diff --git a/Documentation/arm/00-INDEX b/Documentation/arm/00-INDEX index 7f5fc3ba9c912d..ecf7d04bca2601 100644 --- a/Documentation/arm/00-INDEX +++ b/Documentation/arm/00-INDEX @@ -6,6 +6,8 @@ Interrupts - ARM Interrupt subsystem documentation IXP2000 - Release Notes for Linux on Intel's IXP2000 Network Processor +msm + - MSM specific documentation Netwinder - Netwinder specific documentation Porting diff --git a/Documentation/arm/msm/gpiomux.txt b/Documentation/arm/msm/gpiomux.txt new file mode 100644 index 00000000000000..67a81620adf67d --- /dev/null +++ b/Documentation/arm/msm/gpiomux.txt @@ -0,0 +1,176 @@ +This document provides an overview of the msm_gpiomux interface, which +is used to provide gpio pin multiplexing and configuration on mach-msm +targets. + +History +======= + +The first-generation API for gpio configuration & multiplexing on msm +is the function gpio_tlmm_config(). This function has a few notable +shortcomings, which led to its deprecation and replacement by gpiomux: + +The 'disable' parameter: Setting the second parameter to +gpio_tlmm_config to GPIO_CFG_DISABLE tells the peripheral +processor in charge of the subsystem to perform a look-up into a +low-power table and apply the low-power/sleep setting for the pin. +As the msm family evolved this became problematic. Not all pins +have sleep settings, not all peripheral processors will accept requests +to apply said sleep settings, and not all msm targets have their gpio +subsystems managed by a peripheral processor. In order to get consistent +behavior on all targets, drivers are forced to ignore this parameter, +rendering it useless. + +The 'direction' flag: for all mux-settings other than raw-gpio (0), +the output-enable bit of a gpio is hard-wired to a known +input (usually VDD or ground). For those settings, the direction flag +is meaningless at best, and deceptive at worst. In addition, using the +direction flag to change output-enable (OE) directly can cause trouble in +gpiolib, which has no visibility into gpio direction changes made +in this way. Direction control in gpio mode should be made through gpiolib. + +Key Features of gpiomux +======================= + +- A consistent interface across all generations of msm. Drivers can expect +the same results on every target. +- gpiomux plays nicely with gpiolib. Functions that should belong to gpiolib +are left to gpiolib and not duplicated here. gpiomux is written with the +intent that gpio_chips will call gpiomux reference-counting methods +from their request() and free() hooks, providing full integration. +- Tabular configuration. Instead of having to call gpio_tlmm_config +hundreds of times, gpio configuration is placed in a single table. +- Per-gpio sleep. Each gpio is individually reference counted, allowing only +those lines which are in use to be put in high-power states. +- 0 means 'do nothing': all flags are designed so that the default memset-zero +equates to a sensible default of 'no configuration', preventing users +from having to provide hundreds of 'no-op' configs for unused or +unwanted lines. + +Usage +===== + +To use gpiomux, provide configuration information for relevant gpio lines +in the msm_gpiomux_configs table. Since a 0 equates to "unconfigured", +only those lines to be managed by gpiomux need to be specified. Here +is a completely fictional example: + +struct msm_gpiomux_config msm_gpiomux_configs[GPIOMUX_NGPIOS] = { + [12] = { + .active = GPIOMUX_VALID | GPIOMUX_DRV_8MA | GPIOMUX_FUNC_1, + .suspended = GPIOMUX_VALID | GPIOMUX_PULL_DOWN, + }, + [34] = { + .suspended = GPIOMUX_VALID | GPIOMUX_PULL_DOWN, + }, +}; + +To indicate that a gpio is in use, call msm_gpiomux_get() to increase +its reference count. To decrease the reference count, call msm_gpiomux_put(). + +The effect of this configuration is as follows: + +When the system boots, gpios 12 and 34 will be initialized with their +'suspended' configurations. All other gpios, which were left unconfigured, +will not be touched. + +When msm_gpiomux_get() is called on gpio 12 to raise its reference count +above 0, its active configuration will be applied. Since no other gpio +line has a valid active configuration, msm_gpiomux_get() will have no +effect on any other line. + +When msm_gpiomux_put() is called on gpio 12 or 34 to drop their reference +count to 0, their suspended configurations will be applied. +Since no other gpio line has a valid suspended configuration, no other +gpio line will be effected by msm_gpiomux_put(). Since gpio 34 has no valid +active configuration, this is effectively a no-op for gpio 34 as well, +with one small caveat, see the section "About Output-Enable Settings". + +All of the GPIOMUX_VALID flags may seem like unnecessary overhead, but +they address some important issues. As unused entries (all those +except 12 and 34) are zero-filled, gpiomux needs a way to distinguish +the used fields from the unused. In addition, the all-zero pattern +is a valid configuration! Therefore, gpiomux defines an additional bit +which is used to indicate when a field is used. This has the pleasant +side-effect of allowing calls to msm_gpiomux_write to use '0' to indicate +that a value should not be changed: + + msm_gpiomux_write(0, GPIOMUX_VALID, 0); + +replaces the active configuration of gpio 0 with an all-zero configuration, +but leaves the suspended configuration as it was. + +Static Configurations +===================== + +To install a static configuration, which is applied at boot and does +not change after that, install a configuration with a suspended component +but no active component, as in the previous example: + + [34] = { + .suspended = GPIOMUX_VALID | GPIOMUX_PULL_DOWN, + }, + +The suspended setting is applied during boot, and the lack of any valid +active setting prevents any other setting from being applied at runtime. +If other subsystems attempting to access the line is a concern, one could +*really* anchor the configuration down by calling msm_gpiomux_get on the +line at initialization to move the line into active mode. With the line +held, it will never be re-suspended, and with no valid active configuration, +no new configurations will be applied. + +But then, if having other subsystems grabbing for the line is truly a concern, +it should be reserved with gpio_request instead, which carries an implicit +msm_gpiomux_get. + +gpiomux and gpiolib +=================== + +It is expected that msm gpio_chips will call msm_gpiomux_get() and +msm_gpiomux_put() from their request and free hooks, like this fictional +example: + +static int request(struct gpio_chip *chip, unsigned offset) +{ + return msm_gpiomux_get(chip->base + offset); +} + +static void free(struct gpio_chip *chip, unsigned offset) +{ + msm_gpiomux_put(chip->base + offset); +} + + ...somewhere in a gpio_chip declaration... + .request = request, + .free = free, + +This provides important functionality: +- It guarantees that a gpio line will have its 'active' config applied + when the line is requested, and will not be suspended while the line + remains requested; and +- It guarantees that gpio-direction settings from gpiolib behave sensibly. + See "About Output-Enable Settings." + +This mechanism allows for "auto-request" of gpiomux lines via gpiolib +when it is suitable. Drivers wishing more exact control are, of course, +free to also use msm_gpiomux_set and msm_gpiomux_get. + +About Output-Enable Settings +============================ + +Some msm targets do not have the ability to query the current gpio +configuration setting. This means that changes made to the output-enable +(OE) bit by gpiolib cannot be consistently detected and preserved by gpiomux. +Therefore, when gpiomux applies a configuration setting, any direction +settings which may have been applied by gpiolib are lost and the default +input settings are re-applied. + +For this reason, drivers should not assume that gpio direction settings +continue to hold if they free and then re-request a gpio. This seems like +common sense - after all, anybody could have obtained the line in the +meantime - but it needs saying. + +This also means that calls to msm_gpiomux_write will reset the OE bit, +which means that if the gpio line is held by a client of gpiolib and +msm_gpiomux_write is called, the direction setting has been lost and +gpiolib's internal state has been broken. +Release gpio lines before reconfiguring them. diff --git a/MAINTAINERS b/MAINTAINERS index 6f5b5b2b528d93..b618b1e86c46b6 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -990,11 +990,23 @@ S: Supported F: arch/arm/mach-shmobile/ F: drivers/sh/ +ARM/TELECHIPS ARM ARCHITECTURE +M: "Hans J. Koch" +L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) +S: Maintained +F: arch/arm/plat-tcc/ +F: arch/arm/mach-tcc8k/ + ARM/TECHNOLOGIC SYSTEMS TS7250 MACHINE SUPPORT M: Lennert Buytenhek L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) S: Maintained +ARM/TETON BGA MACHINE SUPPORT +M: Mark F. Brown +L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) +S: Maintained + ARM/THECUS N2100 MACHINE SUPPORT M: Lennert Buytenhek L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) diff --git a/Makefile b/Makefile index d3c10719bbbd5b..3e438055a92c50 100644 --- a/Makefile +++ b/Makefile @@ -554,8 +554,15 @@ endif ifdef CONFIG_FRAME_POINTER KBUILD_CFLAGS += -fno-omit-frame-pointer -fno-optimize-sibling-calls else +# Some targets (ARM with Thumb2, for example), can't be built with frame +# pointers. For those, we don't have FUNCTION_TRACER automatically +# select FRAME_POINTER. However, FUNCTION_TRACER adds -pg, and this is +# incompatible with -fomit-frame-pointer with current GCC, so we don't use +# -fomit-frame-pointer with FUNCTION_TRACER. +ifndef CONFIG_FUNCTION_TRACER KBUILD_CFLAGS += -fomit-frame-pointer endif +endif ifdef CONFIG_DEBUG_INFO KBUILD_CFLAGS += -g diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 9103904b3daba6..3849887157e720 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -19,6 +19,8 @@ config ARM select HAVE_KPROBES if (!XIP_KERNEL) select HAVE_KRETPROBES if (HAVE_KPROBES) select HAVE_FUNCTION_TRACER if (!XIP_KERNEL) + select HAVE_FTRACE_MCOUNT_RECORD if (!XIP_KERNEL) + select HAVE_DYNAMIC_FTRACE if (!XIP_KERNEL) select HAVE_GENERIC_DMA_COHERENT select HAVE_KERNEL_GZIP select HAVE_KERNEL_LZO @@ -27,6 +29,7 @@ config ARM select HAVE_PERF_EVENTS select PERF_USE_VMALLOC select HAVE_REGS_AND_STACK_ACCESS_API + select HAVE_HW_BREAKPOINT if (PERF_EVENTS && (CPU_V6 || CPU_V7)) help The ARM series is a line of low-power-consumption RISC chip designs licensed by ARM Ltd and targeted at embedded applications and @@ -146,6 +149,9 @@ config ARCH_HAS_CPUFREQ and that the relevant menu configurations are displayed for it. +config ARCH_HAS_CPU_IDLE_WAIT + def_bool y + config GENERIC_HWEIGHT bool default y @@ -511,6 +517,7 @@ config ARCH_MMP select GENERIC_CLOCKEVENTS select TICK_ONESHOT select PLAT_PXA + select SPARSE_IRQ help Support for Marvell's PXA168/PXA910(MMP) and MMP2 processor line. @@ -588,6 +595,7 @@ config ARCH_PXA select GENERIC_CLOCKEVENTS select TICK_ONESHOT select PLAT_PXA + select SPARSE_IRQ help Support for Intel/Marvell's PXA2xx/PXA3xx processor line. @@ -679,8 +687,8 @@ config ARCH_S3C64XX help Samsung S3C64XX series based systems -config ARCH_S5P6440 - bool "Samsung S5P6440" +config ARCH_S5P64X0 + bool "Samsung S5P6440 S5P6450" select CPU_V6 select GENERIC_GPIO select HAVE_CLK @@ -689,7 +697,8 @@ config ARCH_S5P6440 select HAVE_S3C2410_I2C select HAVE_S3C_RTC help - Samsung S5P6440 CPU based systems + Samsung S5P64X0 CPU based systems, such as the Samsung SMDK6440, + SMDK6450. config ARCH_S5P6442 bool "Samsung