Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/…

…git/sameo/mfd-2.6

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
  rtc: max8925: Add function to work as wakeup source
  mfd: Add pm ops to max8925
  mfd: Convert aat2870 to dev_pm_ops
  mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
  mfd: Introduce missing kfree in 88pm860x probe routine
  mfd: Add S5M series configuration
  mfd: Add s5m series irq driver
  mfd: Add S5M core driver
  mfd: Improve mc13xxx dt binding document
  mfd: Fix stmpe section mismatch
  mfd: Fix stmpe build warning
  mfd: Fix STMPE I2c build failure
  mfd: Constify aat2870-core i2c_device_id table
  gpio: Add support for stmpe variant 801
  mfd: Add support for stmpe variant 801
  mfd: Add support for stmpe variant 610
  mfd: Add support for STMPE SPI interface
  mfd: Separate out STMPE controller and interface specific code
  misc: Remove max8997-muic sysfs attributes
  mfd: Remove unused wm831x_irq_data_to_mask_reg()
  ...

Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.

Documentation/devicetree/bindings/mfd/mc13xxx.txt

@@ -0,0 +1,78 @@
+* Freescale MC13783/MC13892 Power Management Integrated Circuit (PMIC)
+
+Required properties:
+- compatible : Should be "fsl,mc13783" or "fsl,mc13892"
+
+Optional properties:
+- fsl,mc13xxx-uses-adc : Indicate the ADC is being used
+- fsl,mc13xxx-uses-codec : Indicate the Audio Codec is being used
+- fsl,mc13xxx-uses-rtc : Indicate the RTC is being used
+- fsl,mc13xxx-uses-touch : Indicate the touchscreen controller is being used
+
+Sub-nodes:
+- regulators : Contain the regulator nodes.  The MC13892 regulators are
+  bound using their names as listed below with their registers and bits
+  for enabling.
+
+    vcoincell : regulator VCOINCELL (register 13, bit 23)
+    sw1       : regulator SW1	    (register 24, bit 0)
+    sw2       : regulator SW2	    (register 25, bit 0)
+    sw3       : regulator SW3	    (register 26, bit 0)
+    sw4       : regulator SW4	    (register 27, bit 0)
+    swbst     : regulator SWBST	    (register 29, bit 20)
+    vgen1     : regulator VGEN1	    (register 32, bit 0)
+    viohi     : regulator VIOHI	    (register 32, bit 3)
+    vdig      : regulator VDIG	    (register 32, bit 9)
+    vgen2     : regulator VGEN2	    (register 32, bit 12)
+    vpll      : regulator VPLL	    (register 32, bit 15)
+    vusb2     : regulator VUSB2	    (register 32, bit 18)
+    vgen3     : regulator VGEN3	    (register 33, bit 0)
+    vcam      : regulator VCAM	    (register 33, bit 6)
+    vvideo    : regulator VVIDEO    (register 33, bit 12)
+    vaudio    : regulator VAUDIO    (register 33, bit 15)
+    vsd       : regulator VSD	    (register 33, bit 18)
+    gpo1      : regulator GPO1	    (register 34, bit 6)
+    gpo2      : regulator GPO2	    (register 34, bit 8)
+    gpo3      : regulator GPO3	    (register 34, bit 10)
+    gpo4      : regulator GPO4	    (register 34, bit 12)
+    pwgt1spi  : regulator PWGT1SPI  (register 34, bit 15)
+    pwgt2spi  : regulator PWGT2SPI  (register 34, bit 16)
+    vusb      : regulator VUSB	    (register 50, bit 3)
+
+  The bindings details of individual regulator device can be found in:
+  Documentation/devicetree/bindings/regulator/regulator.txt
+
+Examples:
+
+ecspi@70010000 { /* ECSPI1 */
+	fsl,spi-num-chipselects = <2>;
+	cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */
+		   <&gpio3 25 0>; /* GPIO4_25 */
+	status = "okay";
+
+	pmic: mc13892@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mc13892";
+		spi-max-frequency = <6000000>;
+		reg = <0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <8>;
+
+		regulators {
+			sw1_reg: mc13892__sw1 {
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <1375000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw2_reg: mc13892__sw2 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};

