Merge tag 'spi-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git…

…/broonie/spi

Pull spi updates from Mark Brown:
 "A quiet release for SPI, not even many driver updates:

   - Add a dummy loopback driver for use in exercising framework
     features during development.

   - Move the test utilities to tools/ and add support for transferring
     data to and from a file instead of stdin and stdout to spidev_test.

   - Support for Mediatek MT2701 and Renesas AG5 deices"

* tag 'spi-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (69 commits)
  spi: loopback: fix typo in MODULE_PARM_DESC
  spi: sun4i: Prevent chip-select from being activated twice before a transfer
  spi: loopback-test: spi_check_rx_ranges can get always done
  spi: loopback-test: rename method spi_test_fill_tx to spi_test_fill_pattern
  spi: loopback-test: write rx pattern also when running without tx_buf
  spi: fsl-espi: expose maximum transfer size limit
  spi: expose master transfer size limitation.
  spi: zynq: use to_platform_device()
  spi: cadence: use to_platform_device()
  spi: mediatek: Add spi support for mt2701 IC
  spi: mediatek: merge all identical compat to mtk_common_compat
  spi: mtk: Add bindings for mediatek MT2701 soc platform
  spi: mediatek: Prevent overflows in FIFO transfers
  spi: s3c64xx: Remove unused platform_device_id entries
  spi: use to_spi_device
  spi: dw: Use SPI_TMOD_TR rather than magic const 0 to set tmode
  spi: imx: defer spi initialization, if DMA engine is
  spi: imx: return error from dma channel request
  spi: imx: enable loopback only for ECSPI controller family
  spi: imx: fix loopback mode setup after controller reset
  ...

Documentation/Makefile

@@ -1,4 +1,4 @@
 subdir-y := accounting auxdisplay blackfin connector \
 	filesystems filesystems ia64 laptops mic misc-devices \
-	networking pcmcia prctl ptp spi timers vDSO video4linux \
+	networking pcmcia prctl ptp timers vDSO video4linux \
 	watchdog

Documentation/devicetree/bindings/spi/sh-msiof.txt

@@ -10,6 +10,7 @@ Required properties:
 			 "renesas,msiof-r8a7792" (R-Car V2H)
 			 "renesas,msiof-r8a7793" (R-Car M2-N)
 			 "renesas,msiof-r8a7794" (R-Car E2)
+			 "renesas,msiof-sh73a0" (SH-Mobile AG5)
 - reg                  : A list of offsets and lengths of the register sets for
 			 the device.
 			 If only one register set is present, it is to be used

Documentation/devicetree/bindings/spi/spi-mt65xx.txt

@@ -2,9 +2,10 @@ Binding for MTK SPI controller
 
 Required properties:
 - compatible: should be one of the following.
-    - mediatek,mt8173-spi: for mt8173 platforms
-    - mediatek,mt8135-spi: for mt8135 platforms
+    - mediatek,mt2701-spi: for mt2701 platforms
     - mediatek,mt6589-spi: for mt6589 platforms
+    - mediatek,mt8135-spi: for mt8135 platforms
+    - mediatek,mt8173-spi: for mt8173 platforms
 
 - #address-cells: should be 1.
 
@@ -29,10 +30,10 @@ Required properties:
   muxes clock, and "spi-clk" for the clock gate.
 
 Optional properties:
--cs-gpios: see spi-bus.txt, only required for MT8173.
+-cs-gpios: see spi-bus.txt.
 
 - mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi
-  controller used. This is a array, the element value should be 0~3,
+  controller used. This is an array, the element value should be 0~3,
   only required for MT8173.
     0: specify GPIO69,70,71,72 for spi pins.
     1: specify GPIO102,103,104,105 for spi pins.