S5P6442" @@ -748,6 +757,15 @@ config ARCH_SHARK Support for the StrongARM based Digital DNARD machine, also known as "Shark" (). +config ARCH_TCC_926 + bool "Telechips TCC ARM926-based systems" + select CPU_ARM926T + select HAVE_CLK + select COMMON_CLKDEV + select GENERIC_CLOCKEVENTS + help + Support for Telechips TCC ARM926-based systems. + config ARCH_LH7A40X bool "Sharp LH7A40X" select CPU_ARM922T @@ -916,6 +934,8 @@ source "arch/arm/plat-s5p/Kconfig" source "arch/arm/plat-spear/Kconfig" +source "arch/arm/plat-tcc/Kconfig" + if ARCH_S3C2410 source "arch/arm/mach-s3c2400/Kconfig" source "arch/arm/mach-s3c2410/Kconfig" @@ -929,7 +949,7 @@ if ARCH_S3C64XX source "arch/arm/mach-s3c64xx/Kconfig" endif -source "arch/arm/mach-s5p6440/Kconfig" +source "arch/arm/mach-s5p64x0/Kconfig" source "arch/arm/mach-s5p6442/Kconfig" @@ -1003,7 +1023,7 @@ endif config ARM_ERRATA_411920 bool "ARM errata: Invalidation of the Instruction Cache operation can fail" - depends on CPU_V6 && !SMP + depends on CPU_V6 help Invalidation of the Instruction Cache operation can fail. This erratum is present in 1136 (before r1p4), 1156 and 1176. @@ -1182,13 +1202,13 @@ source "kernel/time/Kconfig" config SMP bool "Symmetric Multi-Processing (EXPERIMENTAL)" - depends on EXPERIMENTAL && (REALVIEW_EB_ARM11MP || REALVIEW_EB_A9MP ||\ - MACH_REALVIEW_PB11MP || MACH_REALVIEW_PBX || ARCH_OMAP4 ||\ - ARCH_S5PV310 || ARCH_TEGRA || ARCH_U8500 || ARCH_VEXPRESS_CA9X4) + depends on EXPERIMENTAL depends on GENERIC_CLOCKEVENTS + depends on REALVIEW_EB_ARM11MP || REALVIEW_EB_A9MP || \ + MACH_REALVIEW_PB11MP || MACH_REALVIEW_PBX || ARCH_OMAP4 ||\ + ARCH_S5PV310 || ARCH_TEGRA || ARCH_U8500 || ARCH_VEXPRESS_CA9X4 select USE_GENERIC_SMP_HELPERS - select HAVE_ARM_SCU if ARCH_REALVIEW || ARCH_OMAP4 || ARCH_S5PV310 ||\ - ARCH_TEGRA || ARCH_U8500 || ARCH_VEXPRESS_CA9X4 + select HAVE_ARM_SCU help This enables support for systems with more than one CPU. If you have a system with only one CPU, like most personal computers, say N. If @@ -1206,6 +1226,19 @@ config SMP If you don't know what to do here, say N. +config SMP_ON_UP + bool "Allow booting SMP kernel on uniprocessor systems (EXPERIMENTAL)" + depends on EXPERIMENTAL + depends on SMP && !XIP && !THUMB2_KERNEL + default y + help + SMP kernels contain instructions which fail on non-SMP processors. + Enabling this option allows the kernel to modify itself to make + these instructions safe. Disabling it allows about 1K of space + savings. + + If you don't know what to do here, say Y. + config HAVE_ARM_SCU bool depends on SMP @@ -1256,12 +1289,9 @@ config HOTPLUG_CPU config LOCAL_TIMERS bool "Use local timer interrupts" - depends on SMP && (REALVIEW_EB_ARM11MP || MACH_REALVIEW_PB11MP || \ - REALVIEW_EB_A9MP || MACH_REALVIEW_PBX || ARCH_OMAP4 || \ - ARCH_S5PV310 || ARCH_TEGRA || ARCH_U8500 || ARCH_VEXPRESS_CA9X4) + depends on SMP default y - select HAVE_ARM_TWD if ARCH_REALVIEW || ARCH_OMAP4 || ARCH_S5PV310 || \ - ARCH_TEGRA || ARCH_U8500 || ARCH_VEXPRESS + select HAVE_ARM_TWD help Enable support for local timers on SMP platforms, rather then the legacy IPI broadcast method. Local timers allows the system @@ -1272,7 +1302,7 @@ source kernel/Kconfig.preempt config HZ int - default 200 if ARCH_EBSA110 || ARCH_S3C2410 || ARCH_S5P6440 || \ + default 200 if ARCH_EBSA110 || ARCH_S3C2410 || ARCH_S5P64X0 || \ ARCH_S5P6442 || ARCH_S5PV210 || ARCH_S5PV310 default OMAP_32K_TIMER_HZ if ARCH_OMAP && OMAP_32K_TIMER default AT91_TIMER_HZ if ARCH_AT91 @@ -1478,6 +1508,20 @@ config UACCESS_WITH_MEMCPY However, if the CPU data cache is using a write-allocate mode, this option is unlikely to provide any performance gain. +config SECCOMP + bool + prompt "Enable seccomp to safely compute untrusted bytecode" + ---help--- + This kernel feature is useful for number crunching applications + that may need to compute untrusted bytecode during their + execution. By using pipes or other transports made available to + the process as file descriptors supporting the read/write + syscalls, it's possible to isolate those applications in + their own address space using seccomp. Once seccomp is + enabled via prctl(PR_SET_SECCOMP), it cannot be disabled + and the task is only allowed to execute a few safe syscalls + defined by each seccomp mode. + config CC_STACKPROTECTOR bool "Enable -fstack-protector buffer overflow detection (EXPERIMENTAL)" help diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index 91344af75f3969..2fd0b99afc4bc8 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug @@ -2,6 +2,20 @@ menu "Kernel hacking" source "lib/Kconfig.debug" +config STRICT_DEVMEM + bool "Filter access to /dev/mem" + depends on MMU + ---help--- + If this option is disabled, you allow userspace (root) access to all + of memory, including kernel and userspace memory. Accidental + access to this is obviously disastrous, but specific access can + be used by people debugging the kernel. + + If this option is switched on, the /dev/mem file only allows + userspace access to memory mapped peripherals. + + If in doubt, say Y. + # RMK wants arm kernels compiled with frame pointers or stack unwinding. # If you know what you are doing and are willing to live without stack # traces, you can get a slightly smaller kernel by setting this option to @@ -27,6 +41,11 @@ config ARM_UNWIND the performance is not affected. Currently, this feature only works with EABI compilers. If unsure say Y. +config OLD_MCOUNT + bool + depends on FUNCTION_TRACER && FRAME_POINTER + default y + config DEBUG_USER bool "Verbose user fault messages" help diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 59c1ce858fc8b1..b87aed028eeff2 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -173,7 +173,7 @@ machine-$(CONFIG_ARCH_RPC) := rpc machine-$(CONFIG_ARCH_S3C2410) := s3c2410 s3c2400 s3c2412 s3c2416 s3c2440 s3c2443 machine-$(CONFIG_ARCH_S3C24A0) := s3c24a0 machine-$(CONFIG_ARCH_S3C64XX) := s3c64xx -machine-$(CONFIG_ARCH_S5P6440) := s5p6440 +machine-$(CONFIG_ARCH_S5P64X0) := s5p64x0 machine-$(CONFIG_ARCH_S5P6442) := s5p6442 machine-$(CONFIG_ARCH_S5PC100) := s5pc100 machine-$(CONFIG_ARCH_S5PV210) := s5pv210 @@ -183,6 +183,7 @@ machine-$(CONFIG_ARCH_SHARK) := shark machine-$(CONFIG_ARCH_SHMOBILE) := shmobile machine-$(CONFIG_ARCH_STMP378X) := stmp378x machine-$(CONFIG_ARCH_STMP37XX) := stmp37xx +machine-$(CONFIG_ARCH_TCC8K) := tcc8k machine-$(CONFIG_ARCH_TEGRA) := tegra machine-$(CONFIG_ARCH_U300) := u300 machine-$(CONFIG_ARCH_U8500) := ux500 @@ -202,6 +203,7 @@ plat-$(CONFIG_ARCH_MXC) := mxc plat-$(CONFIG_ARCH_OMAP) := omap plat-$(CONFIG_ARCH_S3C64XX) := samsung plat-$(CONFIG_ARCH_STMP3XXX) := stmp3xxx +plat-$(CONFIG_ARCH_TCC_926) := tcc plat-$(CONFIG_PLAT_IOP) := iop plat-$(CONFIG_PLAT_NOMADIK) := nomadik plat-$(CONFIG_PLAT_ORION) := orion @@ -245,13 +247,14 @@ ifeq ($(FASTFPE),$(wildcard $(FASTFPE))) FASTFPE_OBJ :=$(FASTFPE)/ endif -# If we have a machine-specific directory, then include it in the build. -core-y += arch/arm/kernel/ arch/arm/mm/ arch/arm/common/ -core-y += $(machdirs) $(platdirs) core-$(CONFIG_FPE_NWFPE) += arch/arm/nwfpe/ core-$(CONFIG_FPE_FASTFPE) += $(FASTFPE_OBJ) core-$(CONFIG_VFP) += arch/arm/vfp/ +# If we have a machine-specific directory, then include it in the build. +core-y += arch/arm/kernel/ arch/arm/mm/ arch/arm/common/ +core-y += $(machdirs) $(platdirs) + drivers-$(CONFIG_OPROFILE) += arch/arm/oprofile/ libs-y := arch/arm/lib/ $(libs-y) diff --git a/arch/arm/common/gic.c b/arch/arm/common/gic.c index 7dfa9a85bc0c87..ada6359160ebef 100644 --- a/arch/arm/common/gic.c +++ b/arch/arm/common/gic.c @@ -67,25 +67,11 @@ static inline unsigned int gic_irq(unsigned int irq) /* * Routines to acknowledge, disable and enable interrupts - * - * Linux assumes that when we're done with an interrupt we need to - * unmask it, in the same way we need to unmask an interrupt when - * we first enable it. - * - * The GIC has a separate notion of "end of interrupt" to re-enable - * an interrupt after handling, in order to support hardware - * prioritisation. - * - * We can make the GIC behave in the way that Linux expects by making - * our "acknowledge" routine disable the interrupt, then mark it as - * complete. */ static void gic_ack_irq(unsigned int irq) { - u32 mask = 1 << (irq % 32); spin_lock(&irq_controller_lock); - writel(mask, gic_dist_base(irq) + GIC_DIST_ENABLE_CLEAR + (gic_irq(irq) / 32) * 4); writel(gic_irq(irq), gic_cpu_base(irq) + GIC_CPU_EOI); spin_unlock(&irq_controller_lock); } diff --git a/arch/arm/common/pl330.c b/arch/arm/common/pl330.c index 5ebbab6242a78c..8f0f86db36024e 100644 --- a/arch/arm/common/pl330.c +++ b/arch/arm/common/pl330.c @@ -146,8 +146,7 @@ #define DESIGNER 0x41 #define REVISION 0x0 #define INTEG_CFG 0x0 -#define PERIPH_ID_VAL ((PART << 0) | (DESIGNER << 12) \ - | (REVISION << 20) | (INTEG_CFG << 24)) +#define PERIPH_ID_VAL ((PART << 0) | (DESIGNER << 12)) #define PCELL_ID_VAL 0xb105f00d @@ -1859,10 +1858,10 @@ int pl330_add(struct pl330_info *pi) regs = pi->base; /* Check if we can handle this DMAC */ - if (get_id(pi, PERIPH_ID) != PERIPH_ID_VAL + if ((get_id(pi, PERIPH_ID) & 0xfffff) != PERIPH_ID_VAL || get_id(pi, PCELL_ID) != PCELL_ID_VAL) { dev_err(pi->dev, "PERIPH_ID 0x%x, PCELL_ID 0x%x !\n", - readl(regs + PERIPH_ID), readl(regs + PCELL_ID)); + get_id(pi, PERIPH_ID), get_id(pi, PCELL_ID)); return -EINVAL; } diff --git a/arch/arm/common/sa1111.c b/arch/arm/common/sa1111.c index 517d50ddbeb315..c0258a8c103bd4 100644 --- a/arch/arm/common/sa1111.c +++ b/arch/arm/common/sa1111.c @@ -678,7 +678,7 @@ sa1111_init_one_child(struct sa1111 *sachip, struct resource *parent, * %-EBUSY physical address already marked in-use. * %0 successful. */ -static int +static int __devinit __sa1111_probe(struct device *me, struct resource *mem, int irq) { struct sa1111 *sachip; diff --git a/arch/arm/configs/at91sam9g20ek_defconfig b/arch/arm/configs/at91sam9g20ek_defconfig index f1bac70d6ce95f..9e90e6d7929730 100644 --- a/arch/arm/configs/at91sam9g20ek_defconfig +++ b/arch/arm/configs/at91sam9g20ek_defconfig @@ -13,6 +13,7 @@ CONFIG_MODULE_UNLOAD=y CONFIG_ARCH_AT91=y CONFIG_ARCH_AT91SAM9G20=y CONFIG_MACH_AT91SAM9G20EK=y +CONFIG_MACH_AT91SAM9G20EK_2MMC=y CONFIG_AT91_PROGRAMMABLE_CLOCKS=y # CONFIG_ARM_THUMB is not set CONFIG_AEABI=y diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig index ccc9c9959b82ba..2f7042813765f7 100644 --- a/arch/arm/configs/kirkwood_defconfig +++ b/arch/arm/configs/kirkwood_defconfig @@ -15,6 +15,7 @@ CONFIG_MACH_MV88F6281GTW_GE=y CONFIG_MACH_SHEEVAPLUG=y CONFIG_MACH_ESATA_SHEEVAPLUG=y CONFIG_MACH_GURUPLUG=y +CONFIG_MACH_DOCKSTAR=y CONFIG_MACH_TS219=y CONFIG_MACH_TS41X=y CONFIG_MACH_OPENRD_BASE=y diff --git a/arch/arm/configs/mx27_defconfig b/arch/arm/configs/mx27_defconfig index b2038b0e266f35..813cfb366c1830 100644 --- a/arch/arm/configs/mx27_defconfig +++ b/arch/arm/configs/mx27_defconfig @@ -21,8 +21,14 @@ CONFIG_ARCH_MX2=y CONFIG_MACH_MX27=y CONFIG_MACH_MX27ADS=y CONFIG_MACH_PCM038=y +CONFIG_MACH_CPUIMX27=y +CONFIG_MACH_EUKREA_CPUIMX27_USESDHC2=y +CONFIG_MACH_EUKREA_CPUIMX27_USEUART4=y CONFIG_MACH_MX27_3DS=y +CONFIG_MACH_IMX27_VISSTRIM_M10=y CONFIG_MACH_IMX27LITE=y +CONFIG_MACH_PCA100=y +CONFIG_MACH_MXT_TD60=y CONFIG_MXC_IRQ_PRIOR=y CONFIG_MXC_PWM=y CONFIG_NO_HZ=y @@ -76,7 +82,9 @@ CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_KEYBOARD is not set # CONFIG_INPUT_MOUSE is not set CONFIG_INPUT_TOUCHSCREEN=y +CONFIG_TOUCHSCREEN_ADS7846=m # CONFIG_SERIO is not set +CONFIG_SERIAL_8250=m CONFIG_SERIAL_IMX=y CONFIG_SERIAL_IMX_CONSOLE=y # CONFIG_LEGACY_PTYS is not set @@ -85,19 +93,20 @@ CONFIG_I2C=y CONFIG_I2C_CHARDEV=y CONFIG_I2C_IMX=y CONFIG_SPI=y -CONFIG_SPI_BITBANG=y +CONFIG_SPI_IMX=y