Merge tag 'char-misc-3.6' of git://git.kernel.org/pub/scm/linux/kerne…

…l/git/gregkh/char-misc

Pull char/misc driver merge from Greg Kroah-Hartman:
 "Here is the "big" char/misc driver tree update for the 3.7-rc1 merge
  window.

  Nothing major, just a number of driver updates and fixes, all of which
  have been in the linux-next releases for a while now either in my
  tree, or in Andrew's (the lis3l driver changes came from his tree last
  week).

  Signed-off-by: Greg Kroah-Hartman <[email protected]>"

* tag 'char-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (52 commits)
  drivers/misc/lis3lv02d/lis3lv02d_i2c.c: add lis3lv02d device tree init
  drivers/misc/lis3lv02d/lis3lv02d_spi.c: add lis3lv02d device tree init
  drivers/misc/lis3lv02d: remove lis3lv02d driver DT init
  drivers/misc/lis3lv02d/lis3lv02d_spi.c: add DT matching table passthru code
  drivers/misc/lis3lv02d: add generic DT matching code
  lis3lv02d: fix some comments specific to lis331dlh driver
  MISC: hpilo, remove pci_disable_device
  pcmcia: synclink_cs: fix potential tty NULL dereference
  drivers/char/mmtimer.c: Remove useless kfree
  drivers/char: removes unnecessary semicolon
  char/misc: remove CONFIG_EXPERIMENTAL dependencies
  mei: don't print buffer as a string
  mei: struct mei_message_data doesn't have to be packed
  mei: add error messages for open count errors
  misc: use module_spi_driver
  tifm: use module_pci_driver
  misc/at25, dt: Improve at25 SPI eeprom device tree bindings.
  mei: add lynx point pci device ids
  mei: fix max number of open handles
  mei: rename struct pci_dev *mei_device to mei_pdev
  ...

Documentation/devicetree/bindings/misc/at25.txt

@@ -1,21 +1,35 @@
-Atmel AT25 eeprom
+EEPROMs (SPI) compatible with Atmel at25.
 
 Required properties:
 - compatible : "atmel,at25".
 - reg : chip select number
 - spi-max-frequency : max spi frequency to use
+- pagesize : size of the eeprom page
+- size : total eeprom size in bytes
+- address-width : number of address bits (one of 8, 16, or 24)
 
+Optional properties:
+- spi-cpha : SPI shifted clock phase, as per spi-bus bindings.
+- spi-cpol : SPI inverse clock polarity, as per spi-bus bindings.
+- read-only : this parameter-less property disables writes to the eeprom
+
+Obsolete legacy properties are can be used in place of "size", "pagesize",
+"address-width", and "read-only":
 - at25,byte-len : total eeprom size in bytes
 - at25,addr-mode : addr-mode flags, as defined in include/linux/spi/eeprom.h
 - at25,page-size : size of the eeprom page
 
-Examples:
-at25@0 {
-	compatible = "atmel,at25";
-	reg = <0>
-	spi-max-frequency = <5000000>;
+Additional compatible properties are also allowed.
+
+Example:
+	at25@0 {
+		compatible = "atmel,at25", "st,m95256";
+		reg = <0>
+		spi-max-frequency = <5000000>;
+		spi-cpha;
+		spi-cpol;
 
-	at25,byte-len = <0x8000>;
-	at25,addr-mode = <2>;
-	at25,page-size = <64>;
-};
+		pagesize = <64>;
+		size = <32768>;
+		address-width = <16>;
+	};