Documentation/spi/00-INDEX

@@ -10,13 +10,9 @@ pxa2xx
 	- PXA2xx SPI master controller build by spi_message fifo wq
 spidev
 	- Intro to the userspace API for spi devices
-spidev_fdx.c
-	- spidev example file
 spi-lm70llp
 	- Connecting an LM70-LLP sensor to the kernel via the SPI subsys.
 spi-sc18is602
 	- NXP SC18IS602/603 I2C-bus to SPI bridge
 spi-summary
 	- (Linux) SPI overview. If unsure about SPI or SPI in Linux, start here.
-spidev_test.c
-	- SPI testing utility.

arch/arm/plat-samsung/devs.c

@@ -1100,9 +1100,7 @@ struct platform_device s3c_device_wdt = {
 #ifdef CONFIG_S3C64XX_DEV_SPI0
 static struct resource s3c64xx_spi0_resource[] = {
 	[0] = DEFINE_RES_MEM(S3C_PA_SPI0, SZ_256),
-	[1] = DEFINE_RES_DMA(DMACH_SPI0_TX),
-	[2] = DEFINE_RES_DMA(DMACH_SPI0_RX),
-	[3] = DEFINE_RES_IRQ(IRQ_SPI0),
+	[1] = DEFINE_RES_IRQ(IRQ_SPI0),
 };
 
 struct platform_device s3c64xx_device_spi0 = {
@@ -1130,6 +1128,8 @@ void __init s3c64xx_spi0_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
 	pd.num_cs = num_cs;
 	pd.src_clk_nr = src_clk_nr;
 	pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi0_cfg_gpio;
+	pd.dma_tx = (void *)DMACH_SPI0_TX;
+	pd.dma_rx = (void *)DMACH_SPI0_RX;
 #if defined(CONFIG_PL330_DMA)
 	pd.filter = pl330_filter;
 #elif defined(CONFIG_S3C64XX_PL080)
@@ -1145,9 +1145,7 @@ void __init s3c64xx_spi0_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
 #ifdef CONFIG_S3C64XX_DEV_SPI1
 static struct resource s3c64xx_spi1_resource[] = {
 	[0] = DEFINE_RES_MEM(S3C_PA_SPI1, SZ_256),
-	[1] = DEFINE_RES_DMA(DMACH_SPI1_TX),
-	[2] = DEFINE_RES_DMA(DMACH_SPI1_RX),
-	[3] = DEFINE_RES_IRQ(IRQ_SPI1),
+	[1] = DEFINE_RES_IRQ(IRQ_SPI1),
 };
 
 struct platform_device s3c64xx_device_spi1 = {
@@ -1175,22 +1173,23 @@ void __init s3c64xx_spi1_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
 	pd.num_cs = num_cs;
 	pd.src_clk_nr = src_clk_nr;
 	pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi1_cfg_gpio;
+	pd.dma_tx = (void *)DMACH_SPI1_TX;
+	pd.dma_rx = (void *)DMACH_SPI1_RX;
 #if defined(CONFIG_PL330_DMA)
 	pd.filter = pl330_filter;
 #elif defined(CONFIG_S3C64XX_PL080)
 	pd.filter = pl08x_filter_id;
 #endif
 
+
 	s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi1);
 }
 #endif /* CONFIG_S3C64XX_DEV_SPI1 */
 
 #ifdef CONFIG_S3C64XX_DEV_SPI2
 static struct resource s3c64xx_spi2_resource[] = {
 	[0] = DEFINE_RES_MEM(S3C_PA_SPI2, SZ_256),
-	[1] = DEFINE_RES_DMA(DMACH_SPI2_TX),
-	[2] = DEFINE_RES_DMA(DMACH_SPI2_RX),
-	[3] = DEFINE_RES_IRQ(IRQ_SPI2),
+	[1] = DEFINE_RES_IRQ(IRQ_SPI2),
 };
 
 struct platform_device s3c64xx_device_spi2 = {
@@ -1218,6 +1217,8 @@ void __init s3c64xx_spi2_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
 	pd.num_cs = num_cs;
 	pd.src_clk_nr = src_clk_nr;
 	pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi2_cfg_gpio;
+	pd.dma_tx = (void *)DMACH_SPI2_TX;
+	pd.dma_rx = (void *)DMACH_SPI2_RX;
 #if defined(CONFIG_PL330_DMA)
 	pd.filter = pl330_filter;
 #elif defined(CONFIG_S3C64XX_PL080)