CONFIG_W1=y CONFIG_W1_MASTER_MXC=y CONFIG_W1_SLAVE_THERM=y # CONFIG_HWMON is not set CONFIG_FB=y CONFIG_FB_IMX=y -# CONFIG_VGA_CONSOLE is not set CONFIG_FRAMEBUFFER_CONSOLE=y CONFIG_FONTS=y CONFIG_FONT_8x8=y # CONFIG_HID_SUPPORT is not set -# CONFIG_USB_SUPPORT is not set +CONFIG_USB=m +# CONFIG_USB_DEVICE_CLASS is not set +CONFIG_USB_ULPI=y CONFIG_MMC=y CONFIG_MMC_MXC=y CONFIG_RTC_CLASS=y diff --git a/arch/arm/configs/mx31pdk_defconfig b/arch/arm/configs/mx31pdk_defconfig deleted file mode 100644 index 2d29329749e4e2..00000000000000 --- a/arch/arm/configs/mx31pdk_defconfig +++ /dev/null @@ -1,44 +0,0 @@ -# CONFIG_LOCALVERSION_AUTO is not set -# CONFIG_SWAP is not set -# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set -# CONFIG_COMPAT_BRK is not set -# CONFIG_IOSCHED_DEADLINE is not set -# CONFIG_IOSCHED_CFQ is not set -CONFIG_ARCH_MXC=y -# CONFIG_MACH_MX31ADS is not set -CONFIG_MACH_MX31_3DS=y -CONFIG_AEABI=y -CONFIG_NET=y -CONFIG_PACKET=y -CONFIG_UNIX=y -CONFIG_NET_KEY=y -CONFIG_INET=y -CONFIG_IP_PNP=y -CONFIG_IP_PNP_DHCP=y -# CONFIG_INET_LRO is not set -CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" -# CONFIG_PREVENT_FIRMWARE_BUILD is not set -# CONFIG_FIRMWARE_IN_KERNEL is not set -# CONFIG_BLK_DEV is not set -# CONFIG_MISC_DEVICES is not set -CONFIG_NETDEVICES=y -CONFIG_NET_ETHERNET=y -# CONFIG_INPUT_MOUSEDEV_PSAUX is not set -# CONFIG_INPUT_KEYBOARD is not set -# CONFIG_INPUT_MOUSE is not set -# CONFIG_SERIO is not set -# CONFIG_DEVKMEM is not set -CONFIG_SERIAL_IMX=y -CONFIG_SERIAL_IMX_CONSOLE=y -# CONFIG_LEGACY_PTYS is not set -# CONFIG_HW_RANDOM is not set -# CONFIG_HWMON is not set -# CONFIG_VGA_CONSOLE is not set -# CONFIG_HID_SUPPORT is not set -# CONFIG_USB_SUPPORT is not set -# CONFIG_DNOTIFY is not set -# CONFIG_ENABLE_WARN_DEPRECATED is not set -# CONFIG_ENABLE_MUST_CHECK is not set -# CONFIG_RCU_CPU_STALL_DETECTOR is not set -# CONFIG_CRYPTO_ANSI_CPRNG is not set -# CONFIG_CRC32 is not set diff --git a/arch/arm/configs/mx3_defconfig b/arch/arm/configs/mx3_defconfig index 161f907b611f38..f0c339fd5d2137 100644 --- a/arch/arm/configs/mx3_defconfig +++ b/arch/arm/configs/mx3_defconfig @@ -24,6 +24,7 @@ CONFIG_MACH_PCM043=y CONFIG_MACH_ARMADILLO5X0=y CONFIG_MACH_MX35_3DS=y CONFIG_MACH_KZM_ARM11_01=y +CONFIG_MACH_EUKREA_CPUIMX35=y CONFIG_MXC_IRQ_PRIOR=y CONFIG_MXC_PWM=y CONFIG_NO_HZ=y @@ -108,7 +109,6 @@ CONFIG_MMC=y CONFIG_MMC_MXC=y CONFIG_DMADEVICES=y # CONFIG_DNOTIFY is not set -CONFIG_INOTIFY=y CONFIG_TMPFS=y CONFIG_JFFS2_FS=y CONFIG_UBIFS_FS=y diff --git a/arch/arm/configs/mx51_defconfig b/arch/arm/configs/mx51_defconfig index a665ecbbe2bc2b..163cfee7644c72 100644 --- a/arch/arm/configs/mx51_defconfig +++ b/arch/arm/configs/mx51_defconfig @@ -15,6 +15,8 @@ CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_ARCH_MXC=y CONFIG_ARCH_MX5=y CONFIG_MACH_MX51_BABBAGE=y +CONFIG_MACH_MX51_3DS=y +CONFIG_MACH_EUKREA_CPUIMX51=y CONFIG_NO_HZ=y CONFIG_HIGH_RES_TIMERS=y CONFIG_PREEMPT_VOLUNTARY=y @@ -69,7 +71,6 @@ CONFIG_REALTEK_PHY=y CONFIG_NATIONAL_PHY=y CONFIG_STE10XP=y CONFIG_LSI_ET1011C_PHY=y -CONFIG_FIXED_PHY=y CONFIG_MDIO_BITBANG=y CONFIG_MDIO_GPIO=y CONFIG_NET_ETHERNET=y @@ -100,7 +101,6 @@ CONFIG_I2C_ALGOPCF=m CONFIG_I2C_ALGOPCA=m CONFIG_GPIO_SYSFS=y # CONFIG_HWMON is not set -# CONFIG_VGA_CONSOLE is not set # CONFIG_HID_SUPPORT is not set CONFIG_USB=y CONFIG_USB_EHCI_HCD=y @@ -117,13 +117,11 @@ CONFIG_EXT2_FS_XATTR=y CONFIG_EXT2_FS_POSIX_ACL=y CONFIG_EXT2_FS_SECURITY=y CONFIG_EXT3_FS=y -CONFIG_EXT3_DEFAULTS_TO_ORDERED=y CONFIG_EXT3_FS_POSIX_ACL=y CONFIG_EXT3_FS_SECURITY=y CONFIG_EXT4_FS=y CONFIG_EXT4_FS_POSIX_ACL=y CONFIG_EXT4_FS_SECURITY=y -CONFIG_INOTIFY=y CONFIG_QUOTA=y CONFIG_QUOTA_NETLINK_INTERFACE=y # CONFIG_PRINT_QUOTA_WARNING is not set @@ -136,6 +134,7 @@ CONFIG_ZISOFS=y CONFIG_UDF_FS=m CONFIG_MSDOS_FS=m CONFIG_VFAT_FS=y +CONFIG_TMPFS=y CONFIG_CONFIGFS_FS=m CONFIG_NFS_FS=y CONFIG_NFS_V3=y @@ -151,7 +150,6 @@ CONFIG_NLS_UTF8=y CONFIG_MAGIC_SYSRQ=y CONFIG_DEBUG_FS=y CONFIG_DEBUG_KERNEL=y -# CONFIG_DETECT_SOFTLOCKUP is not set # CONFIG_SCHED_DEBUG is not set # CONFIG_DEBUG_BUGVERBOSE is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set @@ -159,7 +157,6 @@ CONFIG_DEBUG_KERNEL=y # CONFIG_ARM_UNWIND is not set CONFIG_DEBUG_LL=y CONFIG_EARLY_PRINTK=y -CONFIG_KEYS=y CONFIG_SECURITYFS=y CONFIG_CRYPTO_DEFLATE=y CONFIG_CRYPTO_LZO=y diff --git a/arch/arm/configs/realview-smp_defconfig b/arch/arm/configs/realview-smp_defconfig index 9312ef9f9bf42b..5ca7a61f7c01d6 100644 --- a/arch/arm/configs/realview-smp_defconfig +++ b/arch/arm/configs/realview-smp_defconfig @@ -39,6 +39,7 @@ CONFIG_MTD_CFI=y CONFIG_MTD_CFI_INTELEXT=y CONFIG_MTD_CFI_AMDSTD=y CONFIG_MTD_ARM_INTEGRATOR=y +CONFIG_ARM_CHARLCD=y CONFIG_NETDEVICES=y CONFIG_SMSC_PHY=y CONFIG_NET_ETHERNET=y @@ -52,10 +53,13 @@ CONFIG_SERIAL_AMBA_PL011=y CONFIG_SERIAL_AMBA_PL011_CONSOLE=y CONFIG_LEGACY_PTY_COUNT=16 # CONFIG_HW_RANDOM is not set +CONFIG_I2C=y +CONFIG_I2C_VERSATILE=y +CONFIG_SPI=y +CONFIG_GPIOLIB=y # CONFIG_HWMON is not set CONFIG_FB=y CONFIG_FB_ARMCLCD=y -# CONFIG_VGA_CONSOLE is not set CONFIG_FRAMEBUFFER_CONSOLE=y CONFIG_LOGO=y # CONFIG_LOGO_LINUX_MONO is not set @@ -70,7 +74,13 @@ CONFIG_SND_ARMAACI=y # CONFIG_USB_SUPPORT is not set CONFIG_MMC=y CONFIG_MMC_ARMMMCI=y -CONFIG_INOTIFY=y +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=y +CONFIG_LEDS_TRIGGERS=y +CONFIG_LEDS_TRIGGER_HEARTBEAT=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_DRV_DS1307=y +CONFIG_RTC_DRV_PL031=y CONFIG_VFAT_FS=y CONFIG_TMPFS=y CONFIG_CRAMFS=y @@ -80,6 +90,7 @@ CONFIG_ROOT_NFS=y CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ISO8859_1=y CONFIG_MAGIC_SYSRQ=y +CONFIG_DEBUG_FS=y CONFIG_DEBUG_KERNEL=y # CONFIG_SCHED_DEBUG is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set diff --git a/arch/arm/configs/realview_defconfig b/arch/arm/configs/realview_defconfig index fb75192ee7e5af..fcaa6032805125 100644 --- a/arch/arm/configs/realview_defconfig +++ b/arch/arm/configs/realview_defconfig @@ -38,6 +38,7 @@ CONFIG_MTD_CFI=y CONFIG_MTD_CFI_INTELEXT=y CONFIG_MTD_CFI_AMDSTD=y CONFIG_MTD_ARM_INTEGRATOR=y +CONFIG_ARM_CHARLCD=y CONFIG_NETDEVICES=y CONFIG_SMSC_PHY=y CONFIG_NET_ETHERNET=y @@ -51,10 +52,13 @@ CONFIG_SERIAL_AMBA_PL011=y CONFIG_SERIAL_AMBA_PL011_CONSOLE=y CONFIG_LEGACY_PTY_COUNT=16 # CONFIG_HW_RANDOM is not set +CONFIG_I2C=y +CONFIG_I2C_VERSATILE=y +CONFIG_SPI=y +CONFIG_GPIOLIB=y # CONFIG_HWMON is not set CONFIG_FB=y CONFIG_FB_ARMCLCD=y -# CONFIG_VGA_CONSOLE is not set CONFIG_FRAMEBUFFER_CONSOLE=y CONFIG_LOGO=y # CONFIG_LOGO_LINUX_MONO is not set @@ -69,7 +73,13 @@ CONFIG_SND_ARMAACI=y # CONFIG_USB_SUPPORT is not set CONFIG_MMC=y CONFIG_MMC_ARMMMCI=y -CONFIG_INOTIFY=y +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=y +CONFIG_LEDS_TRIGGERS=y +CONFIG_LEDS_TRIGGER_HEARTBEAT=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_DRV_DS1307=y +CONFIG_RTC_DRV_PL031=y CONFIG_VFAT_FS=y CONFIG_TMPFS=y CONFIG_CRAMFS=y @@ -79,6 +89,7 @@ CONFIG_ROOT_NFS=y CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ISO8859_1=y CONFIG_MAGIC_SYSRQ=y +CONFIG_DEBUG_FS=y CONFIG_DEBUG_KERNEL=y # CONFIG_SCHED_DEBUG is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set diff --git a/arch/arm/configs/s5p6440_defconfig b/arch/arm/configs/s5p64x0_defconfig similarity index 97% rename from arch/arm/configs/s5p6440_defconfig rename to arch/arm/configs/s5p64x0_defconfig index 0b0266c6d32695..2993ecd3514526 100644 --- a/arch/arm/configs/s5p6440_defconfig +++ b/arch/arm/configs/s5p64x0_defconfig @@ -5,10 +5,11 @@ CONFIG_KALLSYMS_ALL=y CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_BLK_DEV_BSG is not set -CONFIG_ARCH_S5P6440=y +CONFIG_ARCH_S5P64X0=y CONFIG_S3C_BOOT_ERROR_RESET=y CONFIG_S3C_LOWLEVEL_UART_PORT=1 CONFIG_MACH_SMDK6440=y +CONFIG_MACH_SMDK6450=y CONFIG_CPU_32v6K=y CONFIG_AEABI=y CONFIG_CMDLINE="root=/dev/ram0 rw ramdisk=8192 initrd=0x20800000,8M console=ttySAC1,115200 init=/linuxrc" diff --git a/arch/arm/configs/u300_defconfig b/arch/arm/configs/u300_defconfig index 46e5e0747269be..c1c252cdca6070 100644 --- a/arch/arm/configs/u300_defconfig +++ b/arch/arm/configs/u300_defconfig @@ -28,26 +28,9 @@ CONFIG_CPU_IDLE=y CONFIG_FPE_NWFPE=y CONFIG_PM=y # CONFIG_SUSPEND is not set -CONFIG_NET=y -CONFIG_PACKET=y -CONFIG_UNIX=y -CONFIG_INET=y -# CONFIG_INET_XFRM_MODE_TRANSPORT is not set -# CONFIG_INET_XFRM_MODE_TUNNEL is not set -# CONFIG_INET_XFRM_MODE_BEET is not set -# CONFIG_INET_LRO is not set -# CONFIG_INET_DIAG is not set -# CONFIG_IPV6 is not set -# CONFIG_WIRELESS is not set CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" # CONFIG_PREVENT_FIRMWARE_BUILD is not set -CONFIG_MTD=y -CONFIG_MTD_PARTITIONS=y -CONFIG_MTD_CMDLINE_PARTS=y -CONFIG_MTD_CHAR=y -CONFIG_MTD_BLOCK=y -CONFIG_MTD_NAND=y -CONFIG_MTD_NAND_ECC_SMC=y +# CONFIG_MISC_DEVICES is not set # CONFIG_INPUT_MOUSEDEV is not set CONFIG_INPUT_EVDEV=y # CONFIG_KEYBOARD_ATKBD is not set @@ -58,7 +41,6 @@ CONFIG_SERIAL_AMBA_PL011_CONSOLE=y CONFIG_LEGACY_PTY_COUNT=16 # CONFIG_HW_RANDOM is not set CONFIG_I2C=y -CONFIG_POWER_SUPPLY=y # CONFIG_HWMON is not set CONFIG_WATCHDOG=y CONFIG_REGULATOR=y @@ -66,24 +48,10 @@ CONFIG_FB=y CONFIG_BACKLIGHT_LCD_SUPPORT=y # CONFIG_LCD_CLASS_DEVICE is not set CONFIG_BACKLIGHT_CLASS_DEVICE=y -# CONFIG_VGA_CONSOLE is not set -CONFIG_SOUND=y -CONFIG_SND=y -# CONFIG_SND_SUPPORT_OLD_API is not set -# CONFIG_SND_VERBOSE_PROCFS is not set -# CONFIG_SND_DRIVERS is not set -# CONFIG_SND_ARM is not set -# CONFIG_SND_SPI is not set -CONFIG_SND_SOC=y # CONFIG_HID_SUPPORT is not set # CONFIG_USB_SUPPORT is not set CONFIG_MMC=y -CONFIG_MMC_DEBUG=y CONFIG_MMC_ARMMMCI=y -CONFIG_NEW_LEDS=y -CONFIG_LEDS_CLASS=y -CONFIG_LEDS_TRIGGERS=y -CONFIG_LEDS_TRIGGER_BACKLIGHT=y CONFIG_RTC_CLASS=y # CONFIG_RTC_HCTOSYS is not set CONFIG_RTC_DRV_COH901331=y @@ -93,12 +61,11 @@ CONFIG_COH901318=y CONFIG_FUSE_FS=y CONFIG_VFAT_FS=y CONFIG_TMPFS=y -# CONFIG_NETWORK_FILESYSTEMS is not set CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ISO8859_1=y CONFIG_PRINTK_TIME=y +CONFIG_DEBUG_FS=y CONFIG_DEBUG_KERNEL=y -# CONFIG_DETECT_SOFTLOCKUP is not set # CONFIG_SCHED_DEBUG is not set CONFIG_TIMER_STATS=y # CONFIG_DEBUG_PREEMPT is not set diff --git a/arch/arm/include/asm/assembler.h b/arch/arm/include/asm/assembler.h index 6e8f05c8a1c8f6..062b58c029ab92 100644 --- a/arch/arm/include/asm/assembler.h +++ b/arch/arm/include/asm/assembler.h @@ -154,16 +154,39 @@ .long 9999b,9001f; \ .popsection +#ifdef CONFIG_SMP +#define ALT_SMP(instr...) \ +9998: instr +#define ALT_UP(instr...) \ + .pushsection ".alt.smp.init", "a" ;\ + .long 9998b ;\ + instr ;\ + .popsection +#define ALT_UP_B(label) \ + .equ up_b_offset, label - 9998b ;\ + .pushsection ".alt.smp.init", "a" ;\ + .long 9998b ;\ + b . + up_b_offset ;\ + .popsection +#else +#define ALT_SMP(instr...) +#define ALT_UP(instr...) instr +#define ALT_UP_B(label) b label +#endif + /* * SMP data memory barrier */ .macro smp_dmb #ifdef CONFIG_SMP #if __LINUX_ARM_ARCH__ >= 7 - dmb + ALT_SMP(dmb) #elif __LINUX_ARM_ARCH__ == 6 - mcr p15, 0, r0, c7, c10, 5 @ dmb + ALT_SMP(mcr p15, 0, r0, c7, c10, 5) @ dmb +#else +#error Incompatible SMP platform #endif + ALT_UP(nop) #endif .endm diff --git a/arch/arm/include/asm/cacheflush.h b/arch/arm/include/asm/cacheflush.h index 4656a24058d21f..3acd8fa25e347d 100644 --- a/arch/arm/include/asm/cacheflush.h +++ b/arch/arm/include/asm/cacheflush.h @@ -137,10 +137,10 @@ #endif /* - * This flag is used to indicate that the page pointed to by a pte - * is dirty and requires cleaning before returning it to the user. + * This flag is used to indicate that the page pointed to by a pte is clean + * and does not require cleaning before returning it to the user. */ -#define