Merge tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/k…

…ernel/git/gregkh/char-misc

Pull char/misc driver updates from Greg KH:
 "Here's the big char/misc driver patchset for 4.1-rc1.

  Lots of different driver subsystem updates here, nothing major, full
  details are in the shortlog.

  All of this has been in linux-next for a while"

* tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (133 commits)
  mei: trace: remove unused TRACE_SYSTEM_STRING
  DTS: ARM: OMAP3-N900: Add lis3lv02d support
  Documentation: DT: lis302: update wakeup binding
  lis3lv02d: DT: add wakeup unit 2 and wakeup threshold
  lis3lv02d: DT: use s32 to support negative values
  Drivers: hv: hv_balloon: correctly handle num_pages>INT_MAX case
  Drivers: hv: hv_balloon: correctly handle val.freeram<num_pages case
  mei: replace check for connection instead of transitioning
  mei: use mei_cl_is_connected consistently
  mei: fix mei_poll operation
  hv_vmbus: Add gradually increased delay for retries in vmbus_post_msg()
  Drivers: hv: hv_balloon: survive ballooning request with num_pages=0
  Drivers: hv: hv_balloon: eliminate jumps in piecewiese linear floor function
  Drivers: hv: hv_balloon: do not online pages in offline blocks
  hv: remove the per-channel workqueue
  hv: don't schedule new works in vmbus_onoffer()/vmbus_onoffer_rescind()
  hv: run non-blocking message handlers in the dispatch tasklet
  coresight: moving to new "hwtracing" directory
  coresight-tmc: Adding a status interface to sysfs
  coresight: remove the unnecessary configuration coresight-default-sink
  ...

Documentation/devicetree/bindings/arm/coresight.txt

@@ -61,7 +61,6 @@ Example:
 		compatible = "arm,coresight-etb10", "arm,primecell";
 		reg = <0 0x20010000 0 0x1000>;
 
-		coresight-default-sink;
 		clocks = <&oscclk6a>;
 		clock-names = "apb_pclk";
 		port {

Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt

@@ -0,0 +1,18 @@
+USB GPIO Extcon device
+
+This is a virtual device used to generate USB cable states from the USB ID pin
+connected to a GPIO pin.
+
+Required properties:
+- compatible: Should be "linux,extcon-usb-gpio"
+- id-gpio: gpio for USB ID pin. See gpio binding.
+
+Example: Examples of extcon-usb-gpio node in dra7-evm.dts as listed below:
+	extcon_usb1 {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>;
+	}
+
+	&omap_dwc3_1 {
+		extcon = <&extcon_usb1>;
+	};

Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt

@@ -0,0 +1,75 @@
+* Ingenic JZ4780 NAND/external memory controller (NEMC)
+
+This file documents the device tree bindings for the NEMC external memory
+controller in Ingenic JZ4780
+
+Required properties:
+- compatible: Should be set to one of:
+    "ingenic,jz4780-nemc" (JZ4780)
+- reg: Should specify the NEMC controller registers location and length.
+- clocks: Clock for the NEMC controller.
+- #address-cells: Must be set to 2.
+- #size-cells: Must be set to 1.
+- ranges: A set of ranges for each bank describing the physical memory layout.
+  Each should specify the following 4 integer values:
+
+    <cs number> 0 <physical address of mapping> <size of mapping>
+
+Each child of the NEMC node describes a device connected to the NEMC.
+
+Required child node properties:
+- reg: Should contain at least one register specifier, given in the following
+  format:
+
+    <cs number> <offset> <size>
+
+  Multiple registers can be specified across multiple banks. This is needed,
+  for example, for packaged NAND devices with multiple dies. Such devices
+  should be grouped into a single node.
+
+Optional child node properties:
+- ingenic,nemc-bus-width: Specifies the bus width in bits. Defaults to 8 bits.
+- ingenic,nemc-tAS: Address setup time in nanoseconds.
+- ingenic,nemc-tAH: Address hold time in nanoseconds.
+- ingenic,nemc-tBP: Burst pitch time in nanoseconds.
+- ingenic,nemc-tAW: Access wait time in nanoseconds.
+- ingenic,nemc-tSTRV: Static memory recovery time in nanoseconds.
+
+If a child node references multiple banks in its "reg" property, the same value
+for all optional parameters will be configured for all banks. If any optional
+parameters are omitted, they will be left unchanged from whatever they are
+configured to when the NEMC device is probed (which may be the reset value as
+given in the hardware reference manual, or a value configured by the boot
+loader).
+
+Example (NEMC node with a NAND child device attached at CS1):
+
+nemc: nemc@13410000 {
+	compatible = "ingenic,jz4780-nemc";
+	reg = <0x13410000 0x10000>;
+
+	#address-cells = <2>;
+	#size-cells = <1>;
+
+	ranges = <1 0 0x1b000000 0x1000000
+		  2 0 0x1a000000 0x1000000
+		  3 0 0x19000000 0x1000000
+		  4 0 0x18000000 0x1000000
+		  5 0 0x17000000 0x1000000
+		  6 0 0x16000000 0x1000000>;
+
+	clocks = <&cgu JZ4780_CLK_NEMC>;
+
+	nand: nand@1 {
+		compatible = "ingenic,jz4780-nand";
+		reg = <1 0 0x1000000>;
+
+		ingenic,nemc-tAS = <10>;
+		ingenic,nemc-tAH = <5>;
+		ingenic,nemc-tBP = <10>;
+		ingenic,nemc-tAW = <15>;
+		ingenic,nemc-tSTRV = <100>;
+
+		...
+	};
+};

