Merge tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/k…

…ernel/git/helgaas/pci

Pull pci updates from Bjorn Helgaas:
 "Enumeration:

   - Consolidate duplicated 'next function' scanning and extend to allow
     'isolated functions' on s390, similar to existing hypervisors
     (Niklas Schnelle)

  Resource management:
   - Implement pci_iobar_pfn() for sparc, which allows us to remove the
     sparc-specific pci_mmap_page_range() and pci_mmap_resource_range().

     This removes the ability to map the entire PCI I/O space using
     /proc/bus/pci, but we believe that's already been broken since
     v2.6.28 (Arnd Bergmann)

   - Move common PCI definitions to asm-generic/pci.h and rework others
     to be be more specific and more encapsulated in arches that need
     them (Stafford Horne)

  Power management:

   - Convert drivers to new *_PM_OPS macros to avoid need for '#ifdef
     CONFIG_PM_SLEEP' or '__maybe_unused' (Bjorn Helgaas)

  Virtualization:

   - Add ACS quirk for Broadcom BCM5750x multifunction NICs that isolate
     the functions but don't advertise an ACS capability (Pavan Chebbi)

  Error handling:

   - Clear PCI Status register during enumeration in case firmware left
     errors logged (Kai-Heng Feng)

   - When we have native control of AER, enable error reporting for all
     devices that support AER. Previously only a few drivers enabled
     this (Stefan Roese)

   - Keep AER error reporting enabled for switches. Previously we
     enabled this during enumeration but immediately disabled it (Stefan
     Roese)

   - Iterate over error counters instead of error strings to avoid
     printing junk in AER sysfs counters (Mohamed Khalfella)

  ASPM:

   - Remove pcie_aspm_pm_state_change() so ASPM config changes, e.g.,
     via sysfs, are not lost across power state changes (Kai-Heng Feng)

  Endpoint framework:

   - Don't stop an EPC when unbinding an EPF from it (Shunsuke Mie)

  Endpoint embedded DMA controller driver:

   - Simplify and clean up support for the DesignWare embedded DMA
     (eDMA) controller (Frank Li, Serge Semin)

  Broadcom STB PCIe controller driver:

   - Avoid config space accesses when link is down because we can't
     recover from the CPU aborts these cause (Jim Quinlan)

   - Look for power regulators described under Root Ports in DT and
     enable them before scanning the secondary bus (Jim Quinlan)

   - Disable/enable regulators in suspend/resume (Jim Quinlan)

  Freescale i.MX6 PCIe controller driver:

   - Simplify and clean up clock and PHY management (Richard Zhu)

   - Disable/enable regulators in suspend/resume (Richard Zhu)

   - Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu)

   - Allow speeds faster than Gen2 (Richard Zhu)

   - Make link being down a non-fatal error so controller probe doesn't
     fail if there are no Endpoints connected (Richard Zhu)

  Loongson PCIe controller driver:

   - Add ACPI and MCFG support for Loongson LS7A (Huacai Chen)

   - Avoid config reads to non-existent LS2K/LS7A devices because a
     hardware defect causes machine hangs (Huacai Chen)

   - Work around LS7A integrated devices that report incorrect Interrupt
     Pin values (Jianmin Lv)

  Marvell Aardvark PCIe controller driver:

   - Add support for AER and Slot capability on emulated bridge (Pali
     Rohár)

  MediaTek PCIe controller driver:

   - Add Airoha EN7532 to DT binding (John Crispin)

   - Allow building of driver for ARCH_AIROHA (Felix Fietkau)

  MediaTek PCIe Gen3 controller driver:

   - Print decoded LTSSM state when the link doesn't come up (Jianjun
     Wang)

  NVIDIA Tegra194 PCIe controller driver:

   - Convert DT binding to json-schema (Vidya Sagar)

   - Add DT bindings and driver support for Tegra234 Root Port and
     Endpoint mode (Vidya Sagar)

   - Fix some Root Port interrupt handling issues (Vidya Sagar)

   - Set default Max Payload Size to 256 bytes (Vidya Sagar)

   - Fix Data Link Feature capability programming (Vidya Sagar)

   - Extend Endpoint mode support to devices beyond Controller-5 (Vidya
     Sagar)

  Qualcomm PCIe controller driver:

   - Rework clock, reset, PHY power-on ordering to avoid hangs and
     improve consistency (Robert Marko, Christian Marangi)

   - Move pipe_clk handling to PHY drivers (Dmitry Baryshkov)

   - Add IPQ60xx support (Selvam Sathappan Periakaruppan)

   - Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru)

   - Add support for more than 32 MSI interrupts (Dmitry Baryshkov)

  Renesas R-Car PCIe controller driver:

   - Convert DT binding to json-schema (Herve Codina)

   - Add Renesas RZ/N1D (R9A06G032) to rcar-gen2 DT binding and driver
     (Herve Codina)

  Samsung Exynos PCIe controller driver:

   - Fix phy-exynos-pcie driver so it follows the 'phy_init() before
     phy_power_on()' PHY programming model (Marek Szyprowski)

  Synopsys DesignWare PCIe controller driver:

   - Simplify and clean up the DWC core extensively (Serge Semin)

   - Fix an issue with programming the ATU for regions that cross a 4GB
     boundary (Serge Semin)

   - Enable the CDM check if 'snps,enable-cdm-check' exists; previously
     we skipped it if 'num-lanes' was absent (Serge Semin)

   - Allocate a 32-bit DMA-able page to be MSI target instead of using a
     driver data structure that may not be addressable with 32-bit
     address (Will McVicker)

   - Add DWC core support for more than 32 MSI interrupts (Dmitry
     Baryshkov)

  Xilinx Versal CPM PCIe controller driver:

   - Add DT binding and driver support for Versal CPM5 Gen5 Root Port
     (Bharat Kumar Gogada)"

* tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (150 commits)
  PCI: imx6: Support more than Gen2 speed link mode
  PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers
  PCI: imx6: Reformat suspend callback to keep symmetric with resume
  PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier
  PCI: imx6: Disable clocks in reverse order of enable
  PCI: imx6: Do not hide PHY driver callbacks and refine the error handling
  PCI: imx6: Reduce resume time by only starting link if it was up before suspend
  PCI: imx6: Mark the link down as non-fatal error
  PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset()
  PCI: imx6: Turn off regulator when system is in suspend mode
  PCI: imx6: Call host init function directly in resume
  PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks
  PCI: imx6: Propagate .host_init() errors to caller
  PCI: imx6: Collect clock enables in imx6_pcie_clk_enable()
  PCI: imx6: Factor out ref clock disable to match enable
  PCI: imx6: Move imx6_pcie_clk_disable() earlier
  PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier
  PCI: imx6: Move PHY management functions together
  PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier
  PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS()
  ...

Documentation/PCI/pci-iov-howto.rst

@@ -125,14 +125,14 @@ Following piece of code illustrates the usage of the SR-IOV API.
 		...
 	}
 
-	static int dev_suspend(struct pci_dev *dev, pm_message_t state)
+	static int dev_suspend(struct device *dev)
 	{
 		...
 
 		return 0;
 	}
 
-	static int dev_resume(struct pci_dev *dev)
+	static int dev_resume(struct device *dev)
 	{
 		...
 
@@ -165,8 +165,7 @@ Following piece of code illustrates the usage of the SR-IOV API.
 		.id_table =	dev_id_table,
 		.probe =	dev_probe,
 		.remove =	dev_remove,
-		.suspend =	dev_suspend,
-		.resume =	dev_resume,
+		.driver.pm =	&dev_pm_ops,
 		.shutdown =	dev_shutdown,
 		.sriov_configure = dev_sriov_configure,
 	};

Documentation/PCI/sysfs-pci.rst

@@ -125,7 +125,7 @@ implementation of that functionality. To support the historical interface of
 mmap() through files in /proc/bus/pci, platforms may also set HAVE_PCI_MMAP.
 
 Alternatively, platforms which set HAVE_PCI_MMAP may provide their own
-implementation of pci_mmap_page_range() instead of defining
+implementation of pci_mmap_resource_range() instead of defining
 ARCH_GENERIC_PCI_MMAP_RESOURCE.
 
 Platforms which support write-combining maps of PCI resources must define

Documentation/devicetree/bindings/pci/mediatek-pcie.txt

@@ -7,6 +7,7 @@ Required properties:
 	"mediatek,mt7622-pcie"
 	"mediatek,mt7623-pcie"
 	"mediatek,mt7629-pcie"
+	"airoha,en7523-pcie"
 - device_type: Must be "pci"
 - reg: Base addresses and lengths of the root ports.
 - reg-names: Names of the above areas to use during resource lookup.

Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.yaml

@@ -0,0 +1,319 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/nvidia,tegra194-pcie-ep.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra194 (and later) PCIe Endpoint controller (Synopsys DesignWare Core based)
+
+maintainers:
+  - Thierry Reding <[email protected]>
+  - Jon Hunter <[email protected]>
+  - Vidya Sagar <[email protected]>
+
+description: |
+  This PCIe controller is based on the Synopsys DesignWare PCIe IP and thus
+  inherits all the common properties defined in snps,dw-pcie-ep.yaml.  Some
+  of the controller instances are dual mode; they can work either in Root
+  Port mode or Endpoint mode but one at a time.
+
+  On Tegra194, controllers C0, C4 and C5 support Endpoint mode.
+  On Tegra234, controllers C5, C6, C7 and C10 support Endpoint mode.
+
+  Note: On Tegra194's P2972-0000 platform, only C5 controller can be enabled to
+  operate in the Endpoint mode because of the way the platform is designed.
+
+properties:
+  compatible:
+    enum:
+      - nvidia,tegra194-pcie-ep
+      - nvidia,tegra234-pcie-ep
+
+  reg:
+    items:
+      - description: controller's application logic registers
+      - description: iATU and DMA registers. This is where the iATU (internal
+          Address Translation Unit) registers of the PCIe core are made
+          available for software access.
+      - description: aperture where the Root Port's own configuration
+          registers are available.
+      - description: aperture used to map the remote Root Complex address space
+
+  reg-names:
+    items:
+      - const: appl
+      - const: atu_dma
+      - const: dbi
+      - const: addr_space
+
+  interrupts:
+    items:
+      - description: controller interrupt
+
+  interrupt-names:
+    items:
+      - const: intr
+
+  clocks:
+    items:
+      - description: module clock
+
+  clock-names:
+    items:
+      - const: core
+
+  resets:
+    items:
+      - description: APB bus interface reset
+      - description: module reset
+
+  reset-names:
+    items:
+      - const: apb
+      - const: core
+
+  reset-gpios:
+    description: Must contain a phandle to a GPIO controller followed by GPIO
+      that is being used as PERST input signal. Please refer to pci.txt.
+
+  phys:
+    minItems: 1
+    maxItems: 8
+
+  phy-names:
+    minItems: 1
+    items:
+      - const: p2u-0
+      - const: p2u-1
+      - const: p2u-2
+      - const: p2u-3
+      - const: p2u-4
+      - const: p2u-5
+      - const: p2u-6
+      - const: p2u-7
+
+  power-domains:
+    maxItems: 1
+    description: |
+      A phandle to the node that controls power to the respective PCIe
+      controller and a specifier name for the PCIe controller.
+
+      Tegra194 specifiers are defined in "include/dt-bindings/power/tegra194-powergate.h"
+      Tegra234 specifiers are defined in "include/dt-bindings/power/tegra234-powergate.h"
+
+  interconnects:
+    items:
+      - description: memory read client
+      - description: memory write client
+
+  interconnect-names:
+    items:
+      - const: dma-mem # read
+      - const: write
+
+  dma-coherent: true
+
+  nvidia,bpmp:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description: |
+      Must contain a pair of phandles to BPMP controller node followed by
+      controller ID. Following are the controller IDs for each controller:
+
+      Tegra194
+
+        0: C0
+        1: C1
+        2: C2
+        3: C3
+        4: C4
+        5: C5
+
+      Tegra234
+
+        0 : C0
+        1 : C1
+        2 : C2
+        3 : C3
+        4 : C4
+        5 : C5
+        6 : C6
+        7 : C7
+        8 : C8
+        9 : C9
+        10: C10
+
+    items:
+      - items:
+          - description: phandle to BPMP controller node
+          - description: PCIe controller ID
+            maximum: 10
+
+  nvidia,aspm-cmrt-us:
+    description: Common Mode Restore Time for proper operation of ASPM to be
+      specified in microseconds
+
+  nvidia,aspm-pwr-on-t-us:
+    description: Power On time for proper operation of ASPM to be specified in
+      microseconds
+
+  nvidia,aspm-l0s-entrance-latency-us:
+    description: ASPM L0s entrance latency to be specified in microseconds
+
+  vddio-pex-ctl-supply:
+    description: A phandle to the regulator supply for PCIe side band signals
+
+  nvidia,refclk-select-gpios:
+    maxItems: 1
+    description: GPIO used to enable REFCLK to controller from the host
+
+  nvidia,enable-ext-refclk:
+    description: |
+      This boolean property needs to be present if the controller is configured
+      to receive Reference Clock from the host.
+      NOTE: This is applicable only for Tegra234.
+
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  nvidia,enable-srns:
+    description: |
+      This boolean property needs to be present if the controller is
+      configured to operate in SRNS (Separate Reference Clocks with No