Documentation/devicetree/bindings/mfd/twl-familly.txt

@@ -0,0 +1,47 @@
+Texas Instruments TWL family
+
+The TWLs are Integrated Power Management Chips.
+Some version might contain much more analog function like
+USB transceiver or Audio amplifier.
+These chips are connected to an i2c bus.
+
+
+Required properties:
+- compatible : Must be "ti,twl4030";
+  For Integrated power-management/audio CODEC device used in OMAP3
+  based boards
+- compatible : Must be "ti,twl6030";
+  For Integrated power-management used in OMAP4 based boards
+- interrupts : This i2c device has an IRQ line connected to the main SoC
+- interrupt-controller : Since the twl support several interrupts internally,
+  it is considered as an interrupt controller cascaded to the SoC one.
+- #interrupt-cells = <1>;
+- interrupt-parent : The parent interrupt controller.
+
+Optional node:
+- Child nodes contain in the twl. The twl family is made of several variants
+  that support a different number of features.
+  The children nodes will thus depend of the capability of the variant.
+
+
+Example:
+/*
+ * Integrated Power Management Chip
+ * http://www.ti.com/lit/ds/symlink/twl6030.pdf
+ */
+twl@48 {
+    compatible = "ti,twl6030";
+    reg = <0x48>;
+    interrupts = <39>; /* IRQ_SYS_1N cascaded to gic */
+    interrupt-controller;
+    #interrupt-cells = <1>;
+    interrupt-parent = <&gic>;
+    #address-cells = <1>;
+    #size-cells = <0>;
+
+    twl_rtc {
+        compatible = "ti,twl_rtc";
+        interrupts = <11>;
+        reg = <0>;
+    };
+};

arch/arm/mach-sa1100/assabet.c

@@ -202,6 +202,7 @@ static struct irda_platform_data assabet_irda_data = {
 static struct mcp_plat_data assabet_mcp_data = {
 	.mccr0		= MCCR0_ADM,
 	.sclk_rate	= 11981000,
+	.codec		= "ucb1x00",
 };
 
 static void __init assabet_init(void)
@@ -252,6 +253,17 @@ static void __init assabet_init(void)
 	sa11x0_register_mtd(&assabet_flash_data, assabet_flash_resources,
 			    ARRAY_SIZE(assabet_flash_resources));
 	sa11x0_register_irda(&assabet_irda_data);
+
+	/*
+	 * Setup the PPC unit correctly.
+	 */
+	PPDR &= ~PPC_RXD4;
+	PPDR |= PPC_TXD4 | PPC_SCLK | PPC_SFRM;
+	PSDR |= PPC_RXD4;
+	PSDR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
+	PPSR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
+
+	ASSABET_BCR_set(ASSABET_BCR_CODEC_RST);
 	sa11x0_register_mcp(&assabet_mcp_data);
 }
 

arch/arm/mach-sa1100/cerf.c

@@ -124,12 +124,23 @@ static void __init cerf_map_io(void)
 static struct mcp_plat_data cerf_mcp_data = {
 	.mccr0		= MCCR0_ADM,
 	.sclk_rate	= 11981000,
+	.codec		= "ucb1x00",
 };
 
 static void __init cerf_init(void)
 {
 	platform_add_devices(cerf_devices, ARRAY_SIZE(cerf_devices));
 	sa11x0_register_mtd(&cerf_flash_data, &cerf_flash_resource, 1);
+
+	/*
+	 * Setup the PPC unit correctly.
+	 */
+	PPDR &= ~PPC_RXD4;
+	PPDR |= PPC_TXD4 | PPC_SCLK | PPC_SFRM;
+	PSDR |= PPC_RXD4;
+	PSDR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
+	PPSR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
+
 	sa11x0_register_mcp(&cerf_mcp_data);
 }
 