Documentation/devicetree/bindings/misc/lis302.txt

@@ -46,11 +46,18 @@ Optional properties for all bus drivers:
 				interrupt 2
  - st,wakeup-{x,y,z}-{lo,hi}:	set wakeup condition on x/y/z axis for
 				upper/lower limit
+ - st,wakeup-threshold:		set wakeup threshold
+ - st,wakeup2-{x,y,z}-{lo,hi}:	set wakeup condition on x/y/z axis for
+				upper/lower limit for second wakeup
+				engine.
+ - st,wakeup2-threshold:	set wakeup threshold for second wakeup
+				engine.
  - st,highpass-cutoff-hz=:	1, 2, 4 or 8 for 1Hz, 2Hz, 4Hz or 8Hz of
 				highpass cut-off frequency
  - st,hipass{1,2}-disable:	disable highpass 1/2.
  - st,default-rate=:		set the default rate
- - st,axis-{x,y,z}=:		set the axis to map to the three coordinates
+ - st,axis-{x,y,z}=:		set the axis to map to the three coordinates.
+				Negative values can be used for inverted axis.
  - st,{min,max}-limit-{x,y,z}	set the min/max limits for x/y/z axis
 				(used by self-test)
 

Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt

@@ -1,6 +1,6 @@
 Qualcomm SPMI Controller (PMIC Arbiter)
 
-The SPMI PMIC Arbiter is found on the Snapdragon 800 Series.  It is an SPMI
+The SPMI PMIC Arbiter is found on Snapdragon chipsets.  It is an SPMI
 controller with wrapping arbitration logic to allow for multiple on-chip
 devices to control a single SPMI master.
 
@@ -19,6 +19,10 @@ Required properties:
      "core" - core registers
      "intr" - interrupt controller registers
      "cnfg" - configuration registers
+   Registers used only for V2 PMIC Arbiter:
+     "chnls"  - tx-channel per virtual slave registers.
+     "obsrvr" - rx-channel (called observer) per virtual slave registers.
+
 - reg : address + size pairs describing the PMIC arb register sets; order must
         correspond with the order of entries in reg-names
 - #address-cells : must be set to 2

Documentation/driver-model/devres.txt

@@ -276,6 +276,7 @@ IOMAP
   devm_ioport_unmap()
   devm_ioremap()
   devm_ioremap_nocache()
+  devm_ioremap_wc()
   devm_ioremap_resource() : checks resource, requests memory region, ioremaps
   devm_iounmap()
   pcim_iomap()

Documentation/trace/coresight.txt

@@ -14,7 +14,7 @@ document is concerned with the latter.
 HW assisted tracing is becoming increasingly useful when dealing with systems
 that have many SoCs and other components like GPU and DMA engines.  ARM has
 developed a HW assisted tracing solution by means of different components, each
-being added to a design at systhesis time to cater to specific tracing needs.
+being added to a design at synthesis time to cater to specific tracing needs.
 Compoments are generally categorised as source, link and sinks and are
 (usually) discovered using the AMBA bus.
 