Documentation/devicetree/bindings/misc/lis302.txt

@@ -0,0 +1,112 @@
+LIS302 accelerometer devicetree bindings
+
+This device is matched via its bus drivers, and has a number of properties
+that apply in on the generic device (independent from the bus).
+
+
+Required properties for the SPI bindings:
+ - compatible: 		should be set to "st,lis3lv02d_spi"
+ - reg:			the chipselect index
+ - spi-max-frequency:	maximal bus speed, should be set to 1000000 unless
+			constrained by external circuitry
+ - interrupts:		the interrupt generated by the device
+
+Required properties for the I2C bindings:
+ - compatible:		should be set to "st,lis3lv02d"
+ - reg:			i2c slave address
+ - Vdd-supply:		The input supply for Vdd
+ - Vdd_IO-supply:	The input supply for Vdd_IO
+
+
+Optional properties for all bus drivers:
+
+ - st,click-single-{x,y,z}:	if present, tells the device to issue an
+				interrupt on single click events on the
+				x/y/z axis.
+ - st,click-double-{x,y,z}:	if present, tells the device to issue an
+				interrupt on double click events on the
+				x/y/z axis.
+ - st,click-thresh-{x,y,z}:	set the x/y/z axis threshold
+ - st,click-click-time-limit:	click time limit, from 0 to 127.5msec
+				with step of 0.5 msec
+ - st,click-latency:		click latency, from 0 to 255 msec with
+				step of 1 msec.
+ - st,click-window:		click window, from 0 to 255 msec with
+				step of 1 msec.
+ - st,irq{1,2}-disable:		disable IRQ 1/2
+ - st,irq{1,2}-ff-wu-1:		raise IRQ 1/2 on FF_WU_1 condition
+ - st,irq{1,2}-ff-wu-2:		raise IRQ 1/2 on FF_WU_2 condition
+ - st,irq{1,2}-data-ready:	raise IRQ 1/2 on data ready contition
+ - st,irq{1,2}-click:		raise IRQ 1/2 on click condition
+ - st,irq-open-drain:		consider IRQ lines open-drain
+ - st,irq-active-low:		make IRQ lines active low
+ - st,wu-duration-1:		duration register for Free-Fall/Wake-Up
+				interrupt 1
+ - st,wu-duration-2:		duration register for Free-Fall/Wake-Up
+				interrupt 2
+ - st,wakeup-{x,y,z}-{lo,hi}:	set wakeup condition on x/y/z axis for
+				upper/lower limit
+ - st,highpass-cutoff-hz=:	1, 2, 4 or 8 for 1Hz, 2Hz, 4Hz or 8Hz of
+				highpass cut-off frequency
+ - st,hipass{1,2}-disable:	disable highpass 1/2.
+ - st,default-rate=:		set the default rate
+ - st,axis-{x,y,z}=:		set the axis to map to the three coordinates
+ - st,{min,max}-limit-{x,y,z}	set the min/max limits for x/y/z axis
+				(used by self-test)
+
+
+Example for a SPI device node:
+
+	lis302@0 {
+		compatible = "st,lis302dl-spi";
+		reg = <0>;
+		spi-max-frequency = <1000000>;
+		interrupt-parent = <&gpio>;
+		interrupts = <104 0>;
+
+		st,click-single-x;
+		st,click-single-y;
+		st,click-single-z;
+		st,click-thresh-x = <10>;
+		st,click-thresh-y = <10>;
+		st,click-thresh-z = <10>;
+		st,irq1-click;
+		st,irq2-click;
+		st,wakeup-x-lo;
+		st,wakeup-x-hi;
+		st,wakeup-y-lo;
+		st,wakeup-y-hi;
+		st,wakeup-z-lo;
+		st,wakeup-z-hi;
+	};
+
+Example for a I2C device node:
+
+	lis331dlh: lis331dlh@18 {
+		compatible = "st,lis331dlh", "st,lis3lv02d";
+		reg = <0x18>;
+		Vdd-supply = <&lis3_reg>;
+		Vdd_IO-supply = <&lis3_reg>;
+
+		st,click-single-x;
+		st,click-single-y;
+		st,click-single-z;
+		st,click-thresh-x = <10>;
+		st,click-thresh-y = <10>;
+		st,click-thresh-z = <10>;
+		st,irq1-click;
+		st,irq2-click;
+		st,wakeup-x-lo;
+		st,wakeup-x-hi;
+		st,wakeup-y-lo;
+		st,wakeup-y-hi;
+		st,wakeup-z-lo;
+		st,wakeup-z-hi;
+		st,min-limit-x = <120>;
+		st,min-limit-y = <120>;
+		st,min-limit-z = <140>;
+		st,max-limit-x = <550>;
+		st,max-limit-y = <550>;
+		st,max-limit-z = <750>;
+	};
+

Documentation/devicetree/bindings/w1/w1-gpio.txt

@@ -0,0 +1,22 @@
+w1-gpio devicetree bindings
+
+Required properties:
+
+ - compatible: "w1-gpio"
+ - gpios: one or two GPIO specs:
+		- the first one is used as data I/O pin
+		- the second one is optional. If specified, it is used as
+		  enable pin for an external pin pullup.
+
+Optional properties:
+
+ - linux,open-drain: if specified, the data pin is considered in
+		     open-drain mode.
+
+Examples:
+
+	onewire@0 {
+		compatible = "w1-gpio";
+		gpios = <&gpio 126 0>, <&gpio 105 0>;
+	};
+

Documentation/misc-devices/lis3lv02d

@@ -4,7 +4,8 @@ Kernel driver lis3lv02d
 Supported chips:
 