arch/arm/mach-sa1100/collie.c

@@ -27,6 +27,7 @@
 #include <linux/timer.h>
 #include <linux/gpio.h>
 #include <linux/pda_power.h>
+#include <linux/mfd/ucb1x00.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
@@ -85,10 +86,15 @@ static struct scoop_pcmcia_config collie_pcmcia_config = {
 	.num_devs	= 1,
 };
 
+static struct ucb1x00_plat_data collie_ucb1x00_data = {
+	.gpio_base	= COLLIE_TC35143_GPIO_BASE,
+};
+
 static struct mcp_plat_data collie_mcp_data = {
 	.mccr0		= MCCR0_ADM | MCCR0_ExtClk,
 	.sclk_rate	= 9216000,
-	.gpio_base	= COLLIE_TC35143_GPIO_BASE,
+	.codec		= "ucb1x00",
+	.codec_pdata	= &collie_ucb1x00_data,
 };
 
 /*
@@ -351,6 +357,16 @@ static void __init collie_init(void)
 
 	sa11x0_register_mtd(&collie_flash_data, collie_flash_resources,
 			    ARRAY_SIZE(collie_flash_resources));
+
+	/*
+	 * Setup the PPC unit correctly.
+	 */
+	PPDR &= ~PPC_RXD4;
+	PPDR |= PPC_TXD4 | PPC_SCLK | PPC_SFRM;
+	PSDR |= PPC_RXD4;
+	PSDR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
+	PPSR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
+
 	sa11x0_register_mcp(&collie_mcp_data);
 
 	sharpsl_save_param();

arch/arm/mach-sa1100/generic.c

@@ -217,10 +217,15 @@ static struct platform_device sa11x0uart3_device = {
 static struct resource sa11x0mcp_resources[] = {
 	[0] = {
 		.start	= __PREG(Ser4MCCR0),
-		.end	= __PREG(Ser4MCCR0) + 0xffff,
+		.end	= __PREG(Ser4MCCR0) + 0x1C - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
+		.start	= __PREG(Ser4MCCR1),
+		.end	= __PREG(Ser4MCCR1) + 0x4 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
 		.start	= IRQ_Ser4MCP,
 		.end	= IRQ_Ser4MCP,
 		.flags	= IORESOURCE_IRQ,

arch/arm/mach-sa1100/include/mach/mcp.h

@@ -17,6 +17,8 @@ struct mcp_plat_data {
 	u32 mccr1;
 	unsigned int sclk_rate;
 	int gpio_base;
+	const char *codec;
+	void *codec_pdata;
 };
 
 #endif

arch/arm/mach-sa1100/lart.c

@@ -24,10 +24,20 @@
 static struct mcp_plat_data lart_mcp_data = {
 	.mccr0		= MCCR0_ADM,
 	.sclk_rate	= 11981000,
+	.codec		= "ucb1x00",
 };
 
 static void __init lart_init(void)
 {
+	/*
+	 * Setup the PPC unit correctly.
+	 */
+	PPDR &= ~PPC_RXD4;
+	PPDR |= PPC_TXD4 | PPC_SCLK | PPC_SFRM;
+	PSDR |= PPC_RXD4;
+	PSDR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
+	PPSR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
+
 	sa11x0_register_mcp(&lart_mcp_data);
 }
 

arch/arm/mach-sa1100/shannon.c

@@ -55,11 +55,22 @@ static struct resource shannon_flash_resource = {
 static struct mcp_plat_data shannon_mcp_data = {
 	.mccr0		= MCCR0_ADM,
 	.sclk_rate	= 11981000,
+	.codec		= "ucb1x00",
 };
 