drivers/spi/Kconfig

@@ -585,7 +585,7 @@ config SPI_TEGRA20_SLINK
 
 config SPI_TOPCLIFF_PCH
 	tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
-	depends on PCI && (X86_32 || COMPILE_TEST)
+	depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
 	help
 	  SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
 	  used in some x86 embedded processors.
@@ -689,6 +689,15 @@ config SPI_SPIDEV
 	  Note that this application programming interface is EXPERIMENTAL
 	  and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
 
+config SPI_LOOPBACK_TEST
+	tristate "spi loopback test framework support"
+	depends on m
+	help
+	  This enables the SPI loopback testing framework driver
+
+	  primarily used for development of spi_master drivers
+	  and to detect regressions
+
 config SPI_TLE62X0
 	tristate "Infineon TLE62X0 (for power switching)"
 	depends on SYSFS

drivers/spi/Makefile

@@ -8,6 +8,7 @@ ccflags-$(CONFIG_SPI_DEBUG) := -DDEBUG
 # config declarations into driver model code
 obj-$(CONFIG_SPI_MASTER)		+= spi.o
 obj-$(CONFIG_SPI_SPIDEV)		+= spidev.o
+obj-$(CONFIG_SPI_LOOPBACK_TEST)		+= spi-loopback-test.o
 
 # SPI master controller drivers (bus)
 obj-$(CONFIG_SPI_ALTERA)		+= spi-altera.o

drivers/spi/spi-bcm63xx.c

@@ -207,6 +207,9 @@ static void bcm63xx_spi_setup_transfer(struct spi_device *spi,
 	u8 clk_cfg, reg;
 	int i;
 
+	/* Default to lowest clock configuration */
+	clk_cfg = SPI_CLK_0_391MHZ;
+
 	/* Find the closest clock configuration */
 	for (i = 0; i < SPI_CLK_MASK; i++) {
 		if (t->speed_hz >= bcm63xx_spi_freq_table[i][0]) {
@@ -215,10 +218,6 @@ static void bcm63xx_spi_setup_transfer(struct spi_device *spi,
 		}
 	}
 
-	/* No matching configuration found, default to lowest */
-	if (i == SPI_CLK_MASK)
-		clk_cfg = SPI_CLK_0_391MHZ;
-
 	/* clear existing clock configuration bits of the register */
 	reg = bcm_spi_readb(bs, SPI_CLK_CFG);
 	reg &= ~SPI_CLK_MASK;

drivers/spi/spi-butterfly.c

@@ -27,7 +27,6 @@
 
 #include <linux/mtd/partitions.h>
 
-
 /*
  * This uses SPI to talk with an "AVR Butterfly", which is a $US20 card
  * with a battery powered AVR microcontroller and lots of goodies.  You
@@ -37,7 +36,6 @@
  * and use this custom parallel port cable.
  */
 
-
 /* DATA output bits (pins 2..9 == D0..D7) */
 #define	butterfly_nreset (1 << 1)		/* pin 3 */
 
@@ -52,14 +50,11 @@
 /* CONTROL output bits */
 #define	spi_cs_bit	PARPORT_CONTROL_SELECT	/* pin 17 */
 
-
-
 static inline struct butterfly *spidev_to_pp(struct spi_device *spi)
 {
 	return spi->controller_data;
 }
 
-
 struct butterfly {
 	/* REVISIT ... for now, this must be first */
 	struct spi_bitbang	bitbang;
@@ -140,7 +135,6 @@ static void butterfly_chipselect(struct spi_device *spi, int value)
 	parport_frob_control(pp->port, spi_cs_bit, value ? spi_cs_bit : 0);
 }
 