   * STMicroelectronics LIS3LV02DL, LIS3LV02DQ (12 bits precision)
-  * STMicroelectronics LIS302DL, LIS3L02DQ, LIS331DL (8 bits)
+  * STMicroelectronics LIS302DL, LIS3L02DQ, LIS331DL (8 bits) and
+    LIS331DLH (16 bits)
 
 Authors:
         Yan Burman <[email protected]>

drivers/char/Kconfig

@@ -418,8 +418,8 @@ config APPLICOM
 	  If unsure, say N.
 
 config SONYPI
-	tristate "Sony Vaio Programmable I/O Control Device support (EXPERIMENTAL)"
-	depends on EXPERIMENTAL && X86 && PCI && INPUT && !64BIT
+	tristate "Sony Vaio Programmable I/O Control Device support"
+	depends on X86 && PCI && INPUT && !64BIT
 	---help---
 	  This driver enables access to the Sony Programmable I/O Control
 	  Device which can be found in many (all ?) Sony Vaio laptops.
@@ -566,7 +566,7 @@ source "drivers/char/tpm/Kconfig"
 
 config TELCLOCK
 	tristate "Telecom clock driver for ATCA SBC"
-	depends on EXPERIMENTAL && X86
+	depends on X86
 	default n
 	help
 	  The telecom clock device is specific to the MPCBL0010 and MPCBL0050

drivers/char/mmtimer.c

@@ -826,7 +826,7 @@ static int __init mmtimer_init(void)
 
 	/* Allocate list of node ptrs to mmtimer_t's */
 	timers = kzalloc(sizeof(struct mmtimer_node)*maxn, GFP_KERNEL);
-	if (timers == NULL) {
+	if (!timers) {
 		printk(KERN_ERR "%s: failed to allocate memory for device\n",
 				MMTIMER_NAME);
 		goto out3;
@@ -848,7 +848,6 @@ static int __init mmtimer_init(void)
 	return 0;
 
 out3:
-	kfree(timers);
 	misc_deregister(&mmtimer_miscdev);
 out2:
 	free_irq(SGI_MMTIMER_VECTOR, NULL);

drivers/char/nwbutton.c

@@ -93,9 +93,9 @@ int button_del_callback (void (*callback) (void))
 			button_callback_list [lp].count = 0;
 			callback_count--;
 			return 0;
-		};
+		}
 		lp--;
-	};
+	}
 	return -EINVAL;
 }
 

drivers/char/pcmcia/synclink_cs.c

@@ -891,6 +891,14 @@ static void rx_ready_async(MGSLPC_INFO *info, int tcd, struct tty_struct *tty)
 	int work = 0;
  	struct mgsl_icount *icount = &info->icount;
 
+	if (!tty) {
+		/* tty is not available anymore */
+		issue_command(info, CHA, CMD_RXRESET);
+		if (debug_level >= DEBUG_LEVEL_ISR)
+			printk("%s(%d):rx_ready_async(tty=NULL)\n",__FILE__,__LINE__);
+		return;
+	}
+
 	if (tcd) {
 		/* early termination, get FIFO count from RBCL register */
 		fifo_count = (unsigned char)(read_reg(info, CHA+RBCL) & 0x1f);
@@ -980,7 +988,7 @@ static void tx_done(MGSLPC_INFO *info, struct tty_struct *tty)
 	else
 #endif
 	{
-		if (tty->stopped || tty->hw_stopped) {
+		if (tty && (tty->stopped || tty->hw_stopped)) {
 			tx_stop(info);
 			return;
 		}
@@ -1000,7 +1008,7 @@ static void tx_ready(MGSLPC_INFO *info, struct tty_struct *tty)
 		if (!info->tx_active)
 			return;
 	} else {
-		if (tty->stopped || tty->hw_stopped) {
+		if (tty && (tty->stopped || tty->hw_stopped)) {
 			tx_stop(info);
 			return;
 		}
@@ -1050,13 +1058,12 @@ static void cts_change(MGSLPC_INFO *info, struct tty_struct *tty)
 	wake_up_interruptible(&info->status_event_wait_q);
 	wake_up_interruptible(&info->event_wait_q);
 