MAINTAINERS

@@ -958,7 +958,7 @@ ARM/CORESIGHT FRAMEWORK AND DRIVERS
 M:	Mathieu Poirier <[email protected]>
 L:	[email protected] (moderated for non-subscribers)
 S:	Maintained
-F:	drivers/coresight/*
+F:	drivers/hwtracing/coresight/*
 F:	Documentation/trace/coresight.txt
 F:	Documentation/devicetree/bindings/arm/coresight.txt
 F:	Documentation/ABI/testing/sysfs-bus-coresight-devices-*
@@ -1828,7 +1828,7 @@ S:	Supported
 F:	drivers/spi/spi-atmel.*
 
 ATMEL SSC DRIVER
-M:	Bo Shen <voice.shen@atmel.com>
+M:	Nicolas Ferre <nicolas.ferre@atmel.com>
 L:	[email protected] (moderated for non-subscribers)
 S:	Supported
 F:	drivers/misc/atmel-ssc.c

arch/arm/Kconfig.debug

@@ -1610,59 +1610,6 @@ config DEBUG_SET_MODULE_RONX
 	  against certain classes of kernel exploits.
 	  If in doubt, say "N".
 
-menuconfig CORESIGHT
-	bool "CoreSight Tracing Support"
-	select ARM_AMBA
-	help
-	  This framework provides a kernel interface for the CoreSight debug
-	  and trace drivers to register themselves with. It's intended to build
-	  a topological view of the CoreSight components based on a DT
-	  specification and configure the right serie of components when a
-	  trace source gets enabled.
-
-if CORESIGHT
-config CORESIGHT_LINKS_AND_SINKS
-	bool "CoreSight Link and Sink drivers"
-	help
-	  This enables support for CoreSight link and sink drivers that are
-	  responsible for transporting and collecting the trace data
-	  respectively.  Link and sinks are dynamically aggregated with a trace
-	  entity at run time to form a complete trace path.
-
-config CORESIGHT_LINK_AND_SINK_TMC
-	bool "Coresight generic TMC driver"
-	depends on CORESIGHT_LINKS_AND_SINKS
-	help
-	  This enables support for the Trace Memory Controller driver.  Depending
-	  on its configuration the device can act as a link (embedded trace router
-	  - ETR) or sink (embedded trace FIFO).  The driver complies with the
-	  generic implementation of the component without special enhancement or
-	  added features.
-
-config CORESIGHT_SINK_TPIU
-	bool "Coresight generic TPIU driver"
-	depends on CORESIGHT_LINKS_AND_SINKS
-	help
-	  This enables support for the Trace Port Interface Unit driver, responsible
-	  for bridging the gap between the on-chip coresight components and a trace
-	  port collection engine, typically connected to an external host for use
-	  case capturing more traces than the on-board coresight memory can handle.
-
-config CORESIGHT_SINK_ETBV10
-	bool "Coresight ETBv1.0 driver"
-	depends on CORESIGHT_LINKS_AND_SINKS
-	help
-	  This enables support for the Embedded Trace Buffer version 1.0 driver
-	  that complies with the generic implementation of the component without
-	  special enhancement or added features.
+source "drivers/hwtracing/coresight/Kconfig"
 
-config CORESIGHT_SOURCE_ETM3X
-	bool "CoreSight Embedded Trace Macrocell 3.x driver"
-	select CORESIGHT_LINKS_AND_SINKS
-	help
-	  This driver provides support for processor ETM3.x and PTM1.x modules,
-	  which allows tracing the instructions that a processor is executing
-	  This is primarily useful for instruction level tracing.  Depending
-	  the ETM version data tracing may also be available.
-endif
 endmenu

arch/arm/boot/dts/hip04.dtsi

@@ -275,7 +275,6 @@
 		compatible = "arm,coresight-etb10", "arm,primecell";
 		reg = <0 0xe3c42000 0 0x1000>;
 
-		coresight-default-sink;
 		clocks = <&clk_375m>;
 		clock-names = "apb_pclk";
 		port {

arch/arm/boot/dts/omap3-beagle-xm.dts

@@ -150,7 +150,6 @@
 		compatible = "arm,coresight-etb10", "arm,primecell";
 		reg = <0x5401b000 0x1000>;
 
-		coresight-default-sink;
 		clocks = <&emu_src_ck>;
 		clock-names = "apb_pclk";
 		port {

arch/arm/boot/dts/omap3-beagle.dts

@@ -145,7 +145,6 @@
 		compatible = "arm,coresight-etb10", "arm,primecell";
 		reg = <0x5401b000 0x1000>;
 