-
 /* we only needed to implement one mode here, and choose SPI_MODE_0 */
 
 #define spidelay(X)	do { } while (0)
@@ -149,9 +143,8 @@ static void butterfly_chipselect(struct spi_device *spi, int value)
 #include "spi-bitbang-txrx.h"
 
 static u32
-butterfly_txrx_word_mode0(struct spi_device *spi,
-		unsigned nsecs,
-		u32 word, u8 bits)
+butterfly_txrx_word_mode0(struct spi_device *spi, unsigned nsecs, u32 word,
+			  u8 bits)
 {
 	return bitbang_txrx_be_cpha0(spi, nsecs, 0, 0, word, bits);
 }
@@ -186,7 +179,6 @@ static struct flash_platform_data flash = {
 	.nr_parts	= ARRAY_SIZE(partitions),
 };
 
-
 /* REVISIT remove this ugly global and its "only one" limitation */
 static struct butterfly *butterfly;
 
@@ -197,6 +189,7 @@ static void butterfly_attach(struct parport *p)
 	struct butterfly	*pp;
 	struct spi_master	*master;
 	struct device		*dev = p->physport->dev;
+	struct pardev_cb	butterfly_cb;
 
 	if (butterfly || !dev)
 		return;
@@ -229,9 +222,9 @@ static void butterfly_attach(struct parport *p)
 	 * parport hookup
 	 */
 	pp->port = p;
-	pd = parport_register_device(p, "spi_butterfly",
-			NULL, NULL, NULL,
-			0 /* FLAGS */, pp);
+	memset(&butterfly_cb, 0, sizeof(butterfly_cb));
+	butterfly_cb.private = pp;
+	pd = parport_register_dev_model(p, "spi_butterfly", &butterfly_cb, 0);
 	if (!pd) {
 		status = -ENOMEM;
 		goto clean0;
@@ -262,7 +255,6 @@ static void butterfly_attach(struct parport *p)
 	parport_write_data(pp->port, pp->lastbyte);
 	msleep(100);
 
-
 	/*
 	 * Start SPI ... for now, hide that we're two physical busses.
 	 */
@@ -283,7 +275,7 @@ static void butterfly_attach(struct parport *p)
 	pp->dataflash = spi_new_device(pp->bitbang.master, &pp->info[0]);
 	if (pp->dataflash)
 		pr_debug("%s: dataflash at %s\n", p->name,
-				dev_name(&pp->dataflash->dev));
+			 dev_name(&pp->dataflash->dev));
 
 	pr_info("%s: AVR Butterfly\n", p->name);
 	butterfly = pp;
@@ -297,7 +289,7 @@ static void butterfly_attach(struct parport *p)
 clean1:
 	parport_unregister_device(pd);
 clean0:
-	(void) spi_master_put(pp->bitbang.master);
+	spi_master_put(pp->bitbang.master);
 done:
 	pr_debug("%s: butterfly probe, fail %d\n", p->name, status);
 }
@@ -325,16 +317,16 @@ static void butterfly_detach(struct parport *p)
 	parport_release(pp->pd);
 	parport_unregister_device(pp->pd);
 
-	(void) spi_master_put(pp->bitbang.master);
+	spi_master_put(pp->bitbang.master);
 }
 
 static struct parport_driver butterfly_driver = {
 	.name =		"spi_butterfly",
-	.attach =	butterfly_attach,
+	.match_port =	butterfly_attach,
 	.detach =	butterfly_detach,
+	.devmodel = true,
 };
 
-
 static int __init butterfly_init(void)
 {
 	return parport_register_driver(&butterfly_driver);

drivers/spi/spi-cadence.c

@@ -617,8 +617,7 @@ static int cdns_spi_remove(struct platform_device *pdev)
  */
 static int __maybe_unused cdns_spi_suspend(struct device *dev)
 {
-	struct platform_device *pdev = container_of(dev,
-			struct platform_device, dev);
+	struct platform_device *pdev = to_platform_device(dev);
 	struct spi_master *master = platform_get_drvdata(pdev);
 	struct cdns_spi *xspi = spi_master_get_devdata(master);
 
