555, PORT_PACR);	/* 01 01 01 01 01 01 01 01 */
 
 	/* B7 GPO(RST4);   B6 GPO(RST3);  B5 GPO(RST2);    B4 GPO(RST1);
 	 * B3 GPO(PB3);	   B2 GPO(PB2);	  B1 GPO(PB1);	   B0 GPO(PB0);
 	 */
-	ctrl_outw(0x5555, PORT_PBCR);	/* 01 01 01 01 01 01 01 01 */
+	__raw_writew(0x5555, PORT_PBCR);	/* 01 01 01 01 01 01 01 01 */
 
 	/* C7 GPO(PC7);	  C6 GPO(PC6);	  C5 GPO(PC5);	   C4 GPO(PC4);
 	 * C3 LCD_DATA3;  C2 LCD_DATA2;   C1 LCD_DATA1;	   C0 LCD_DATA0;
 	 */
-	ctrl_outw(0x5500, PORT_PCCR);	/* 01 01 01 01 00 00 00 00 */
+	__raw_writew(0x5500, PORT_PCCR);	/* 01 01 01 01 00 00 00 00 */
 
 	/* D7 GPO(PD7);	D6 GPO(PD6);	D5 GPO(PD5);	   D4 GPO(PD4);
 	 * D3 GPO(PD3);	D2 GPO(PD2);	D1 GPO(PD1);	   D0 GPO(PD0);
 	 */
-	ctrl_outw(0x5555, PORT_PDCR);	/* 01 01 01 01 01 01 01 01 */
+	__raw_writew(0x5555, PORT_PDCR);	/* 01 01 01 01 01 01 01 01 */
 
 	/* E7 (x);	  E6 GPI(nu);	 E5 GPI(nu);	  E4 LCD_M_DISP;
 	 * E3 LCD_CL1;	  E2 LCD_CL2;	 E1 LCD_DON;	  E0 LCD_FLM;
 	 */
-	ctrl_outw(0x3C00, PORT_PECR);	/* 00 11 11 00 00 00 00 00 */
+	__raw_writew(0x3C00, PORT_PECR);	/* 00 11 11 00 00 00 00 00 */
 
 	/* F7 (x);	     F6 DA1(VLCD);     F5 DA0(nc);	  F4 AN3;
 	 * F3 AN2(MID_AD);   F2 AN1(EARTH_AD); F1 AN0(TEMP);	  F0 GPI+(nc);
 	 */
-	ctrl_outw(0x0002, PORT_PFCR);	/* 00 00 00 00 00 00 00 10 */
+	__raw_writew(0x0002, PORT_PFCR);	/* 00 00 00 00 00 00 00 10 */
 
 	/* G7 (x);	  G6 IRQ5(TOUCH_BUSY); G5 IRQ4(TOUCH_IRQ); G4 GPI(KEY2);
 	 * G3 GPI(KEY1);  G2 GPO(LED11);	G1 GPO(LED10);     G0 GPO(LED9);
 	 */
-	ctrl_outw(0x03D5, PORT_PGCR);	/* 00 00 00 11 11 01 01 01 */
+	__raw_writew(0x03D5, PORT_PGCR);	/* 00 00 00 11 11 01 01 01 */
 
 	/* H7 (x);	      H6 /RAS(BRAS);	  H5 /CAS(BCAS); H4 CKE(BCKE);
 	 * H3 GPO(EARTH_OFF); H2 GPO(EARTH_TEST); H1 USB2_PWR;	 H0 USB1_PWR;
 	 */
-	ctrl_outw(0x0050, PORT_PHCR);	/* 00 00 00 00 01 01 00 00 */
+	__raw_writew(0x0050, PORT_PHCR);	/* 00 00 00 00 01 01 00 00 */
 
 	/* J7 (x);	  J6 AUDCK;	   J5 ASEBRKAK;	    J4 AUDATA3;
 	 * J3 AUDATA2;	  J2 AUDATA1;	   J1 AUDATA0;	    J0 AUDSYNC;
 	 */
-	ctrl_outw(0x0000, PORT_PJCR);	/* 00 00 00 00 00 00 00 00 */
+	__raw_writew(0x0000, PORT_PJCR);	/* 00 00 00 00 00 00 00 00 */
 
 	/* K7 (x);	    K6 (x);	     K5 (x);	   K4 (x);
 	 * K3 PINT7(/PWR2); K2 PINT6(/PWR1); K1 PINT5(nu); K0 PINT4(FLASH_READY)
 	 */
-	ctrl_outw(0x00FF, PORT_PKCR);	/* 00 00 00 00 11 11 11 11 */
+	__raw_writew(0x00FF, PORT_PKCR);	/* 00 00 00 00 11 11 11 11 */
 
 	/* L7 TRST;	   L6 TMS;	     L5 TDO;		  L4 TDI;
 	 * L3 TCK;	   L2 (x);	     L1 (x);		  L0 (x);
 	 */
-	ctrl_outw(0x0000, PORT_PLCR);	/* 00 00 00 00 00 00 00 00 */
+	__raw_writew(0x0000, PORT_PLCR);	/* 00 00 00 00 00 00 00 00 */
 
 	/* M7 GPO(CURRENT_SINK);    M6 GPO(PWR_SWITCH);     M5 GPO(LAN_SPEED);
 	 * M4 GPO(LAN_RESET);       M3 GPO(BUZZER);	    M2 GPO(LCD_BL);
 	 * M1 CS5B(CAN3_CS);	    M0 GPI+(nc);
 	 */
-	ctrl_outw(0x5552, PORT_PMCR);	   /* 01 01 01 01 01 01 00 10 */
+	__raw_writew(0x5552, PORT_PMCR);	   /* 01 01 01 01 01 01 00 10 */
 
