pata/at91: use newly introduced SMC accessors

pata_at91 driver is broken since faee0cc:
"make smc register base soc independent"
Fix it with newly introduced SMC accessors.

The overall action of removal of at91_sys_read/write will allow
to use the pata_at91 on a single zImage kernel.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Acked-by: Nicolas Ferre <[email protected]>
Cc: [email protected]

drivers/ata/pata_at91.c

@@ -207,11 +207,11 @@ static void set_smc_timing(struct device *dev, struct ata_device *adev,
 {
 	int ret = 0;
 	int use_iordy;
+	struct sam9_smc_config smc;
 	unsigned int t6z;         /* data tristate time in ns */
 	unsigned int cycle;       /* SMC Cycle width in MCK ticks */
 	unsigned int setup;       /* SMC Setup width in MCK ticks */
 	unsigned int pulse;       /* CFIOR and CFIOW pulse width in MCK ticks */
-	unsigned int cs_setup = 0;/* CS4 or CS5 setup width in MCK ticks */
 	unsigned int cs_pulse;    /* CS4 or CS5 pulse width in MCK ticks*/
 	unsigned int tdf_cycles;  /* SMC TDF MCK ticks */
 	unsigned long mck_hz;     /* MCK frequency in Hz */
@@ -244,26 +244,20 @@ static void set_smc_timing(struct device *dev, struct ata_device *adev,
 	}
 
 	dev_dbg(dev, "Use IORDY=%u, TDF Cycles=%u\n", use_iordy, tdf_cycles);
-	info->mode |= AT91_SMC_TDF_(tdf_cycles);
-
-	/* write SMC Setup Register */
-	at91_sys_write(AT91_SMC_SETUP(info->cs),
-			AT91_SMC_NWESETUP_(setup) |
-			AT91_SMC_NRDSETUP_(setup) |
-			AT91_SMC_NCS_WRSETUP_(cs_setup) |
-			AT91_SMC_NCS_RDSETUP_(cs_setup));
-	/* write SMC Pulse Register */
-	at91_sys_write(AT91_SMC_PULSE(info->cs),
-			AT91_SMC_NWEPULSE_(pulse) |
-			AT91_SMC_NRDPULSE_(pulse) |
-			AT91_SMC_NCS_WRPULSE_(cs_pulse) |
-			AT91_SMC_NCS_RDPULSE_(cs_pulse));
-	/* write SMC Cycle Register */
-	at91_sys_write(AT91_SMC_CYCLE(info->cs),
-			AT91_SMC_NWECYCLE_(cycle) |
-			AT91_SMC_NRDCYCLE_(cycle));
-	/* write SMC Mode Register*/
-	at91_sys_write(AT91_SMC_MODE(info->cs), info->mode);
+
+	/* SMC Setup Register */
+	smc.nwe_setup = smc.nrd_setup = setup;
+	smc.ncs_write_setup = smc.ncs_read_setup = 0;
+	/* SMC Pulse Register */
+	smc.nwe_pulse = smc.nrd_pulse = pulse;
+	smc.ncs_write_pulse = smc.ncs_read_pulse = cs_pulse;
+	/* SMC Cycle Register */
+	smc.write_cycle = smc.read_cycle = cycle;
+	/* SMC Mode Register*/
+	smc.tdf_cycles = tdf_cycles;
+	smc.mode = info->mode;
+
+	sam9_smc_configure(0, info->cs, &smc);
 }
 
 static void pata_at91_set_piomode(struct ata_port *ap, struct ata_device *adev)
@@ -288,20 +282,20 @@ static unsigned int pata_at91_data_xfer_noirq(struct ata_device *dev,
 	struct at91_ide_info *info = dev->link->ap->host->private_data;
 	unsigned int consumed;
 	unsigned long flags;
-	unsigned int mode;
+	struct sam9_smc_config smc;
 
 	local_irq_save(flags);
-	mode = at91_sys_read(AT91_SMC_MODE(info->cs));
+	sam9_smc_read_mode(0, info->cs, &smc);
 
 	/* set 16bit mode before writing data */
-	at91_sys_write(AT91_SMC_MODE(info->cs),
-			(mode & ~AT91_SMC_DBW) | AT91_SMC_DBW_16);
+	smc.mode = (smc.mode & ~AT91_SMC_DBW) | AT91_SMC_DBW_16;
+	sam9_smc_write_mode(0, info->cs, &smc);
 
 	consumed = ata_sff_data_xfer(dev, buf, buflen, rw);
 
 	/* restore 8bit mode after data is written */
-	at91_sys_write(AT91_SMC_MODE(info->cs),
-			(mode & ~AT91_SMC_DBW) | AT91_SMC_DBW_8);
+	smc.mode = (smc.mode & ~AT91_SMC_DBW) | AT91_SMC_DBW_8;
+	sam9_smc_write_mode(0, info->cs, &smc);
 
 	local_irq_restore(flags);
 	return consumed;