@@ -641,8 +640,7 @@ static int __maybe_unused cdns_spi_suspend(struct device *dev)
  */
 static int __maybe_unused cdns_spi_resume(struct device *dev)
 {
-	struct platform_device *pdev = container_of(dev,
-			struct platform_device, dev);
+	struct platform_device *pdev = to_platform_device(dev);
 	struct spi_master *master = platform_get_drvdata(pdev);
 	struct cdns_spi *xspi = spi_master_get_devdata(master);
 	int ret = 0;

drivers/spi/spi-davinci.c

@@ -477,33 +477,33 @@ static int davinci_spi_check_error(struct davinci_spi *dspi, int int_status)
 	struct device *sdev = dspi->bitbang.master->dev.parent;
 
 	if (int_status & SPIFLG_TIMEOUT_MASK) {
-		dev_dbg(sdev, "SPI Time-out Error\n");
+		dev_err(sdev, "SPI Time-out Error\n");
 		return -ETIMEDOUT;
 	}
 	if (int_status & SPIFLG_DESYNC_MASK) {
-		dev_dbg(sdev, "SPI Desynchronization Error\n");
+		dev_err(sdev, "SPI Desynchronization Error\n");
 		return -EIO;
 	}
 	if (int_status & SPIFLG_BITERR_MASK) {
-		dev_dbg(sdev, "SPI Bit error\n");
+		dev_err(sdev, "SPI Bit error\n");
 		return -EIO;
 	}
 
 	if (dspi->version == SPI_VERSION_2) {
 		if (int_status & SPIFLG_DLEN_ERR_MASK) {
-			dev_dbg(sdev, "SPI Data Length Error\n");
+			dev_err(sdev, "SPI Data Length Error\n");
 			return -EIO;
 		}
 		if (int_status & SPIFLG_PARERR_MASK) {
-			dev_dbg(sdev, "SPI Parity Error\n");
+			dev_err(sdev, "SPI Parity Error\n");
 			return -EIO;
 		}
 		if (int_status & SPIFLG_OVRRUN_MASK) {
-			dev_dbg(sdev, "SPI Data Overrun error\n");
+			dev_err(sdev, "SPI Data Overrun error\n");
 			return -EIO;
 		}
 		if (int_status & SPIFLG_BUF_INIT_ACTIVE_MASK) {
-			dev_dbg(sdev, "SPI Buffer Init Active\n");
+			dev_err(sdev, "SPI Buffer Init Active\n");
 			return -EBUSY;
 		}
 	}
@@ -703,7 +703,8 @@ static int davinci_spi_bufs(struct spi_device *spi, struct spi_transfer *t)
 
 	/* Wait for the transfer to complete */
 	if (spicfg->io_type != SPI_IO_TYPE_POLL) {
-		wait_for_completion_interruptible(&(dspi->done));
+		if (wait_for_completion_timeout(&dspi->done, HZ) == 0)
+			errors = SPIFLG_TIMEOUT_MASK;
 	} else {
 		while (dspi->rcount > 0 || dspi->wcount > 0) {
 			errors = davinci_spi_process_events(dspi);

drivers/spi/spi-dw-mid.c

@@ -283,7 +283,7 @@ static void mid_spi_dma_stop(struct dw_spi *dws)
 	}
 }
 
-static struct dw_spi_dma_ops mid_dma_ops = {
+static const struct dw_spi_dma_ops mid_dma_ops = {
 	.dma_init	= mid_spi_dma_init,
 	.dma_exit	= mid_spi_dma_exit,
 	.dma_setup	= mid_spi_dma_setup,

drivers/spi/spi-dw.c

@@ -425,7 +425,7 @@ static int dw_spi_setup(struct spi_device *spi)
 		chip->type = chip_info->type;
 	}
 
-	chip->tmode = 0; /* Tx & Rx */
+	chip->tmode = SPI_TMOD_TR;
 
 	if (gpio_is_valid(spi->cs_gpio)) {
 		ret = gpio_direction_output(spi->cs_gpio,