Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/gi…

…t/linville/wireless into for-davem

MAINTAINERS

@@ -1351,6 +1351,14 @@ W:	http://wireless.kernel.org/en/users/Drivers/ath9k
 S:	Supported
 F:	drivers/net/wireless/ath/ath9k/
 
+WILOCITY WIL6210 WIRELESS DRIVER
+M:	Vladimir Kondratiev <[email protected]>
+L:	[email protected]
+L:	[email protected]
+S:	Supported
+W:	http://wireless.kernel.org/en/users/Drivers/wil6210
+F:	drivers/net/wireless/ath/wil6210/
+
 CARL9170 LINUX COMMUNITY WIRELESS DRIVER
 M:	Christian Lamparter <[email protected]>
 L:	[email protected]

drivers/net/wireless/ath/Kconfig

@@ -30,5 +30,6 @@ source "drivers/net/wireless/ath/ath9k/Kconfig"
 source "drivers/net/wireless/ath/carl9170/Kconfig"
 source "drivers/net/wireless/ath/ath6kl/Kconfig"
 source "drivers/net/wireless/ath/ar5523/Kconfig"
+source "drivers/net/wireless/ath/wil6210/Kconfig"
 
 endif

drivers/net/wireless/ath/Makefile

@@ -3,6 +3,7 @@ obj-$(CONFIG_ATH9K_HW)		+= ath9k/
 obj-$(CONFIG_CARL9170)		+= carl9170/
 obj-$(CONFIG_ATH6KL)		+= ath6kl/
 obj-$(CONFIG_AR5523)		+= ar5523/
+obj-$(CONFIG_WIL6210)		+= wil6210/
 
 obj-$(CONFIG_ATH_COMMON)	+= ath.o
 

drivers/net/wireless/ath/wil6210/Kconfig

@@ -0,0 +1,29 @@
+config WIL6210
+	tristate "Wilocity 60g WiFi card wil6210 support"
+	depends on CFG80211
+	depends on PCI
+	default n
+	---help---
+	  This module adds support for wireless adapter based on
+	  wil6210 chip by Wilocity. It supports operation on the
+	  60 GHz band, covered by the IEEE802.11ad standard.
+
+	  http://wireless.kernel.org/en/users/Drivers/wil6210
+
+	  If you choose to build it as a module, it will be called
+	  wil6210
+
+config WIL6210_ISR_COR
+	bool "Use Clear-On-Read mode for ISR registers for wil6210"
+	depends on WIL6210
+	default y
+	---help---
+	  ISR registers on wil6210 chip may operate in either
+	  COR (Clear-On-Read) or W1C (Write-1-to-Clear) mode.
+	  For production code, use COR (say y); is default since
+	  it saves extra target transaction;
+	  For ISR debug, use W1C (say n); is allows to monitor ISR
+	  registers with debugfs. If COR were used, ISR would
+	  self-clear when accessed for debug purposes, it makes
+	  such monitoring impossible.
+	  Say y unless you debug interrupts

drivers/net/wireless/ath/wil6210/Makefile

@@ -0,0 +1,13 @@
+obj-$(CONFIG_WIL6210) += wil6210.o
+
+wil6210-objs := main.o
+wil6210-objs += netdev.o
+wil6210-objs += cfg80211.o
+wil6210-objs += pcie_bus.o
+wil6210-objs += debugfs.o
+wil6210-objs += wmi.o
+wil6210-objs += interrupt.o
+wil6210-objs += txrx.o
+
+subdir-ccflags-y += -Werror
+subdir-ccflags-y += -D__CHECK_ENDIAN__