 	/* CURRENT_SINK=off,	PWR_SWITCH=off, LAN_SPEED=100MBit,
 	 * LAN_RESET=off,	BUZZER=off,	LCD_BL=off
 	 */
 #if CONFIG_SH_MAGIC_PANEL_R2_VERSION == 2
-	ctrl_outb(0x30, PORT_PMDR);
+	__raw_writeb(0x30, PORT_PMDR);
 #elif CONFIG_SH_MAGIC_PANEL_R2_VERSION == 3
-	ctrl_outb(0xF0, PORT_PMDR);
+	__raw_writeb(0xF0, PORT_PMDR);
 #else
 #error Unknown revision of PLATFORM_MP_R2
 #endif
@@ -167,8 +167,8 @@ static void __init setup_port_multiplexing(void)
 	 * P4 GPO(nu);	       P3 IRQ3(LAN_IRQ);  P2 IRQ2(CAN3_IRQ);
 	 * P1 IRQ1(CAN2_IRQ);  P0 IRQ0(CAN1_IRQ)
 	 */
-	ctrl_outw(0x0100, PORT_PPCR);	/* 00 00 00 01 00 00 00 00 */
-	ctrl_outb(0x10, PORT_PPDR);
+	__raw_writew(0x0100, PORT_PPCR);	/* 00 00 00 01 00 00 00 00 */
+	__raw_writeb(0x10, PORT_PPDR);
 
 	/* R7 A25;	     R6 A24;	     R5 A23;		  R4 A22;
 	 * R3 A21;	     R2 A20;	     R1 A19;		  R0 A0;
@@ -185,22 +185,22 @@ static void __init setup_port_multiplexing(void)
 	/* S7 (x);		S6 (x);        S5 (x);	     S4 GPO(EEPROM_CS2);
 	 * S3 GPO(EEPROM_CS1);  S2 SIOF0_TXD;  S1 SIOF0_RXD; S0 SIOF0_SCK;
 	 */
-	ctrl_outw(0x0140, PORT_PSCR);	/* 00 00 00 01 01 00 00 00 */
+	__raw_writew(0x0140, PORT_PSCR);	/* 00 00 00 01 01 00 00 00 */
 
 	/* T7 (x);	   T6 (x);	  T5 (x);	  T4 COM1_CTS;
 	 * T3 COM1_RTS;	   T2 COM1_TXD;	  T1 COM1_RXD;	  T0 GPO(WDOG)
 	 */
-	ctrl_outw(0x0001, PORT_PTCR);	/* 00 00 00 00 00 00 00 01 */
+	__raw_writew(0x0001, PORT_PTCR);	/* 00 00 00 00 00 00 00 01 */
 
 	/* U7 (x);	     U6 (x);	   U5 (x);	  U4 GPI+(/AC_FAULT);
 	 * U3 GPO(TOUCH_CS); U2 TOUCH_TXD; U1 TOUCH_RXD;  U0 TOUCH_SCK;
 	 */
-	ctrl_outw(0x0240, PORT_PUCR);	/* 00 00 00 10 01 00 00 00 */
+	__raw_writew(0x0240, PORT_PUCR);	/* 00 00 00 10 01 00 00 00 */
 
 	/* V7 (x);	  V6 (x);	V5 (x);		  V4 GPO(MID2);
 	 * V3 GPO(MID1);  V2 CARD_TxD;	V1 CARD_RxD;	  V0 GPI+(/BAT_FAULT);
 	 */
-	ctrl_outw(0x0142, PORT_PVCR);	/* 00 00 00 01 01 00 00 10 */
+	__raw_writew(0x0142, PORT_PVCR);	/* 00 00 00 01 01 00 00 10 */
 }
 
 static void __init mpr2_setup(char **cmdline_p)
@@ -209,24 +209,24 @@ static void __init mpr2_setup(char **cmdline_p)
 	 * /PCC_CD1, /PCC_CD2,  PCC_BVD1, PCC_BVD2,
 	 * /IOIS16,  IRQ4,	IRQ5,	  USB1d_SUSPEND
 	 */
-	ctrl_outw(0xAABC, PORT_PSELA);
+	__raw_writew(0xAABC, PORT_PSELA);
 	/* set Pin Select Register B:
 	 * /SCIF0_RTS, /SCIF0_CTS, LCD_VCPWC,
 	 * LCD_VEPWC,  IIC_SDA,    IIC_SCL, Reserved
 	 */
-	ctrl_outw(0x3C00, PORT_PSELB);
+	__raw_writew(0x3C00, PORT_PSELB);
 	/* set Pin Select Register C:
 	 * SIOF1_SCK, SIOF1_RxD, SCIF1_RxD, SCIF1_TxD, Reserved
 	 */
-	ctrl_outw(0x0000, PORT_PSELC);
+	__raw_writew(0x0000, PORT_PSELC);
 	/* set Pin Select Register D: Reserved, SIOF1_TxD, Reserved, SIOF1_MCLK,
 	 * Reserved, SIOF1_SYNC, Reserved, SCIF1_SCK, Reserved
 	 */
-	ctrl_outw(0x0000, PORT_PSELD);
+	__raw_writew(0x0000, PORT_PSELD);
 	/* set USB TxRx Control: Reserved, DRV, Reserved, USB_TRANS, USB_SEL */
-	ctrl_outw(0x0101, PORT_UTRCTL);
+	__raw_writew(0x0101, PORT_UTRCTL);
 	/* set USB Clock Control: USSCS, USSTB, Reserved (HighByte always A5) */
-	ctrl_outw(0xA5C0, PORT_UCLKCR_W);
+	__raw_writew(0xA5C0, PORT_UCLKCR_W);
 
 	setup_chip_select();