PG_dcache_dirty PG_arch_1 +#define PG_dcache_clean PG_arch_1 /* * MM Cache Management @@ -156,6 +156,12 @@ * Please note that the implementation of these, and the required * effects are cache-type (VIVT/VIPT/PIPT) specific. * + * flush_icache_all() + * + * Unconditionally clean and invalidate the entire icache. + * Currently only needed for cache-v6.S and cache-v7.S, see + * __flush_icache_all for the generic implementation. + * * flush_kern_all() * * Unconditionally clean and invalidate the entire cache. @@ -206,6 +212,7 @@ */ struct cpu_cache_fns { + void (*flush_icache_all)(void); void (*flush_kern_all)(void); void (*flush_user_all)(void); void (*flush_user_range)(unsigned long, unsigned long, unsigned int); @@ -227,6 +234,7 @@ struct cpu_cache_fns { extern struct cpu_cache_fns cpu_cache; +#define __cpuc_flush_icache_all cpu_cache.flush_icache_all #define __cpuc_flush_kern_all cpu_cache.flush_kern_all #define __cpuc_flush_user_all cpu_cache.flush_user_all #define __cpuc_flush_user_range cpu_cache.flush_user_range @@ -246,6 +254,7 @@ extern struct cpu_cache_fns cpu_cache; #else +#define __cpuc_flush_icache_all __glue(_CACHE,_flush_icache_all) #define __cpuc_flush_kern_all __glue(_CACHE,_flush_kern_cache_all) #define __cpuc_flush_user_all __glue(_CACHE,_flush_user_cache_all) #define __cpuc_flush_user_range __glue(_CACHE,_flush_user_cache_range) @@ -253,6 +262,7 @@ extern struct cpu_cache_fns cpu_cache; #define __cpuc_coherent_user_range __glue(_CACHE,_coherent_user_range) #define __cpuc_flush_dcache_area __glue(_CACHE,_flush_kern_dcache_area) +extern void __cpuc_flush_icache_all(void); extern void __cpuc_flush_kern_all(void); extern void __cpuc_flush_user_all(void); extern void __cpuc_flush_user_range(unsigned long, unsigned long, unsigned int); @@ -291,6 +301,37 @@ extern void copy_to_user_page(struct vm_area_struct *, struct page *, /* * Convert calls to our calling convention. */ + +/* Invalidate I-cache */ +#define __flush_icache_all_generic() \ + asm("mcr p15, 0, %0, c7, c5, 0" \ + : : "r" (0)); + +/* Invalidate I-cache inner shareable */ +#define __flush_icache_all_v7_smp() \ + asm("mcr p15, 0, %0, c7, c1, 0" \ + : : "r" (0)); + +/* + * Optimized __flush_icache_all for the common cases. Note that UP ARMv7 + * will fall through to use __flush_icache_all_generic. + */ +#if (defined(CONFIG_CPU_V7) && defined(CONFIG_CPU_V6)) || \ + defined(CONFIG_SMP_ON_UP) +#define __flush_icache_preferred __cpuc_flush_icache_all +#elif __LINUX_ARM_ARCH__ >= 7 && defined(CONFIG_SMP) +#define __flush_icache_preferred __flush_icache_all_v7_smp +#elif __LINUX_ARM_ARCH__ == 6 && defined(CONFIG_ARM_ERRATA_411920) +#define __flush_icache_preferred __cpuc_flush_icache_all +#else +#define __flush_icache_preferred __flush_icache_all_generic +#endif + +static inline void __flush_icache_all(void) +{ + __flush_icache_preferred(); +} + #define flush_cache_all() __cpuc_flush_kern_all() static inline void vivt_flush_cache_mm(struct mm_struct *mm) @@ -366,21 +407,6 @@ extern void flush_cache_page(struct vm_area_struct *vma, unsigned long user_addr #define ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE 1 extern void flush_dcache_page(struct page *); -static inline void __flush_icache_all(void) -{ -#ifdef CONFIG_ARM_ERRATA_411920 - extern void v6_icache_inval_all(void); - v6_icache_inval_all(); -#elif defined(CONFIG_SMP) && __LINUX_ARM_ARCH__ >= 7 - asm("mcr p15, 0, %0, c7, c1, 0 @ invalidate I-cache inner shareable\n" - : - : "r" (0)); -#else - asm("mcr p15, 0, %0, c7, c5, 0 @ invalidate I-cache\n" - : - : "r" (0)); -#endif -} static inline void flush_kernel_vmap_range(void *addr, int size) { if ((cache_is_vivt() || cache_is_vipt_aliasing())) @@ -405,9 +431,6 @@ static inline void flush_anon_page(struct vm_area_struct *vma, #define ARCH_HAS_FLUSH_KERNEL_DCACHE_PAGE static inline void flush_kernel_dcache_page(struct page *page) { - /* highmem pages are always flushed upon kunmap already */ - if ((cache_is_vivt() || cache_is_vipt_aliasing()) && !PageHighMem(page)) - __cpuc_flush_dcache_area(page_address(page), PAGE_SIZE); } #define flush_dcache_mmap_lock(mapping) \ diff --git a/arch/arm/include/asm/cachetype.h b/arch/arm/include/asm/cachetype.h index d3a4c2cb9f2f66..c023db09fcc14c 100644 --- a/arch/arm/include/asm/cachetype.h +++ b/arch/arm/include/asm/cachetype.h @@ -6,6 +6,7 @@ #define CACHEID_VIPT_ALIASING (1 << 2) #define CACHEID_VIPT (CACHEID_VIPT_ALIASING|CACHEID_VIPT_NONALIASING) #define CACHEID_ASID_TAGGED (1 << 3) +#define CACHEID_VIPT_I_ALIASING (1 << 4) extern unsigned int cacheid; @@ -14,15 +15,18 @@ extern unsigned int cacheid; #define cache_is_vipt_nonaliasing() cacheid_is(CACHEID_VIPT_NONALIASING) #define cache_is_vipt_aliasing() cacheid_is(CACHEID_VIPT_ALIASING) #define icache_is_vivt_asid_tagged() cacheid_is(CACHEID_ASID_TAGGED) +#define icache_is_vipt_aliasing() cacheid_is(CACHEID_VIPT_I_ALIASING) /* * __LINUX_ARM_ARCH__ is the minimum supported CPU architecture * Mask out support which will never be present on newer CPUs. * - v6+ is never VIVT - * - v7+ VIPT never aliases + * - v7+ VIPT never aliases on D-side */ #if __LINUX_ARM_ARCH__ >= 7 -#define __CACHEID_ARCH_MIN (CACHEID_VIPT_NONALIASING | CACHEID_ASID_TAGGED) +#define __CACHEID_ARCH_MIN (CACHEID_VIPT_NONALIASING |\ + CACHEID_ASID_TAGGED |\ + CACHEID_VIPT_I_ALIASING) #elif __LINUX_ARM_ARCH__ >= 6 #define __CACHEID_ARCH_MIN (~CACHEID_VIVT) #else diff --git a/arch/arm/include/asm/elf.h b/arch/arm/include/asm/elf.h index 5747a8baa4135b..8bb66bca2e3eb8 100644 --- a/arch/arm/include/asm/elf.h +++ b/arch/arm/include/asm/elf.h @@ -127,4 +127,8 @@ struct mm_struct; extern unsigned long arch_randomize_brk(struct mm_struct *mm); #define arch_randomize_brk arch_randomize_brk +extern int vectors_user_mapping(void); +#define arch_setup_additional_pages(bprm, uses_interp) vectors_user_mapping() +#define ARCH_HAS_SETUP_ADDITIONAL_PAGES + #endif diff --git a/arch/arm/include/asm/ftrace.h b/arch/arm/include/asm/ftrace.h index 103f7ee9731357..f89515adac60ef 100644 --- a/arch/arm/include/asm/ftrace.h +++ b/arch/arm/include/asm/ftrace.h @@ -2,12 +2,30 @@ #define _ASM_ARM_FTRACE #ifdef CONFIG_FUNCTION_TRACER -#define MCOUNT_ADDR ((long)(mcount)) +#define MCOUNT_ADDR ((unsigned long)(__gnu_mcount_nc)) #define MCOUNT_INSN_SIZE 4 /* sizeof mcount call */ #ifndef __ASSEMBLY__ extern void mcount(void); extern void __gnu_mcount_nc(void); + +#ifdef CONFIG_DYNAMIC_FTRACE +struct dyn_arch_ftrace { +#ifdef CONFIG_OLD_MCOUNT + bool old_mcount; +#endif +}; + +static inline unsigned long ftrace_call_adjust(unsigned long addr) +{ + /* With Thumb-2, the recorded addresses have the lsb set */ + return addr & ~1; +} + +extern void ftrace_caller_old(void); +extern void ftrace_call_old(void); +#endif + #endif #endif diff --git a/arch/arm/include/asm/hardware/coresight.h b/arch/arm/include/asm/hardware/coresight.h index 212e47828c791e..7ecd793b8f5a94 100644 --- a/arch/arm/include/asm/hardware/coresight.h +++ b/arch/arm/include/asm/hardware/coresight.h @@ -21,18 +21,6 @@ #define TRACER_RUNNING BIT(TRACER_RUNNING_BIT) #define TRACER_CYCLE_ACC BIT(TRACER_CYCLE_ACC_BIT) -struct tracectx { - unsigned int etb_bufsz; - void __iomem *etb_regs; - void __iomem *etm_regs; - unsigned long flags; - int ncmppairs; - int etm_portsz; - struct device *dev; - struct clk *emu_clk; - struct mutex mutex; -}; - #define TRACER_TIMEOUT 10000 #define etm_writel(t, v, x) \ @@ -112,10 +100,10 @@ struct tracectx { /* ETM status register, "ETM Architecture", 3.3.2 */ #define ETMR_STATUS (0x10) -#define ETMST_OVERFLOW (1 << 0) -#define ETMST_PROGBIT (1 << 1) -#define ETMST_STARTSTOP (1 << 2) -#define ETMST_TRIGGER (1 << 3) +#define ETMST_OVERFLOW BIT(0) +#define ETMST_PROGBIT BIT(1) +#define ETMST_STARTSTOP BIT(2) +#define ETMST_TRIGGER BIT(3) #define etm_progbit(t) (etm_readl((t), ETMR_STATUS) & ETMST_PROGBIT) #define etm_started(t) (etm_readl((t), ETMR_STATUS) & ETMST_STARTSTOP) @@ -123,7 +111,7 @@ struct tracectx { #define ETMR_TRACEENCTRL2 0x1c #define ETMR_TRACEENCTRL 0x24 -#define ETMTE_INCLEXCL (1 << 24) +#define ETMTE_INCLEXCL BIT(24) #define ETMR_TRACEENEVT 0x20 #define ETMCTRL_OPTS (ETMCTRL_DO_CPRT | \ ETMCTRL_DATA_DO_ADDR | \ @@ -146,12 +134,12 @@ struct tracectx { #define ETBR_CTRL 0x20 #define ETBR_FORMATTERCTRL 0x304 #define ETBFF_ENFTC 1 -#define ETBFF_ENFCONT (1 << 1) -#define ETBFF_FONFLIN (1 << 4) -#define ETBFF_MANUAL_FLUSH (1 << 6) -#define ETBFF_TRIGIN (1 << 8) -#define ETBFF_TRIGEVT (1 << 9) -#define ETBFF_TRIGFL (1 << 10) +#define ETBFF_ENFCONT BIT(1) +#define ETBFF_FONFLIN BIT(4) +#define ETBFF_MANUAL_FLUSH BIT(6) +#define ETBFF_TRIGIN BIT(8) +#define ETBFF_TRIGEVT BIT(9) +#define ETBFF_TRIGFL BIT(10) #define etb_writel(t, v, x) \ (__raw_writel((v), (t)->etb_regs + (x))) diff --git a/arch/arm/include/asm/hw_breakpoint.h b/arch/arm/include/asm/hw_breakpoint.h new file mode 100644 index 00000000000000..4d8ae9d67abef5 --- /dev/null +++ b/arch/arm/include/asm/hw_breakpoint.h @@ -0,0 +1,133 @@ +#ifndef _ARM_HW_BREAKPOINT_H +#define _ARM_HW_BREAKPOINT_H + +#ifdef __KERNEL__ + +struct task_struct; + +#ifdef CONFIG_HAVE_HW_BREAKPOINT + +struct arch_hw_breakpoint_ctrl { + u32 __reserved : 9, + mismatch : 1, + : 9, + len : 8, + type : 2, + privilege : 2, + enabled : 1; +}; + +struct arch_hw_breakpoint { + u32 address; + u32 trigger; + struct perf_event *suspended_wp; + struct arch_hw_breakpoint_ctrl ctrl; +}; + +static inline u32 encode_ctrl_reg(struct arch_hw_breakpoint_ctrl ctrl) +{ + return (ctrl.mismatch << 22) | (ctrl.len << 5) | (ctrl.type << 3) | + (ctrl.privilege << 1) | ctrl.enabled; +} + +static inline void decode_ctrl_reg(u32 reg, + struct arch_hw_breakpoint_ctrl *ctrl) +{ + ctrl->enabled = reg & 0x1; + reg >>= 1; + ctrl->privilege = reg & 0x3; + reg >>= 2; + ctrl->type = reg & 0x3; + reg >>= 2; + ctrl->len = reg & 0xff; + reg >>= 17; + ctrl->mismatch = reg & 0x1; +} + +/* Debug architecture numbers. */ +#define ARM_DEBUG_ARCH_RESERVED 0 /* In case of ptrace ABI updates. */ +#define ARM_DEBUG_ARCH_V6 1 +#define ARM_DEBUG_ARCH_V6_1 2 +#define ARM_DEBUG_ARCH_V7_ECP14 3 +#define ARM_DEBUG_ARCH_V7_MM 4 + +/* Breakpoint */ +#define ARM_BREAKPOINT_EXECUTE 0 + +/* Watchpoints */ +#define ARM_BREAKPOINT_LOAD 1 +#define ARM_BREAKPOINT_STORE 2 + +/* Privilege Levels */ +#define ARM_BREAKPOINT_PRIV 1 +#define ARM_BREAKPOINT_USER 2 + +/* Lengths */ +#define ARM_BREAKPOINT_LEN_1 0x1 +#define ARM_BREAKPOINT_LEN_2 0x3 +#define ARM_BREAKPOINT_LEN_4 0xf +#define ARM_BREAKPOINT_LEN_8 0xff + +/* Limits */ +#define ARM_MAX_BRP 16 +#define ARM_MAX_WRP 16 +#define ARM_MAX_HBP_SLOTS (ARM_MAX_BRP + ARM_MAX_WRP) + +/* DSCR method of entry bits. */ +#define ARM_DSCR_MOE(x) ((x >> 2) & 0xf) +#define ARM_ENTRY_BREAKPOINT 0x1 +#define ARM_ENTRY_ASYNC_WATCHPOINT 0x2 +#define ARM_ENTRY_SYNC_WATCHPOINT 0xa + +/* DSCR monitor/halting bits. */ +#define ARM_DSCR_HDBGEN (1 << 14) +#define ARM_DSCR_MDBGEN (1 << 15) + +/* opcode2 numbers for the co-processor instructions. */ +#define ARM_OP2_BVR 4 +#define ARM_OP2_BCR 5 +#define ARM_OP2_WVR 6 +#define ARM_OP2_WCR 7 + +/* Base register numbers for the debug registers. */ +#define ARM_BASE_BVR 64 +#define ARM_BASE_BCR 80 +#define ARM_BASE_WVR 96 +#define ARM_BASE_WCR 112 + +/* Accessor macros for the debug registers. */ +#define ARM_DBG_READ(M, OP2, VAL) do {\ + asm volatile("mrc p14, 0, %0, c0," #M ", " #OP2 : "=r" (VAL));\ +} while (0) + +#define ARM_DBG_WRITE(M, OP2, VAL) do {\ + asm volatile("mcr p14, 0, %0, c0," #M ", " #OP2 : : "r" (VAL));\ +} while (0) + +struct notifier_block; +struct perf_event; +struct pmu; + +extern struct pmu perf_ops_bp; +extern int arch_bp_generic_fields(struct arch_hw_breakpoint_ctrl ctrl, + int *gen_len, int *gen_type); +extern int arch_check_bp_in_kernelspace(struct perf_event *bp); +extern int arch_validate_hwbkpt_settings(struct perf_event *bp); +extern int hw_breakpoint_exceptions_notify(struct notifier_block *unused, + unsigned long val, void *data); + +extern u8 arch_get_debug_arch(void); +extern u8 arch_get_max_wp_len(void); +extern void clear_ptrace_hw_breakpoint(struct task_struct *tsk); + +int arch_install_hw_breakpoint(struct perf_event *bp); +void arch_uninstall_hw_breakpoint(struct perf_event *bp); +void hw_breakpoint_pmu_read(struct perf_event *bp); +int hw_breakpoint_slots(int type); + +#else +static inline void clear_ptrace_hw_breakpoint(struct task_struct *tsk) {} + +#endif /* CONFIG_HAVE_HW_BREAKPOINT */ +#endif /* __KERNEL__ */ +#endif /* _ARM_HW_BREAKPOINT_H */ diff --git a/arch/arm/include/asm/io.h b/arch/arm/include/asm/io.h index 1261b1f928d95a..815efa2d4e07b5 100644 --- a/arch/arm/include/asm/io.h +++ b/arch/arm/include/asm/io.h @@ -294,6 +294,7 @@ extern void pci_iounmap(struct pci_dev *dev, void __iomem *addr); #define ARCH_HAS_VALID_PHYS_ADDR_RANGE extern int valid_phys_addr_range(unsigned long addr, size_t size); extern int valid_mmap_phys_addr_range(unsigned long pfn, size_t size); +extern int devmem_is_allowed(unsigned long pfn); #endif /* diff --git a/arch/arm/include/asm/mach/arch.h b/arch/arm/include/asm/mach/arch.h index 8a0dd18ba64273..d97a964207fa15 100644 --- a/arch/arm/include/asm/mach/arch.h +++ b/arch/arm/include/asm/mach/arch.h @@ -16,18 +16,15 @@ struct sys_timer; struct machine_desc { /* - * Note! The first four elements are used + * Note! The first two elements are used * by assembler code in head.S, head-common.S */ unsigned int nr; /* architecture number */ - unsigned int nr_irqs; /* number of IRQs */ - unsigned int phys_io; /* start of physical io */ - unsigned int io_pg_offst; /* byte offset for io - * page tabe entry */ - const char *name; /* architecture name */ unsigned long boot_params; /* tagged list */ + unsigned int nr_irqs; /* number of IRQs */ + unsigned int video_start; /* start of video RAM */ unsigned int video_end; /* end of video RAM */ diff --git a/arch/arm/include/asm/mmu_context.h b/arch/arm/include/asm/mmu_context.h index a0b3cac0547c0a..71605d9f8e421a 100644 --- a/arch/arm/include/asm/mmu_context.h +++ b/arch/arm/include/asm/mmu_context.h @@ -18,7 +18,6 @@ #include #include #include -#include void __check_kvm_seq(struct mm_struct *mm); @@ -134,4 +133,32 @@ switch_mm(struct mm_struct *prev, struct mm_struct *next, #define deactivate_mm(tsk,mm) do { } while (0) #define activate_mm(prev,next) switch_mm(prev, next, NULL) +/* + * We are inserting a "fake" vma for the user-accessible vector page so + * gdb and friends can get to it through ptrace and /proc//mem. + * But we also want to remove it before the generic code gets to see it + * during process exit or the unmapping of it would cause total havoc. + * (the macro is used as remove_vma() is static to mm/mmap.c) + */ +#define arch_exit_mmap(mm) \ +do { \ + struct vm_area_struct *high_vma = find_vma(mm, 0xffff0000); \ + if (high_vma) { \ + BUG_ON(high_vma->vm_next); /* it should be last */ \ + if (high_vma->vm_prev) \ + high_vma->vm_prev->vm_next = NULL; \ + else \ + mm->mmap = NULL; \ + rb_erase(&high_vma->vm_rb, &mm->mm_rb); \ + mm->mmap_cache = NULL; \ + mm->map_count--; \ + remove_vma(high_vma); \ + } \ +} while (0) + +static inline void arch_dup_mmap(struct mm_struct *oldmm, + struct mm_struct *mm) +{ +} + #endif diff --git a/arch/arm/include/asm/module.h b/arch/arm/include/asm/module.h index e4dfa69abb68fa..cbb0bc295d2b18 100644 --- a/arch/arm/include/asm/module.h +++ b/arch/arm/include/asm/module.h @@ -7,20 +7,27 @@ struct unwind_table; -struct mod_arch_specific -{ #ifdef CONFIG_ARM_UNWIND - Elf_Shdr *unw_sec_init; - Elf_Shdr *unw_sec_devinit; - Elf_Shdr *unw_sec_core; - Elf_Shdr *sec_init_text; - Elf_Shdr *sec_devinit_text; - Elf_Shdr *sec_core_text; - struct unwind_table *unwind_init; - struct unwind_table *unwind_devinit; - struct unwind_table *unwind_core; -#endif +struct arm_unwind_mapping { + Elf_Shdr *unw_sec; + Elf_Shdr *sec_text; + struct unwind_table *unwind; +}; +enum { + ARM_SEC_INIT, + ARM_SEC_DEVINIT, + ARM_SEC_CORE, + ARM_SEC_EXIT, + ARM_SEC_DEVEXIT, + ARM_SEC_MAX, +}; +struct mod_arch_specific { + struct arm_unwind_mapping map[ARM_SEC_MAX]; }; +#else +struct mod_arch_specific { +}; +#endif /* * Include the ARM architecture version. diff --git a/arch/arm/include/asm/pgtable.h b/arch/arm/include/asm/pgtable.h index e90b167ea84840..a9672e8406a3cd 100644 --- a/arch/arm/include/asm/pgtable.h +++ b/arch/arm/include/asm/pgtable.h @@ -278,9 +278,24 @@ extern struct page *empty_zero_page; #define set_pte_ext(ptep,pte,ext) cpu_set_pte_ext(ptep,pte,ext) -#define set_pte_at(mm,addr,ptep,pteval) do { \ - set_pte_ext(ptep, pteval, (addr) >= TASK_SIZE ? 0 : PTE_EXT_NG); \ - } while (0) +#if __LINUX_ARM_ARCH__ < 6 +static inline void __sync_icache_dcache(pte_t pteval) +{ +} +#else +extern void __sync_icache_dcache(pte_t pteval); +#endif + +static inline void set_pte_at(struct mm_struct *mm, unsigned long addr, + pte_t *ptep, pte_t pteval) +{ + if (addr >= TASK_SIZE) + set_pte_ext(ptep, pteval, 0); + else { + __sync_icache_dcache(pteval); + set_pte_ext(ptep, pteval, PTE_EXT_NG); + } +} /* * The following only work if pte_present() is true. @@ -290,8 +305,13 @@ extern struct page *empty_zero_page; #define pte_write(pte) (pte_val(pte) & L_PTE_WRITE) #define pte_dirty(pte) (pte_val(pte) & L_PTE_DIRTY) #define pte_young(pte) (pte_val(pte) & L_PTE_YOUNG) +#define pte_exec(pte) (pte_val(pte) & L_PTE_EXEC) #define pte_special(pte) (0) +#define pte_present_user(pte) \ + ((pte_val(pte) & (L_PTE_PRESENT | L_PTE_USER)) == \ + (L_PTE_PRESENT | L_PTE_USER)) + #define PTE_BIT_FUNC(fn,op) \ static inline pte_t pte_##fn(pte_t pte) { pte_val(pte) op; return pte; } diff --git a/arch/arm/include/asm/processor.h b/arch/arm/include/asm/processor.h index 7bed3daf83b8f2..67357baaeeebd9 100644 --- a/arch/arm/include/asm/processor.h +++ b/arch/arm/include/asm/processor.h @@ -19,6 +19,7 @@ #ifdef __KERNEL__ +#include #include #include @@ -41,6 +42,9 @@ struct debug_entry { struct debug_info { int nsaved; struct debug_entry bp[2]; +#ifdef CONFIG_HAVE_HW_BREAKPOINT + struct perf_event *hbp[ARM_MAX_HBP_SLOTS]; +#endif }; struct thread_struct { diff --git a/arch/arm/include/asm/ptrace.h b/arch/arm/include/asm/ptrace.h index 7ce15eb15f7299..783d50f326181c 100644 --- a/arch/arm/include/asm/ptrace.h +++ b/arch/arm/include/asm/ptrace.h @@ -29,6 +29,8 @@ #define PTRACE_SETCRUNCHREGS 26 #define PTRACE_GETVFPREGS 27 #define PTRACE_SETVFPREGS 28 +#define PTRACE_GETHBPREGS 29 +#define PTRACE_SETHBPREGS 30 /* * PSR bits diff --git a/arch/arm/include/asm/seccomp.h b/arch/arm/include/asm/seccomp.h new file mode 100644 index 00000000000000..52b156b341f519 --- /dev/null +++ b/arch/arm/include/asm/seccomp.h @@ -0,0 +1,11 @@ +#ifndef _ASM_ARM_SECCOMP_H +#define _ASM_ARM_SECCOMP_H + +#include + +#define __NR_seccomp_read __NR_read +#define __NR_seccomp_write __NR_write +#define __NR_seccomp_exit __NR_exit +#define __NR_seccomp_sigreturn __NR_rt_sigreturn + +#endif /* _ASM_ARM_SECCOMP_H */ diff --git a/arch/arm/include/asm/smp_mpidr.h b/arch/arm/include/asm/smp_mpidr.h new file mode 100644 index 00000000000000..6a9307d6490034 --- /dev/null +++ b/arch/arm/include/asm/smp_mpidr.h @@ -0,0 +1,17 @@ +#ifndef ASMARM_SMP_MIDR_H +#define ASMARM_SMP_MIDR_H + +#define hard_smp_processor_id() \ + ({ \ + unsigned int cpunum; \ + __asm__("\n" \ + "1: mrc p15, 0, %0, c0, c0, 5\n" \ + " .pushsection \".alt.smp.init\", \"a\"\n"\ + " .long 1b\n" \ + " mov %0, #0\n" \ + " .popsection" \ + : "=r" (cpunum)); \ + cpunum &= 0x0F; \ + }) + +#endif diff --git a/arch/arm/include/asm/smp_plat.h b/arch/arm/include/asm/smp_plat.h index e6215305544aa9..f24c1b9e211dd1 100644 --- a/arch/arm/include/asm/smp_plat.h +++ b/arch/arm/include/asm/smp_plat.h @@ -7,15 +7,40 @@ #include +/* + * Return true if we are running on a SMP platform + */ +static inline bool is_smp(void) +{ +#ifndef CONFIG_SMP + return false; +#elif defined(CONFIG_SMP_ON_UP) + extern unsigned int smp_on_up; + return !!smp_on_up; +#else + return true; +#endif +} + /* all SMP configurations have the extended CPUID registers */ static inline int tlb_ops_need_broadcast(void) { + if (!is_smp()) + return 0; + return ((read_cpuid_ext(CPUID_EXT_MMFR3) >> 12) & 0xf) < 2; } +#if !defined(CONFIG_SMP) || __LINUX_ARM_ARCH__ >= 7 +#define cache_ops_need_broadcast() 0 +#else static inline int cache_ops_need_broadcast(void) { + if (!is_smp()) + return 0; + return ((read_cpuid_ext(CPUID_EXT_MMFR3) >> 12) & 0xf) < 1; } +#endif #endif diff --git a/arch/arm/include/asm/system.h b/arch/arm/include/asm/system.h index 8ba1ccf82a0200..1120f18a6b1769 100644 --- a/arch/arm/include/asm/system.h +++ b/arch/arm/include/asm/system.h @@ -85,6 +85,10 @@ void hook_fault_code(int nr, int (*fn)(unsigned long, unsigned int, struct pt_regs *), int sig, int code, const char *name); +void hook_ifault_code(int nr, int (*fn)(unsigned long, unsigned int, + struct pt_regs *), + int sig, int code, const char *name); + #define xchg(ptr,x) \ ((__typeof__(*(ptr)))__xchg((unsigned long)(x),(ptr),sizeof(*(ptr)))) @@ -325,6 +329,8 @@ static inline unsigned long __xchg(unsigned long x, volatile void *ptr, int size extern void disable_hlt(void); extern void enable_hlt(void); +void cpu_idle_wait(void); + #include #if __LINUX_ARM_ARCH__ < 6 diff --git a/arch/arm/include/asm/thread_info.h b/arch/arm/include/asm/thread_info.h index 763e29fa85300b..7b5cc8dae06e6e 100644 --- a/arch/arm/include/asm/thread_info.h +++ b/arch/arm/include/asm/thread_info.h @@ -144,6 +144,7 @@ extern void vfp_flush_hwstate(struct thread_info *); #define TIF_MEMDIE 18 /* is terminating due to OOM killer */ #define TIF_FREEZE 19 #define TIF_RESTORE_SIGMASK 20 +#define TIF_SECCOMP 21 #define _TIF_SIGPENDING (1 << TIF_SIGPENDING) #define _TIF_NEED_RESCHED (1 << TIF_NEED_RESCHED) @@ -153,6 +154,7 @@ extern void vfp_flush_hwstate(struct thread_info *); #define _TIF_USING_IWMMXT (1 << TIF_USING_IWMMXT) #define _TIF_FREEZE (1 << TIF_FREEZE) #define _TIF_RESTORE_SIGMASK (1 << TIF_RESTORE_SIGMASK) +#define _TIF_SECCOMP (1 << TIF_SECCOMP) /* * Change these and you break ASM code in entry-common.S diff --git a/arch/arm/include/asm/tlbflush.h b/arch/arm/include/asm/tlbflush.h index 33b546ae72d49c..ce7378ea15a2b3 100644 --- a/arch/arm/include/asm/tlbflush.h +++ b/arch/arm/include/asm/tlbflush.h @@ -70,6 +70,10 @@ #undef _TLB #undef MULTI_TLB +#ifdef CONFIG_SMP_ON_UP +#define MULTI_TLB 1 +#endif + #define v3_tlb_flags (TLB_V3_FULL | TLB_V3_PAGE) #ifdef CONFIG_CPU_TLB_V3 @@ -185,17 +189,23 @@ # define v6wbi_always_flags (-1UL) #endif -#ifdef CONFIG_SMP -#define v7wbi_tlb_flags (TLB_WB | TLB_DCLEAN | TLB_V7_IS_BTB | \ +#define v7wbi_tlb_flags_smp (TLB_WB | TLB_DCLEAN | TLB_V7_IS_BTB | \ TLB_V7_UIS_FULL | TLB_V7_UIS_PAGE | TLB_V7_UIS_ASID) -#else -#define v7wbi_tlb_flags (TLB_WB | TLB_DCLEAN | TLB_BTB | \ +#define v7wbi_tlb_flags_up (TLB_WB | TLB_DCLEAN | TLB_BTB | \ TLB_V6_U_FULL | TLB_V6_U_PAGE | TLB_V6_U_ASID) -#endif #ifdef CONFIG_CPU_TLB_V7 -# define v7wbi_possible_flags v7wbi_tlb_flags -# define v7wbi_always_flags v7wbi_tlb_flags + +# ifdef CONFIG_SMP_ON_UP +# define v7wbi_possible_flags (v7wbi_tlb_flags_smp | v7wbi_tlb_flags_up) +# define v7wbi_always_flags (v7wbi_tlb_flags_smp & v7wbi_tlb_flags_up) +# elif defined(CONFIG_SMP) +# define v7wbi_possible_flags v7wbi_tlb_flags_smp +# define v7wbi_always_flags v7wbi_tlb_flags_smp +# else +# define v7wbi_possible_flags v7wbi_tlb_flags_up +# define v7wbi_always_flags v7wbi_tlb_flags_up +# endif # ifdef _TLB # define MULTI_TLB 1 # else @@ -560,12 +570,20 @@ extern void flush_tlb_kernel_range(unsigned long start, unsigned long end); #endif /* - * if PG_dcache_dirty is set for the page, we need to ensure that any + * If PG_dcache_clean is not set for the page, we need to ensure that any * cache entries for the kernels virtual memory range are written - * back to the page. + * back to the page. On ARMv6 and later, the cache coherency is handled via + * the set_pte_at() function. */ +#if __LINUX_ARM_ARCH__ < 6 extern void update_mmu_cache(struct vm_area_struct *vma, unsigned long addr, pte_t *ptep); +#else +static inline void update_mmu_cache(struct vm_area_struct *vma, + unsigned long addr, pte_t *ptep) +{ +} +#endif #endif diff --git a/arch/arm/kernel/Makefile b/arch/arm/kernel/Makefile index 980b78e3132815..5b9b268f4fbb36 100644 --- a/arch/arm/kernel/Makefile +++ b/arch/arm/kernel/Makefile @@ -42,6 +42,7 @@ obj-$(CONFIG_KGDB) += kgdb.o obj-$(CONFIG_ARM_UNWIND) += unwind.o obj-$(CONFIG_HAVE_TCM) += tcm.o obj-$(CONFIG_CRASH_DUMP) += crash_dump.o +obj-$(CONFIG_HAVE_HW_BREAKPOINT) += hw_breakpoint.o obj-$(CONFIG_CRUNCH) += crunch.o crunch-bits.o AFLAGS_crunch-bits.o := -Wa,-mcpu=ep9312 diff --git a/arch/arm/kernel/armksyms.c b/arch/arm/kernel/armksyms.c index 8214bfebfaca66..e5e1e5387678f7 100644 --- a/arch/arm/kernel/armksyms.c +++ b/arch/arm/kernel/armksyms.c @@ -165,6 +165,8 @@ EXPORT_SYMBOL(_find_next_bit_be); #endif #ifdef CONFIG_FUNCTION_TRACER +#ifdef CONFIG_OLD_MCOUNT EXPORT_SYMBOL(mcount); +#endif EXPORT_SYMBOL(__gnu_mcount_nc); #endif diff --git a/arch/arm/kernel/asm-offsets.c b/arch/arm/kernel/asm-offsets.c index 85f2a019f77bc9..82da661721327c 100644 --- a/arch/arm/kernel/asm-offsets.c +++ b/arch/arm/kernel/asm-offsets.c @@ -102,8 +102,6 @@ int main(void) DEFINE(SIZEOF_MACHINE_DESC, sizeof(struct machine_desc)); DEFINE(MACHINFO_TYPE, offsetof(struct machine_desc, nr)); DEFINE(MACHINFO_NAME, offsetof(struct machine_desc, name)); - DEFINE(MACHINFO_PHYSIO, offsetof(struct machine_desc, phys_io)); - DEFINE(MACHINFO_PGOFFIO, offsetof(struct machine_desc, io_pg_offst)); BLANK(); DEFINE(PROC_INFO_SZ, sizeof(struct proc_info_list)); DEFINE(PROCINFO_INITFUNC, offsetof(struct proc_info_list, __cpu_flush)); diff --git a/arch/arm/kernel/debug.S b/arch/arm/kernel/debug.S index a38b4879441d17..a0f07521ca8a2d 100644 --- a/arch/arm/kernel/debug.S +++ b/arch/arm/kernel/debug.S @@ -22,11 +22,11 @@ #if defined(CONFIG_DEBUG_ICEDCC) @@ debug using ARM EmbeddedICE DCC channel -#if defined(CONFIG_CPU_V6) - - .macro addruart, rx, tmp + .macro addruart, rp, rv .endm +#if defined(CONFIG_CPU_V6) + .macro senduart, rd, rx mcr p14, 0, \rd, c0, c5, 0 .endm @@ -51,9 +51,6 @@ #elif defined(CONFIG_CPU_V7) - .macro addruart, rx, tmp - .endm - .macro senduart, rd, rx mcr p14, 0, \rd, c0, c5, 0 .endm @@ -71,9 +68,6 @@ wait: mrc p14, 0, pc, c0, c1, 0 #elif defined(CONFIG_CPU_XSCALE) - .macro addruart, rx, tmp - .endm - .macro senduart, rd, rx mcr p14, 0, \rd, c8, c0, 0 .endm @@ -98,9 +92,6 @@ wait: mrc p14, 0, pc, c0, c1, 0 #else - .macro addruart, rx, tmp - .endm - .macro senduart, rd, rx mcr p14, 0, \rd, c1, c0, 0 .endm @@ -130,6 +121,22 @@ wait: mrc p14, 0, pc, c0, c1, 0 #include #endif /* CONFIG_DEBUG_ICEDCC */ +#ifdef CONFIG_MMU + .macro addruart_current, rx, tmp1, tmp2 + addruart \tmp1, \tmp2 + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 + moveq \rx, \tmp1 + movne \rx, \tmp2 + .endm + +#else /* !CONFIG_MMU */ + .macro addruart_current, rx, tmp1, tmp2 + addruart \rx, \tmp1 + .endm + +#endif /* CONFIG_MMU */ + /* * Useful debugging routines */ @@ -164,7 +171,7 @@ ENDPROC(printhex2) .ltorg ENTRY(printascii) - addruart r3, r1 + addruart_current r3, r1, r2 b 2f 1: waituart r2, r3 senduart r1, r3 @@ -180,7 +187,7 @@ ENTRY(printascii) ENDPROC(printascii) ENTRY(printch) - addruart r3, r1 + addruart_current r3, r1, r2 mov r1, r0 mov r0, #0 b 1b diff --git a/arch/arm/kernel/entry-armv.S b/arch/arm/kernel/entry-armv.S index bb8e93a7640724..c09e3573c5deb5 100644 --- a/arch/arm/kernel/entry-armv.S +++ b/arch/arm/kernel/entry-armv.S @@ -46,7 +46,8 @@ * this macro assumes that irqstat (r6) and base (r5) are * preserved from get_irqnr_and_base above */ - test_for_ipi r0, r6, r5, lr + ALT_SMP(test_for_ipi r0, r6, r5, lr) + ALT_UP_B(9997f) movne r0, sp adrne lr, BSYM(1b) bne do_IPI @@ -57,6 +58,7 @@ adrne lr, BSYM(1b) bne do_local_timer #endif +9997: #endif .endm @@ -965,11 +967,8 @@ kuser_cmpxchg_fixup: beq 1b rsbs r0, r3, #0 /* beware -- each __kuser slot must be 8 instructions max */ -#ifdef CONFIG_SMP - b __kuser_memory_barrier -#else - usr_ret lr -#endif + ALT_SMP(b __kuser_memory_barrier) + ALT_UP(usr_ret lr) #endif diff --git a/arch/arm/kernel/entry-common.S b/arch/arm/kernel/entry-common.S index 7885722bdf4eff..8bfa98757cd2f3 100644 --- a/arch/arm/kernel/entry-common.S +++ b/arch/arm/kernel/entry-common.S @@ -129,30 +129,58 @@ ENDPROC(ret_from_fork) * clobber the ip register. This is OK because the ARM calling convention * allows it to be clobbered in subroutines and doesn't use it to hold * parameters.) + * + * When using dynamic ftrace, we patch out the mcount call by a "mov r0, r0" + * for the mcount case, and a "pop {lr}" for the __gnu_mcount_nc case (see + * arch/arm/kernel/ftrace.c). */ + +#ifndef CONFIG_OLD_MCOUNT +#if (__GNUC__ < 4 || (__GNUC__ == 4 && __GNUC_MINOR__ < 4)) +#error Ftrace requires CONFIG_FRAME_POINTER=y with GCC older than 4.4.0. +#endif +#endif + #ifdef CONFIG_DYNAMIC_FTRACE -ENTRY(mcount) +ENTRY(__gnu_mcount_nc) + mov ip, lr + ldmia sp!, {lr} + mov pc, ip +ENDPROC(__gnu_mcount_nc) + +ENTRY(ftrace_caller) stmdb sp!, {r0-r3, lr} mov r0, lr sub r0, r0, #MCOUNT_INSN_SIZE + ldr r1, [sp, #20] - .globl mcount_call -mcount_call: + .global ftrace_call +ftrace_call: bl ftrace_stub - ldr lr, [fp, #-4] @ restore lr - ldmia sp!, {r0-r3, pc} + ldmia sp!, {r0-r3, ip, lr} + mov pc, ip +ENDPROC(ftrace_caller) -ENTRY(ftrace_caller) +#ifdef CONFIG_OLD_MCOUNT +ENTRY(mcount) + stmdb sp!, {lr} + ldr lr, [fp, #-4] + ldmia sp!, {pc} +ENDPROC(mcount) + +ENTRY(ftrace_caller_old) stmdb sp!, {r0-r3, lr} ldr r1, [fp, #-4] mov r0, lr sub r0, r0, #MCOUNT_INSN_SIZE - .globl ftrace_call -ftrace_call: + .globl ftrace_call_old +ftrace_call_old: bl ftrace_stub ldr lr, [fp, #-4] @ restore lr ldmia sp!, {r0-r3, pc} +ENDPROC(ftrace_caller_old) +#endif #else @@ -160,7 +188,7 @@ ENTRY(__gnu_mcount_nc) stmdb sp!, {r0-r3, lr} ldr r0, =ftrace_trace_function ldr r2, [r0] - adr r0, ftrace_stub + adr r0, .Lftrace_stub cmp r0, r2 bne gnu_trace ldmia sp!, {r0-r3, ip, lr} @@ -170,11 +198,19 @@ gnu_trace: ldr r1, [sp, #20] @ lr of instrumented routine mov r0, lr sub r0, r0, #MCOUNT_INSN_SIZE - mov lr, pc + adr lr, BSYM(1f) mov pc, r2 +1: ldmia sp!, {r0-r3, ip, lr} mov pc, ip +ENDPROC(__gnu_mcount_nc) +#ifdef CONFIG_OLD_MCOUNT +/* + * This is under an ifdef in order to force link-time errors for people trying + * to build with !FRAME_POINTER with a GCC which doesn't use the new-style + * mcount. + */ ENTRY(mcount) stmdb sp!, {r0-r3, lr} ldr r0, =ftrace_trace_function @@ -193,12 +229,15 @@ trace: mov pc, r2 ldr lr, [fp, #-4] @ restore lr ldmia sp!, {r0-r3, pc} +ENDPROC(mcount) +#endif #endif /* CONFIG_DYNAMIC_FTRACE */ - .globl ftrace_stub -ftrace_stub: +ENTRY(ftrace_stub) +.Lftrace_stub: mov pc, lr +ENDPROC(ftrace_stub) #endif /* CONFIG_FUNCTION_TRACER */ @@ -295,7 +334,6 @@ ENTRY(vector_swi) get_thread_info tsk adr tbl, sys_call_table @ load syscall table pointer - ldr ip, [tsk, #TI_FLAGS] @ check for syscall tracing #if defined(CONFIG_OABI_COMPAT) /* @@ -312,8 +350,20 @@ ENTRY(vector_swi) eor scno, scno, #__NR_SYSCALL_BASE @ check OS number #endif + ldr r10, [tsk, #TI_FLAGS] @ check for syscall tracing stmdb sp!, {r4, r5} @ push fifth and sixth args - tst ip, #_TIF_SYSCALL_TRACE @ are we tracing syscalls? + +#ifdef CONFIG_SECCOMP + tst r10, #_TIF_SECCOMP + beq 1f + mov r0, scno + bl __secure_computing + add r0, sp, #S_R0 + S_OFF @ pointer to regs + ldmia r0, {r0 - r3} @ have to reload r0 - r3 +1: +#endif + + tst r10, #_TIF_SYSCALL_TRACE @ are we tracing syscalls? bne __sys_trace cmp scno, #NR_syscalls @ check upper syscall limit diff --git a/arch/arm/kernel/etm.c b/arch/arm/kernel/etm.c index 33c7077174db11..a48d512579880f 100644 --- a/arch/arm/kernel/etm.c +++ b/arch/arm/kernel/etm.c @@ -30,6 +30,21 @@ MODULE_LICENSE("GPL"); MODULE_AUTHOR("Alexander Shishkin"); +/* + * ETM tracer state + */ +struct tracectx { + unsigned int etb_bufsz; + void __iomem *etb_regs; + void __iomem *etm_regs; + unsigned long flags; + int ncmppairs; + int etm_portsz; + struct device *dev; + struct clk *emu_clk; + struct mutex mutex; +}; + static struct tracectx tracer; static inline bool trace_isrunning(struct tracectx *t) diff --git a/arch/arm/kernel/ftrace.c b/arch/arm/kernel/ftrace.c index 0298286ad4ad59..971ac8c36ea775 100644 --- a/arch/arm/kernel/ftrace.c +++ b/arch/arm/kernel/ftrace.c @@ -2,102 +2,194 @@ * Dynamic function tracing support. * * Copyright (C) 2008 Abhishek Sagar + * Copyright (C) 2010 Rabin Vincent * * For licencing details, see COPYING. * * Defines low-level handling of mcount calls when the kernel * is compiled with the -pg flag. When using dynamic ftrace, the - * mcount call-sites get patched lazily with NOP till they are - * enabled. All code mutation routines here take effect atomically. + * mcount call-sites get patched with NOP till they are enabled. + * All code mutation routines here are called under stop_machine(). */ #include +#include #include #include -#define PC_OFFSET 8 -#define BL_OPCODE 0xeb000000 -#define BL_OFFSET_MASK 0x00ffffff +#ifdef CONFIG_THUMB2_KERNEL +#define NOP 0xeb04f85d /* pop.w {lr} */ +#else +#define NOP 0xe8bd4000 /* pop {lr} */ +#endif -static unsigned long bl_insn; -static const unsigned long NOP = 0xe1a00000; /* mov r0, r0 */ +#ifdef CONFIG_OLD_MCOUNT +#define OLD_MCOUNT_ADDR ((unsigned long) mcount) +#define OLD_FTRACE_ADDR ((unsigned long) ftrace_caller_old) -unsigned char *ftrace_nop_replace(void) +#define OLD_NOP 0xe1a00000 /* mov r0, r0 */ + +static unsigned long ftrace_nop_replace(struct dyn_ftrace *rec) { - return (char *)&NOP; + return rec->arch.old_mcount ? OLD_NOP : NOP; } +static unsigned long adjust_address(struct dyn_ftrace *rec, unsigned long addr) +{ + if (!rec->arch.old_mcount) + return addr; + + if (addr == MCOUNT_ADDR) + addr = OLD_MCOUNT_ADDR; + else if (addr == FTRACE_ADDR) + addr = OLD_FTRACE_ADDR; + + return addr; +} +#else +static unsigned long ftrace_nop_replace(struct dyn_ftrace *rec) +{ + return NOP; +} + +static unsigned long adjust_address(struct dyn_ftrace *rec, unsigned long addr) +{ + return addr; +} +#endif + /* construct a branch (BL) instruction to addr */ -unsigned char *ftrace_call_replace(unsigned long pc, unsigned long addr) +#ifdef CONFIG_THUMB2_KERNEL +static unsigned long ftrace_call_replace(unsigned long pc, unsigned long addr) { + unsigned long s, j1, j2, i1, i2, imm10, imm11; + unsigned long first, second; long offset; - offset = (long)addr - (long)(pc + PC_OFFSET); + offset = (long)addr - (long)(pc + 4); + if (offset < -16777216 || offset > 16777214) { + WARN_ON_ONCE(1); + return 0; + } + + s = (offset >> 24) & 0x1; + i1 = (offset >> 23) & 0x1; + i2 = (offset >> 22) & 0x1; + imm10 = (offset >> 12) & 0x3ff; + imm11 = (offset >> 1) & 0x7ff; + + j1 = (!i1) ^ s; + j2 = (!i2) ^ s; + + first = 0xf000 | (s << 10) | imm10; + second = 0xd000 | (j1 << 13) | (j2 << 11) | imm11; + + return (second << 16) | first; +} +#else +static unsigned long ftrace_call_replace(unsigned long pc, unsigned long addr) +{ + long offset; + + offset = (long)addr - (long)(pc + 8); if (unlikely(offset < -33554432 || offset > 33554428)) { /* Can't generate branches that far (from ARM ARM). Ftrace * doesn't generate branches outside of kernel text. */ WARN_ON_ONCE(1); - return NULL; + return 0; } - offset = (offset >> 2) & BL_OFFSET_MASK; - bl_insn = BL_OPCODE | offset; - return (unsigned char *)&bl_insn; -} -int ftrace_modify_code(unsigned long pc, unsigned char *old_code, - unsigned char *new_code) -{ - unsigned long err = 0, replaced = 0, old, new; + offset = (offset >> 2) & 0x00ffffff; - old = *(unsigned long *)old_code; - new = *(unsigned long *)new_code; + return 0xeb000000 | offset; +} +#endif - __asm__ __volatile__ ( - "1: ldr %1, [%2] \n" - " cmp %1, %4 \n" - "2: streq %3, [%2] \n" - " cmpne %1, %3 \n" - " movne %0, #2 \n" - "3:\n" +static int ftrace_modify_code(unsigned long pc, unsigned long old, + unsigned long new) +{ + unsigned long replaced; - ".pushsection .fixup, \"ax\"\n" - "4: mov %0, #1 \n" - " b 3b \n" - ".popsection\n" + if (probe_kernel_read(&replaced, (void *)pc, MCOUNT_INSN_SIZE)) + return -EFAULT; - ".pushsection __ex_table, \"a\"\n" - " .long 1b, 4b \n" - " .long 2b, 4b \n" - ".popsection\n" + if (replaced != old) + return -EINVAL; - : "=r"(err), "=r"(replaced) - : "r"(pc), "r"(new), "r"(old), "0"(err), "1"(replaced) - : "memory"); + if (probe_kernel_write((void *)pc, &new, MCOUNT_INSN_SIZE)) + return -EPERM; - if (!err && (replaced == old)) - flush_icache_range(pc, pc + MCOUNT_INSN_SIZE); + flush_icache_range(pc, pc + MCOUNT_INSN_SIZE); - return err; + return 0; } int ftrace_update_ftrace_func(ftrace_func_t func) { - int ret; unsigned long pc, old; - unsigned char *new; + unsigned long new; + int ret; pc = (unsigned long)&ftrace_call; memcpy(&old, &ftrace_call, MCOUNT_INSN_SIZE); new = ftrace_call_replace(pc, (unsigned long)func); - ret = ftrace_modify_code(pc, (unsigned char *)&old, new); + + ret = ftrace_modify_code(pc, old, new); + +#ifdef CONFIG_OLD_MCOUNT + if (!ret) { + pc = (unsigned long)&ftrace_call_old; + memcpy(&old, &ftrace_call_old, MCOUNT_INSN_SIZE); + new = ftrace_call_replace(pc, (unsigned long)func); + + ret = ftrace_modify_code(pc, old, new); + } +#endif + + return ret; +} + +int ftrace_make_call(struct dyn_ftrace *rec, unsigned long addr) +{ + unsigned long new, old; + unsigned long ip = rec->ip; + + old = ftrace_nop_replace(rec); + new = ftrace_call_replace(ip, adjust_address(rec, addr)); + + return ftrace_modify_code(rec->ip, old, new); +} + +int ftrace_make_nop(struct module *mod, + struct dyn_ftrace *rec, unsigned long addr) +{ + unsigned long ip = rec->ip; + unsigned long old; + unsigned long new; + int ret; + + old = ftrace_call_replace(ip, adjust_address(rec, addr)); + new = ftrace_nop_replace(rec); + ret = ftrace_modify_code(ip, old, new); + +#ifdef CONFIG_OLD_MCOUNT + if (ret == -EINVAL && addr == MCOUNT_ADDR) { + rec->arch.old_mcount = true; + + old = ftrace_call_replace(ip, adjust_address(rec, addr)); + new = ftrace_nop_replace(rec); + ret = ftrace_modify_code(ip, old, new); + } +#endif + return ret; } -/* run from ftrace_init with irqs disabled */ int __init ftrace_dyn_arch_init(void *data) { - ftrace_mcount_set(data); + *(unsigned long *)data = 0; + return 0; } diff --git a/arch/arm/kernel/head-common.S b/arch/arm/kernel/head-common.S index b9505aa267c003..bbecaac1e01351 100644 --- a/arch/arm/kernel/head-common.S +++ b/arch/arm/kernel/head-common.S @@ -15,55 +15,6 @@ #define ATAG_CORE_SIZE ((2*4 + 3*4) >> 2) #define ATAG_CORE_SIZE_EMPTY ((2*4) >> 2) - .align 2 - .type __switch_data, %object -__switch_data: - .long __mmap_switched - .long __data_loc @ r4 - .long _data @ r5 - .long __bss_start @ r6 - .long _end @ r7 - .long processor_id @ r4 - .long __machine_arch_type @ r5 - .long __atags_pointer @ r6 - .long cr_alignment @ r7 - .long init_thread_union + THREAD_START_SP @ sp - -/* - * The following fragment of code is executed with the MMU on in MMU mode, - * and uses absolute addresses; this is not position independent. - * - * r0 = cp#15 control register - * r1 = machine ID - * r2 = atags pointer - * r9 = processor ID - */ -__mmap_switched: - adr r3, __switch_data + 4 - - ldmia r3!, {r4, r5, r6, r7} - cmp r4, r5 @ Copy data segment if needed -1: cmpne r5, r6 - ldrne fp, [r4], #4 - strne fp, [r5], #4 - bne 1b - - mov fp, #0 @ Clear BSS (and zero fp) -1: cmp r6, r7 - strcc fp, [r6],#4 - bcc 1b - - ARM( ldmia r3, {r4, r5, r6, r7, sp}) - THUMB( ldmia r3, {r4, r5, r6, r7} ) - THUMB( ldr sp, [r3, #16] ) - str r9, [r4] @ Save processor ID - str r1, [r5] @ Save machine type - str r2, [r6] @ Save atags pointer - bic r4, r0, #CR_A @ Clear 'A' bit - stmia r7, {r0, r4} @ Save control register values - b start_kernel -ENDPROC(__mmap_switched) - /* * Exception handling. Something went wrong and we can't proceed. We * ought to tell the user, but since we don't have any guarantee that @@ -73,21 +24,7 @@ ENDPROC(__mmap_switched) * and hope for the best (useful if bootloader fails to pass a proper * machine ID for example). */ -__error_p: -#ifdef CONFIG_DEBUG_LL - adr r0, str_p1 - bl printascii - mov r0, r9 - bl printhex8 - adr r0, str_p2 - bl printascii - b __error -str_p1: .asciz "\nError: unrecognized/unsupported processor variant (0x" -str_p2: .asciz ").\n" - .align -#endif -ENDPROC(__error_p) - + __HEAD __error_a: #ifdef CONFIG_DEBUG_LL mov r4, r1 @ preserve machine ID @@ -97,7 +34,7 @@ __error_a: bl printhex8 adr r0, str_a2 bl printascii - adr r3, 4f + adr r3, __lookup_machine_type_data ldmia r3, {r4, r5, r6} @ get machine desc list sub r4, r3, r4 @ get offset between virt&phys add r5, r5, r4 @ convert virt addresses to @@ -125,78 +62,6 @@ str_a3: .asciz "\nPlease check your kernel config and/or bootloader.\n" .align #endif -__error: -#ifdef CONFIG_ARCH_RPC -/* - * Turn the screen red on a error - RiscPC only. - */ - mov r0, #0x02000000 - mov r3, #0x11 - orr r3, r3, r3, lsl #8 - orr r3, r3, r3, lsl #16 - str r3, [r0], #4 - str r3, [r0], #4 - str r3, [r0], #4 - str r3, [r0], #4 -#endif -1: mov r0, r0 - b 1b -ENDPROC(__error) - - -/* - * Read processor ID register (CP#15, CR0), and look up in the linker-built - * supported processor list. Note that we can't use the absolute addresses - * for the __proc_info lists since we aren't running with the MMU on - * (and therefore, we are not in the correct address space). We have to - * calculate the offset. - * - * r9 = cpuid - * Returns: - * r3, r4, r6 corrupted - * r5 = proc_info pointer in physical address space - * r9 = cpuid (preserved) - */ -__lookup_processor_type: - adr r3, 3f - ldmia r3, {r5 - r7} - add r3, r3, #8 - sub r3, r3, r7 @ get offset between virt&phys - add r5, r5, r3 @ convert virt addresses to - add r6, r6, r3 @ physical address space -1: ldmia r5, {r3, r4} @ value, mask - and r4, r4, r9 @ mask wanted bits - teq r3, r4 - beq 2f - add r5, r5, #PROC_INFO_SZ @ sizeof(proc_info_list) - cmp r5, r6 - blo 1b - mov r5, #0 @ unknown processor -2: mov pc, lr -ENDPROC(__lookup_processor_type) - -/* - * This provides a C-API version of the above function. - */ -ENTRY(lookup_processor_type) - stmfd sp!, {r4 - r7, r9, lr} - mov r9, r0 - bl __lookup_processor_type - mov r0, r5 - ldmfd sp!, {r4 - r7, r9, pc} -ENDPROC(lookup_processor_type) - -/* - * Look in and arch/arm/kernel/arch.[ch] for - * more information about the __proc_info and __arch_info structures. - */ - .align 2 -3: .long __proc_info_begin - .long __proc_info_end -4: .long . - .long __arch_info_begin - .long __arch_info_end - /* * Lookup machine architecture in the linker-build list of architectures. * Note that we can't use the absolute addresses for the __arch_info @@ -209,7 +74,7 @@ ENDPROC(lookup_processor_type) * r5 = mach_info pointer in physical address space */ __lookup_machine_type: - adr r3, 4b + adr r3, __lookup_machine_type_data ldmia r3, {r4, r5, r6} sub r3, r3, r4 @ get offset between virt&phys add r5, r5, r3 @ convert virt addresses to @@ -225,15 +90,16 @@ __lookup_machine_type: ENDPROC(__lookup_machine_type) /* - * This provides a C-API version of the above function. + * Look in arch/arm/kernel/arch.[ch] for information about the + * __arch_info structures. */ -ENTRY(lookup_machine_type) - stmfd sp!, {r4 - r6, lr} - mov r1, r0 - bl __lookup_machine_type - mov r0, r5 - ldmfd sp!, {r4 - r6, pc} -ENDPROC(lookup_machine_type) + .align 2 + .type __lookup_machine_type_data, %object +__lookup_machine_type_data: + .long . + .long __arch_info_begin + .long __arch_info_end + .size __lookup_machine_type_data, . - __lookup_machine_type_data /* Determine validity of the r2 atags pointer. The heuristic requires * that the pointer be aligned, in the first 16k of physical RAM and @@ -265,3 +131,150 @@ __vet_atags: 1: mov r2, #0 mov pc, lr ENDPROC(__vet_atags) + +/* + * The following fragment of code is executed with the MMU on in MMU mode, + * and uses absolute addresses; this is not position independent. + * + * r0 = cp#15 control register + * r1 = machine ID + * r2 = atags pointer + * r9 = processor ID + */ + __INIT +__mmap_switched: + adr r3, __mmap_switched_data + + ldmia r3!, {r4, r5, r6, r7} + cmp r4, r5 @ Copy data segment if needed +1: cmpne r5, r6 + ldrne fp, [r4], #4 + strne fp, [r5], #4 + bne 1b + + mov fp, #0 @ Clear BSS (and zero fp) +1: cmp r6, r7 + strcc fp, [r6],#4 + bcc 1b + + ARM( ldmia r3, {r4, r5, r6, r7, sp}) + THUMB( ldmia r3, {r4, r5, r6, r7} ) + THUMB( ldr sp, [r3, #16] ) + str r9, [r4] @ Save processor ID + str r1, [r5] @ Save machine type + str r2, [r6] @ Save atags pointer + bic r4, r0, #CR_A @ Clear 'A' bit + stmia r7, {r0, r4} @ Save control register values + b start_kernel +ENDPROC(__mmap_switched) + + .align 2 + .type __mmap_switched_data, %object +__mmap_switched_data: + .long __data_loc @ r4 + .long _sdata @ r5 + .long __bss_start @ r6 + .long _end @ r7 + .long processor_id @ r4 + .long __machine_arch_type @ r5 + .long __atags_pointer @ r6 + .long cr_alignment @ r7 + .long init_thread_union + THREAD_START_SP @ sp + .size __mmap_switched_data, . - __mmap_switched_data + +/* + * This provides a C-API version of __lookup_machine_type + */ +ENTRY(lookup_machine_type) + stmfd sp!, {r4 - r6, lr} + mov r1, r0 + bl __lookup_machine_type + mov r0, r5 + ldmfd sp!, {r4 - r6, pc} +ENDPROC(lookup_machine_type) + +/* + * This provides a C-API version of __lookup_processor_type + */ +ENTRY(lookup_processor_type) + stmfd sp!, {r4 - r6, r9, lr} + mov r9, r0 + bl __lookup_processor_type + mov r0, r5 + ldmfd sp!, {r4 - r6, r9, pc} +ENDPROC(lookup_processor_type) + +/* + * Read processor ID register (CP#15, CR0), and look up in the linker-built + * supported processor list. Note that we can't use the absolute addresses + * for the __proc_info lists since we aren't running with the MMU on + * (and therefore, we are not in the correct address space). We have to + * calculate the offset. + * + * r9 = cpuid + * Returns: + * r3, r4, r6 corrupted + * r5 = proc_info pointer in physical address space + * r9 = cpuid (preserved) + */ + __CPUINIT +__lookup_processor_type: + adr r3, __lookup_processor_type_data + ldmia r3, {r4 - r6} + sub r3, r3, r4 @ get offset between virt&phys + add r5, r5, r3 @ convert virt addresses to + add r6, r6, r3 @ physical address space +1: ldmia r5, {r3, r4} @ value, mask + and r4, r4, r9 @ mask wanted bits + teq r3, r4 + beq 2f + add r5, r5, #PROC_INFO_SZ @ sizeof(proc_info_list) + cmp r5, r6 + blo 1b + mov r5, #0 @ unknown processor +2: mov pc, lr +ENDPROC(__lookup_processor_type) + +/* + * Look in for information about the __proc_info structure. + */ + .align 2 + .type __lookup_processor_type_data, %object +__lookup_processor_type_data: + .long . + .long __proc_info_begin + .long __proc_info_end + .size __lookup_processor_type_data, . - __lookup_processor_type_data + +__error_p: +#ifdef CONFIG_DEBUG_LL + adr r0, str_p1 + bl printascii + mov r0, r9 + bl printhex8 + adr r0, str_p2 + bl printascii + b __error +str_p1: .asciz "\nError: unrecognized/unsupported processor variant (0x" +str_p2: .asciz ").