+      Spread-Spectrum Clocking).  NOTE: This is applicable only for
+      Tegra234.
+
+    $ref: /schemas/types.yaml#/definitions/flag
+
+allOf:
+  - $ref: /schemas/pci/snps,dw-pcie-ep.yaml#
+
+unevaluatedProperties: false
+
+required:
+  - interrupts
+  - interrupt-names
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+  - power-domains
+  - reset-gpios
+  - vddio-pex-ctl-supply
+  - num-lanes
+  - phys
+  - phy-names
+  - nvidia,bpmp
+
+examples:
+  - |
+    #include <dt-bindings/clock/tegra194-clock.h>
+    #include <dt-bindings/gpio/tegra194-gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/tegra194-powergate.h>
+    #include <dt-bindings/reset/tegra194-reset.h>
+
+    bus@0 {
+        #address-cells = <2>;
+        #size-cells = <2>;
+        ranges = <0x0 0x0 0x0 0x8 0x0>;
+
+        pcie-ep@141a0000 {
+            compatible = "nvidia,tegra194-pcie-ep";
+            reg = <0x00 0x141a0000 0x0 0x00020000>, /* appl registers (128K) */
+                  <0x00 0x3a040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+                  <0x00 0x3a080000 0x0 0x00040000>, /* DBI reg space (256K) */
+                  <0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */
+            reg-names = "appl", "atu_dma", "dbi", "addr_space";
+            interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
+            interrupt-names = "intr";
+
+            clocks = <&bpmp TEGRA194_CLK_PEX1_CORE_5>;
+            clock-names = "core";
+
+            resets = <&bpmp TEGRA194_RESET_PEX1_CORE_5_APB>,
+                     <&bpmp TEGRA194_RESET_PEX1_CORE_5>;
+            reset-names = "apb", "core";
+
+            power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8A>;
+            pinctrl-names = "default";
+            pinctrl-0 = <&clkreq_c5_bi_dir_state>;
+
+            nvidia,bpmp = <&bpmp 5>;
+
+            nvidia,aspm-cmrt-us = <60>;
+            nvidia,aspm-pwr-on-t-us = <20>;
+            nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+            vddio-pex-ctl-supply = <&vdd_1v8ao>;
+
+            reset-gpios = <&gpio TEGRA194_MAIN_GPIO(GG, 1) GPIO_ACTIVE_LOW>;
+
+            nvidia,refclk-select-gpios = <&gpio_aon TEGRA194_AON_GPIO(AA, 5)
+                                          GPIO_ACTIVE_HIGH>;
+
+            num-lanes = <8>;
+
+            phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>,
+                   <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>,
+                   <&p2u_nvhs_6>, <&p2u_nvhs_7>;
+
+            phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4",
+                        "p2u-5", "p2u-6", "p2u-7";
+        };
+    };
+
+  - |
+    #include <dt-bindings/clock/tegra234-clock.h>
+    #include <dt-bindings/gpio/tegra234-gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/tegra234-powergate.h>
+    #include <dt-bindings/reset/tegra234-reset.h>
+
+    bus@0 {
+        #address-cells = <2>;
+        #size-cells = <2>;
+        ranges = <0x0 0x0 0x0 0x8 0x0>;
+
+        pcie-ep@141a0000 {
+            compatible = "nvidia,tegra234-pcie-ep";
+            power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX8A>;
+            reg = <0x00 0x141a0000 0x0 0x00020000>, /* appl registers (128K)      */
+                  <0x00 0x3a040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+                  <0x00 0x3a080000 0x0 0x00040000>, /* DBI reg space (256K)       */
+                  <0x27 0x40000000 0x4 0x00000000>; /* Address Space (16G)        */
+            reg-names = "appl", "atu_dma", "dbi", "addr_space";
+
+            interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
+            interrupt-names = "intr";
+
+            clocks = <&bpmp TEGRA234_CLK_PEX1_C5_CORE>;
+            clock-names = "core";
+
+            resets = <&bpmp TEGRA234_RESET_PEX1_CORE_5_APB>,
+                     <&bpmp TEGRA234_RESET_PEX1_CORE_5>;
+            reset-names = "apb", "core";
+
+            nvidia,bpmp = <&bpmp 5>;
+
+            nvidia,enable-ext-refclk;
+            nvidia,aspm-cmrt-us = <60>;
+            nvidia,aspm-pwr-on-t-us = <20>;
+            nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+            vddio-pex-ctl-supply = <&p3701_vdd_1v8_ls>;
+
+            reset-gpios = <&gpio TEGRA234_MAIN_GPIO(AF, 1) GPIO_ACTIVE_LOW>;
+
+            nvidia,refclk-select-gpios = <&gpio_aon
+                                          TEGRA234_AON_GPIO(AA, 4)
+                                          GPIO_ACTIVE_HIGH>;
+
+            num-lanes = <8>;
+
+            phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>,
+                   <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>,
+                   <&p2u_nvhs_6>, <&p2u_nvhs_7>;
+
+            phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4",
+                        "p2u-5", "p2u-6", "p2u-7";
+        };
+    };