-	if (info->port.flags & ASYNC_CTS_FLOW) {
+	if (tty && (info->port.flags & ASYNC_CTS_FLOW)) {
 		if (tty->hw_stopped) {
 			if (info->serial_signals & SerialSignal_CTS) {
 				if (debug_level >= DEBUG_LEVEL_ISR)
 					printk("CTS tx start...");
-				if (tty)
-					tty->hw_stopped = 0;
+				tty->hw_stopped = 0;
 				tx_start(info, tty);
 				info->pending_bh |= BH_TRANSMIT;
 				return;
@@ -1065,8 +1072,7 @@ static void cts_change(MGSLPC_INFO *info, struct tty_struct *tty)
 			if (!(info->serial_signals & SerialSignal_CTS)) {
 				if (debug_level >= DEBUG_LEVEL_ISR)
 					printk("CTS tx stop...");
-				if (tty)
-					tty->hw_stopped = 1;
+				tty->hw_stopped = 1;
 				tx_stop(info);
 			}
 		}

drivers/char/ppdev.c

@@ -783,7 +783,8 @@ static int __init ppdev_init (void)
 		err = PTR_ERR(ppdev_class);
 		goto out_chrdev;
 	}
-	if (parport_register_driver(&pp_driver)) {
+	err = parport_register_driver(&pp_driver);
+	if (err < 0) {
 		printk (KERN_WARNING CHRDEV ": unable to register with parport\n");
 		goto out_class;
 	}

drivers/char/rtc.c

@@ -411,7 +411,7 @@ static int rtc_do_ioctl(unsigned int cmd, unsigned long arg, int kernel)
 		case RTC_IRQP_READ:
 		case RTC_IRQP_SET:
 			return -EINVAL;
-		};
+		}
 	}
 #endif
 

drivers/char/tlclk.c

@@ -784,8 +784,10 @@ static int __init tlclk_init(void)
 	}
 	tlclk_major = ret;
 	alarm_events = kzalloc( sizeof(struct tlclk_alarms), GFP_KERNEL);
-	if (!alarm_events)
+	if (!alarm_events) {
+		ret = -ENOMEM;
 		goto out1;
+	}
 
 	/* Read telecom clock IRQ number (Set by BIOS) */
 	if (!request_region(TLCLK_BASE, 8, "telco_clock")) {

drivers/char/virtio_console.c

@@ -1941,7 +1941,17 @@ static int __init init(void)
 	INIT_LIST_HEAD(&pdrvdata.consoles);
 	INIT_LIST_HEAD(&pdrvdata.portdevs);
 
-	return register_virtio_driver(&virtio_console);
+	err = register_virtio_driver(&virtio_console);
+	if (err < 0) {
+		pr_err("Error %d registering virtio driver\n", err);
+		goto free;
+	}
+	return 0;
+free:
+	if (pdrvdata.debugfs_dir)
+		debugfs_remove_recursive(pdrvdata.debugfs_dir);
+	class_destroy(pdrvdata.class);
+	return err;
 }
 
 static void __exit fini(void)

drivers/misc/Kconfig

@@ -105,7 +105,7 @@ config ATMEL_TCB_CLKSRC_BLOCK
 
 config IBM_ASM
 	tristate "Device driver for IBM RSA service processor"
-	depends on X86 && PCI && INPUT && EXPERIMENTAL
+	depends on X86 && PCI && INPUT
 	---help---
 	  This option enables device driver support for in-band access to the
 	  IBM RSA (Condor) service processor in eServer xSeries systems.
@@ -162,8 +162,8 @@ config SGI_IOC4
 	  Otherwise say N.
 
 config TIFM_CORE
-	tristate "TI Flash Media interface support (EXPERIMENTAL)"
-	depends on EXPERIMENTAL && PCI
+	tristate "TI Flash Media interface support"
+	depends on PCI
 	help
 	  If you want support for Texas Instruments(R) Flash Media adapters
 	  you should select this option and then also choose an appropriate
@@ -178,8 +178,8 @@ config TIFM_CORE
 	  be called tifm_core.
 
 config TIFM_7XX1
-	tristate "TI Flash Media PCI74xx/PCI76xx host adapter support (EXPERIMENTAL)"
-	depends on PCI && TIFM_CORE && EXPERIMENTAL
+	tristate "TI Flash Media PCI74xx/PCI76xx host adapter support"
+	depends on PCI && TIFM_CORE
 	default TIFM_CORE
 	help
 	  This option enables support for Texas Instruments(R) PCI74xx and
@@ -192,7 +192,7 @@ config TIFM_7XX1
 
 config ICS932S401
 	tristate "Integrated Circuits ICS932S401"
-	depends on I2C && EXPERIMENTAL
+	depends on I2C
 	help
 	  If you say yes here you get support for the Integrated Circuits
 	  ICS932S401 clock control chips.
@@ -398,7 +398,7 @@ config EP93XX_PWM
 
 config DS1682
 	tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm"
-	depends on I2C && EXPERIMENTAL
+	depends on I2C
 	help
 	  If you say yes here you get support for Dallas Semiconductor
 	  DS1682 Total Elapsed Time Recorder.