-		coresight-default-sink;
 		clocks = <&emu_src_ck>;
 		clock-names = "apb_pclk";
 		port {

arch/arm/boot/dts/omap3-n900.dts

@@ -609,6 +609,58 @@
 	pinctrl-0 = <&i2c3_pins>;
 
 	clock-frequency = <400000>;
+
+	lis302dl: lis3lv02d@1d {
+		compatible = "st,lis3lv02d";
+		reg = <0x1d>;
+
+		Vdd-supply = <&vaux1>;
+		Vdd_IO-supply = <&vio>;
+
+		interrupt-parent = <&gpio6>;
+		interrupts = <21 20>; /* 181 and 180 */
+
+		/* click flags */
+		st,click-single-x;
+		st,click-single-y;
+		st,click-single-z;
+
+		/* Limits are 0.5g * value */
+		st,click-threshold-x = <8>;
+		st,click-threshold-y = <8>;
+		st,click-threshold-z = <10>;
+
+		/* Click must be longer than time limit */
+		st,click-time-limit = <9>;
+
+		/* Kind of debounce filter */
+		st,click-latency = <50>;
+
+		/* Interrupt line 2 for click detection */
+		st,irq2-click;
+
+		st,wakeup-x-hi;
+		st,wakeup-y-hi;
+		st,wakeup-threshold = <(800/18)>; /* millig-value / 18 to get HW values */
+
+		st,wakeup2-z-hi;
+		st,wakeup2-threshold = <(900/18)>; /* millig-value / 18 to get HW values */
+
+		st,hipass1-disable;
+		st,hipass2-disable;
+
+		st,axis-x = <1>;    /* LIS3_DEV_X */
+		st,axis-y = <(-2)>; /* LIS3_INV_DEV_Y */
+		st,axis-z = <(-3)>; /* LIS3_INV_DEV_Z */
+
+		st,min-limit-x = <(-32)>;
+		st,min-limit-y = <3>;
+		st,min-limit-z = <3>;
+
+		st,max-limit-x = <(-3)>;
+		st,max-limit-y = <32>;
+		st,max-limit-z = <32>;
+	};
 };
 
 &mmc1 {

arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts

@@ -362,7 +362,6 @@
 		compatible = "arm,coresight-etb10", "arm,primecell";
 		reg = <0 0x20010000 0 0x1000>;
 
-		coresight-default-sink;
 		clocks = <&oscclk6a>;
 		clock-names = "apb_pclk";
 		port {

arch/arm64/Kconfig.debug

@@ -89,4 +89,6 @@ config DEBUG_ALIGN_RODATA
 
 	  If in doubt, say N
 
+source "drivers/hwtracing/coresight/Kconfig"
+
 endmenu

arch/m32r/include/asm/io.h

@@ -67,6 +67,7 @@ static inline void __iomem *ioremap(unsigned long offset, unsigned long size)
 
 extern void iounmap(volatile void __iomem *addr);
 #define ioremap_nocache(off,size) ioremap(off,size)
+#define ioremap_wc ioremap_nocache
 
 /*
  * IO bus memory addresses are also 1:1 with the physical address

arch/x86/include/uapi/asm/hyperv.h

@@ -225,6 +225,8 @@
 #define HV_STATUS_INVALID_HYPERCALL_CODE	2
 #define HV_STATUS_INVALID_HYPERCALL_INPUT	3
 #define HV_STATUS_INVALID_ALIGNMENT		4
+#define HV_STATUS_INSUFFICIENT_MEMORY		11
+#define HV_STATUS_INVALID_CONNECTION_ID		18
 #define HV_STATUS_INSUFFICIENT_BUFFERS		19
 
 typedef struct _HV_REFERENCE_TSC_PAGE {

drivers/Makefile

@@ -163,5 +163,5 @@ obj-$(CONFIG_POWERCAP)		+= powercap/
 obj-$(CONFIG_MCB)		+= mcb/
 obj-$(CONFIG_RAS)		+= ras/
 obj-$(CONFIG_THUNDERBOLT)	+= thunderbolt/
-obj-$(CONFIG_CORESIGHT)		+= coresight/
+obj-$(CONFIG_CORESIGHT)		+= hwtracing/coresight/
 obj-$(CONFIG_ANDROID)		+= android/