 static void __init shannon_init(void)
 {
 	sa11x0_register_mtd(&shannon_flash_data, &shannon_flash_resource, 1);
+
+	/*
+	 * Setup the PPC unit correctly.
+	 */
+	PPDR &= ~PPC_RXD4;
+	PPDR |= PPC_TXD4 | PPC_SCLK | PPC_SFRM;
+	PSDR |= PPC_RXD4;
+	PSDR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
+	PPSR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
+
 	sa11x0_register_mcp(&shannon_mcp_data);
 }
 

arch/arm/mach-sa1100/simpad.c

@@ -14,6 +14,7 @@
 #include <linux/mtd/partitions.h>
 #include <linux/io.h>
 #include <linux/gpio.h>
+#include <linux/mfd/ucb1x00.h>
 
 #include <asm/irq.h>
 #include <mach/hardware.h>
@@ -187,10 +188,15 @@ static struct resource simpad_flash_resources [] = {
 	}
 };
 
+static struct ucb1x00_plat_data simpad_ucb1x00_data = {
+	.gpio_base	= SIMPAD_UCB1X00_GPIO_BASE,
+};
+
 static struct mcp_plat_data simpad_mcp_data = {
 	.mccr0		= MCCR0_ADM,
 	.sclk_rate	= 11981000,
-	.gpio_base	= SIMPAD_UCB1X00_GPIO_BASE,
+	.codec		= "ucb1300",
+	.codec_pdata	= &simpad_ucb1x00_data,
 };
 
 
@@ -378,6 +384,16 @@ static int __init simpad_init(void)
 
 	sa11x0_register_mtd(&simpad_flash_data, simpad_flash_resources,
 			      ARRAY_SIZE(simpad_flash_resources));
+
+	/*
+	 * Setup the PPC unit correctly.
+	 */
+	PPDR &= ~PPC_RXD4;
+	PPDR |= PPC_TXD4 | PPC_SCLK | PPC_SFRM;
+	PSDR |= PPC_RXD4;
+	PSDR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
+	PPSR &= ~(PPC_TXD4 | PPC_SCLK | PPC_SFRM);
+
 	sa11x0_register_mcp(&simpad_mcp_data);
 
 	ret = platform_add_devices(devices, ARRAY_SIZE(devices));

arch/arm/mach-ux500/board-mop500.c

@@ -19,11 +19,11 @@
 #include <linux/amba/pl022.h>
 #include <linux/amba/serial.h>
 #include <linux/spi/spi.h>
-#include <linux/mfd/ab8500.h>
+#include <linux/mfd/abx500/ab8500.h>
 #include <linux/regulator/ab8500.h>
 #include <linux/mfd/tc3589x.h>
 #include <linux/mfd/tps6105x.h>
-#include <linux/mfd/ab8500/gpio.h>
+#include <linux/mfd/abx500/ab8500-gpio.h>
 #include <linux/leds-lp5521.h>
 #include <linux/input.h>
 #include <linux/smsc911x.h>

arch/arm/mach-ux500/board-u5500.c

@@ -10,7 +10,7 @@
 #include <linux/amba/bus.h>
 #include <linux/irq.h>
 #include <linux/i2c.h>
-#include <linux/mfd/ab5500/ab5500.h>
+#include <linux/mfd/abx500/ab5500.h>
 
 #include <asm/hardware/gic.h>
 #include <asm/mach/arch.h>

arch/arm/mach-ux500/include/mach/irqs-board-mop500.h

@@ -9,7 +9,7 @@
 #define __MACH_IRQS_BOARD_MOP500_H
 
 /* Number of AB8500 irqs is taken from header file */
-#include <linux/mfd/ab8500.h>
+#include <linux/mfd/abx500/ab8500.h>
 
 #define MOP500_AB8500_IRQ_BASE		IRQ_BOARD_START
 #define MOP500_AB8500_IRQ_END		(MOP500_AB8500_IRQ_BASE \