\n" + .align +#endif +ENDPROC(__error_p) + +__error: +#ifdef CONFIG_ARCH_RPC +/* + * Turn the screen red on a error - RiscPC only. + */ + mov r0, #0x02000000 + mov r3, #0x11 + orr r3, r3, r3, lsl #8 + orr r3, r3, r3, lsl #16 + str r3, [r0], #4 + str r3, [r0], #4 + str r3, [r0], #4 + str r3, [r0], #4 +#endif +1: mov r0, r0 + b 1b +ENDPROC(__error) diff --git a/arch/arm/kernel/head-nommu.S b/arch/arm/kernel/head-nommu.S index 573b803dc6bf66..814ce1a732706d 100644 --- a/arch/arm/kernel/head-nommu.S +++ b/arch/arm/kernel/head-nommu.S @@ -48,8 +48,6 @@ ENTRY(stext) movs r8, r5 @ invalid machine (r5=0)? beq __error_a @ yes, error 'a' - ldr r13, __switch_data @ address to jump to after - @ the initialization is done adr lr, BSYM(__after_proc_init) @ return (PIC) address ARM( add pc, r10, #PROCINFO_INITFUNC ) THUMB( add r12, r10, #PROCINFO_INITFUNC ) @@ -87,8 +85,7 @@ __after_proc_init: mcr p15, 0, r0, c1, c0, 0 @ write control reg #endif /* CONFIG_CPU_CP15 */ - mov r3, r13 - mov pc, r3 @ clear the BSS and jump + b __mmap_switched @ clear the BSS and jump @ to start_kernel ENDPROC(__after_proc_init) .ltorg diff --git a/arch/arm/kernel/head.S b/arch/arm/kernel/head.S index eb62bf947212ab..dd6b369ac69cae 100644 --- a/arch/arm/kernel/head.S +++ b/arch/arm/kernel/head.S @@ -22,6 +22,10 @@ #include #include +#ifdef CONFIG_DEBUG_LL +#include +#endif + #if (PHYS_OFFSET & 0x001fffff) #error "PHYS_OFFSET must be at an even 2MiB boundary!" #endif @@ -86,6 +90,9 @@ ENTRY(stext) movs r8, r5 @ invalid machine (r5=0)? beq __error_a @ yes, error 'a' bl __vet_atags +#ifdef CONFIG_SMP_ON_UP + bl __fixup_smp +#endif bl __create_page_tables /* @@ -95,113 +102,15 @@ ENTRY(stext) * above. On return, the CPU will be ready for the MMU to be * turned on, and r0 will hold the CPU control register value. */ - ldr r13, __switch_data @ address to jump to after + ldr r13, =__mmap_switched @ address to jump to after @ mmu has been enabled - adr lr, BSYM(__enable_mmu) @ return (PIC) address + adr lr, BSYM(1f) @ return (PIC) address ARM( add pc, r10, #PROCINFO_INITFUNC ) THUMB( add r12, r10, #PROCINFO_INITFUNC ) THUMB( mov pc, r12 ) +1: b __enable_mmu ENDPROC(stext) - -#if defined(CONFIG_SMP) -ENTRY(secondary_startup) - /* - * Common entry point for secondary CPUs. - * - * Ensure that we're in SVC mode, and IRQs are disabled. Lookup - * the processor type - there is no need to check the machine type - * as it has already been validated by the primary processor. - */ - setmode PSR_F_BIT | PSR_I_BIT | SVC_MODE, r9 - mrc p15, 0, r9, c0, c0 @ get processor id - bl __lookup_processor_type - movs r10, r5 @ invalid processor? - moveq r0, #'p' @ yes, error 'p' - beq __error - - /* - * Use the page tables supplied from __cpu_up. - */ - adr r4, __secondary_data - ldmia r4, {r5, r7, r12} @ address to jump to after - sub r4, r4, r5 @ mmu has been enabled - ldr r4, [r7, r4] @ get secondary_data.pgdir - adr lr, BSYM(__enable_mmu) @ return address - mov r13, r12 @ __secondary_switched address - ARM( add pc, r10, #PROCINFO_INITFUNC ) @ initialise processor - @ (return control reg) - THUMB( add r12, r10, #PROCINFO_INITFUNC ) - THUMB( mov pc, r12 ) -ENDPROC(secondary_startup) - - /* - * r6 = &secondary_data - */ -ENTRY(__secondary_switched) - ldr sp, [r7, #4] @ get secondary_data.stack - mov fp, #0 - b secondary_start_kernel -ENDPROC(__secondary_switched) - - .type __secondary_data, %object -__secondary_data: - .long . - .long secondary_data - .long __secondary_switched -#endif /* defined(CONFIG_SMP) */ - - - -/* - * Setup common bits before finally enabling the MMU. Essentially - * this is just loading the page table pointer and domain access - * registers. - */ -__enable_mmu: -#ifdef CONFIG_ALIGNMENT_TRAP - orr r0, r0, #CR_A -#else - bic r0, r0, #CR_A -#endif -#ifdef CONFIG_CPU_DCACHE_DISABLE - bic r0, r0, #CR_C -#endif -#ifdef CONFIG_CPU_BPREDICT_DISABLE - bic r0, r0, #CR_Z -#endif -#ifdef CONFIG_CPU_ICACHE_DISABLE - bic r0, r0, #CR_I -#endif - mov r5, #(domain_val(DOMAIN_USER, DOMAIN_MANAGER) | \ - domain_val(DOMAIN_KERNEL, DOMAIN_MANAGER) | \ - domain_val(DOMAIN_TABLE, DOMAIN_MANAGER) | \ - domain_val(DOMAIN_IO, DOMAIN_CLIENT)) - mcr p15, 0, r5, c3, c0, 0 @ load domain access register - mcr p15, 0, r4, c2, c0, 0 @ load page table pointer - b __turn_mmu_on -ENDPROC(__enable_mmu) - -/* - * Enable the MMU. This completely changes the structure of the visible - * memory space. You will not be able to trace execution through this. - * If you have an enquiry about this, *please* check the linux-arm-kernel - * mailing list archives BEFORE sending another post to the list. - * - * r0 = cp#15 control register - * r13 = *virtual* address to jump to upon completion - * - * other registers depend on the function called upon completion - */ - .align 5 -__turn_mmu_on: - mov r0, r0 - mcr p15, 0, r0, c1, c0, 0 @ write control reg - mrc p15, 0, r3, c0, c0, 0 @ read id reg - mov r3, r3 - mov r3, r13 - mov pc, r3 -ENDPROC(__turn_mmu_on) - + .ltorg /* * Setup the initial page tables. We only setup the barest @@ -213,7 +122,7 @@ ENDPROC(__turn_mmu_on) * r10 = procinfo * * Returns: - * r0, r3, r6, r7 corrupted + * r0, r3, r5-r7 corrupted * r4 = physical page table address */ __create_page_tables: @@ -235,20 +144,30 @@ __create_page_tables: ldr r7, [r10, #PROCINFO_MM_MMUFLAGS] @ mm_mmuflags /* - * Create identity mapping for first MB of kernel to - * cater for the MMU enable. This identity mapping - * will be removed by paging_init(). We use our current program - * counter to determine corresponding section base address. + * Create identity mapping to cater for __enable_mmu. + * This identity mapping will be removed by paging_init(). */ - mov r6, pc - mov r6, r6, lsr #20 @ start of kernel section - orr r3, r7, r6, lsl #20 @ flags + kernel base - str r3, [r4, r6, lsl #2] @ identity mapping + adr r0, __enable_mmu_loc + ldmia r0, {r3, r5, r6} + sub r0, r0, r3 @ virt->phys offset + add r5, r5, r0 @ phys __enable_mmu + add r6, r6, r0 @ phys __enable_mmu_end + mov r5, r5, lsr #20 + mov r6, r6, lsr #20 + +1: orr r3, r7, r5, lsl #20 @ flags + kernel base + str r3, [r4, r5, lsl #2] @ identity mapping + teq r5, r6 + addne r5, r5, #1 @ next section + bne 1b /* * Now setup the pagetables for our kernel direct * mapped region. */ + mov r3, pc + mov r3, r3, lsr #20 + orr r3, r7, r3, lsl #20 add r0, r4, #(KERNEL_START & 0xff000000) >> 18 str r3, [r0, #(KERNEL_START & 0x00f00000) >> 18]! ldr r6, =(KERNEL_END - 1) @@ -289,24 +208,35 @@ __create_page_tables: str r6, [r0] #ifdef CONFIG_DEBUG_LL - ldr r7, [r10, #PROCINFO_IO_MMUFLAGS] @ io_mmuflags +#ifndef CONFIG_DEBUG_ICEDCC /* * Map in IO space for serial debugging. * This allows debug messages to be output * via a serial console before paging_init. */ - ldr r3, [r8, #MACHINFO_PGOFFIO] + addruart r7, r3 + + mov r3, r3, lsr #20 + mov r3, r3, lsl #2 + add r0, r4, r3 rsb r3, r3, #0x4000 @ PTRS_PER_PGD*sizeof(long) cmp r3, #0x0800 @ limit to 512MB movhi r3, #0x0800 add r6, r0, r3 - ldr r3, [r8, #MACHINFO_PHYSIO] - orr r3, r3, r7 + mov r3, r7, lsr #20 + ldr r7, [r10, #PROCINFO_IO_MMUFLAGS] @ io_mmuflags + orr r3, r7, r3, lsl #20 1: str r3, [r0], #4 add r3, r3, #1 << 20 teq r0, r6 bne 1b + +#else /* CONFIG_DEBUG_ICEDCC */ + /* we don't need any serial debugging mappings for ICEDCC */ + ldr r7, [r10, #PROCINFO_IO_MMUFLAGS] @ io_mmuflags +#endif /* !CONFIG_DEBUG_ICEDCC */ + #if defined(CONFIG_ARCH_NETWINDER) || defined(CONFIG_ARCH_CATS) /* * If we're using the NetWinder or CATS, we also need to map @@ -332,5 +262,168 @@ __create_page_tables: mov pc, lr ENDPROC(__create_page_tables) .ltorg +__enable_mmu_loc: + .long . + .long __enable_mmu + .long __enable_mmu_end + +#if defined(CONFIG_SMP) + __CPUINIT +ENTRY(secondary_startup) + /* + * Common entry point for secondary CPUs. + * + * Ensure that we're in SVC mode, and IRQs are disabled. Lookup + * the processor type - there is no need to check the machine type + * as it has already been validated by the primary processor. + */ + setmode PSR_F_BIT | PSR_I_BIT | SVC_MODE, r9 + mrc p15, 0, r9, c0, c0 @ get processor id + bl __lookup_processor_type + movs r10, r5 @ invalid processor? + moveq r0, #'p' @ yes, error 'p' + beq __error_p + + /* + * Use the page tables supplied from __cpu_up. + */ + adr r4, __secondary_data + ldmia r4, {r5, r7, r12} @ address to jump to after + sub r4, r4, r5 @ mmu has been enabled + ldr r4, [r7, r4] @ get secondary_data.pgdir + adr lr, BSYM(__enable_mmu) @ return address + mov r13, r12 @ __secondary_switched address + ARM( add pc, r10, #PROCINFO_INITFUNC ) @ initialise processor + @ (return control reg) + THUMB( add r12, r10, #PROCINFO_INITFUNC ) + THUMB( mov pc, r12 ) +ENDPROC(secondary_startup) + + /* + * r6 = &secondary_data + */ +ENTRY(__secondary_switched) + ldr sp, [r7, #4] @ get secondary_data.stack + mov fp, #0 + b secondary_start_kernel +ENDPROC(__secondary_switched) + + .type __secondary_data, %object +__secondary_data: + .long . + .long secondary_data + .long __secondary_switched +#endif /* defined(CONFIG_SMP) */ + + + +/* + * Setup common bits before finally enabling the MMU. Essentially + * this is just loading the page table pointer and domain access + * registers. + * + * r0 = cp#15 control register + * r1 = machine ID + * r2 = atags pointer + * r4 = page table pointer + * r9 = processor ID + * r13 = *virtual* address to jump to upon completion + */ +__enable_mmu: +#ifdef CONFIG_ALIGNMENT_TRAP + orr r0, r0, #CR_A +#else + bic r0, r0, #CR_A +#endif +#ifdef CONFIG_CPU_DCACHE_DISABLE + bic r0, r0, #CR_C +#endif +#ifdef CONFIG_CPU_BPREDICT_DISABLE + bic r0, r0, #CR_Z +#endif +#ifdef CONFIG_CPU_ICACHE_DISABLE + bic r0, r0, #CR_I +#endif + mov r5, #(domain_val(DOMAIN_USER, DOMAIN_MANAGER) | \ + domain_val(DOMAIN_KERNEL, DOMAIN_MANAGER) | \ + domain_val(DOMAIN_TABLE, DOMAIN_MANAGER) | \ + domain_val(DOMAIN_IO, DOMAIN_CLIENT)) + mcr p15, 0, r5, c3, c0, 0 @ load domain access register + mcr p15, 0, r4, c2, c0, 0 @ load page table pointer + b __turn_mmu_on +ENDPROC(__enable_mmu) + +/* + * Enable the MMU. This completely changes the structure of the visible + * memory space. You will not be able to trace execution through this. + * If you have an enquiry about this, *please* check the linux-arm-kernel + * mailing list archives BEFORE sending another post to the list. + * + * r0 = cp#15 control register + * r1 = machine ID + * r2 = atags pointer + * r9 = processor ID + * r13 = *virtual* address to jump to upon completion + * + * other registers depend on the function called upon completion + */ + .align 5 +__turn_mmu_on: + mov r0, r0 + mcr p15, 0, r0, c1, c0, 0 @ write control reg + mrc p15, 0, r3, c0, c0, 0 @ read id reg + mov r3, r3 + mov r3, r13 + mov pc, r3 +__enable_mmu_end: +ENDPROC(__turn_mmu_on) + + +#ifdef CONFIG_SMP_ON_UP +__fixup_smp: + mov r7, #0x00070000 + orr r6, r7, #0xff000000 @ mask 0xff070000 + orr r7, r7, #0x41000000 @ val 0x41070000 + and r0, r9, r6 + teq r0, r7 @ ARM CPU and ARMv6/v7? + bne __fixup_smp_on_up @ no, assume UP + + orr r6, r6, #0x0000ff00 + orr r6, r6, #0x000000f0 @ mask 0xff07fff0 + orr r7, r7, #0x0000b000 + orr r7, r7, #0x00000020 @ val 0x4107b020 + and r0, r9, r6 + teq r0, r7 @ ARM 11MPCore? + moveq pc, lr @ yes, assume SMP + + mrc p15, 0, r0, c0, c0, 5 @ read MPIDR + tst r0, #1 << 31 + movne pc, lr @ bit 31 => SMP + +__fixup_smp_on_up: + adr r0, 1f + ldmia r0, {r3, r6, r7} + sub r3, r0, r3 + add r6, r6, r3 + add r7, r7, r3 +2: cmp r6, r7 + ldmia r6!, {r0, r4} + strlo r4, [r0, r3] + blo 2b + mov pc, lr +ENDPROC(__fixup_smp) + +1: .word . + .word __smpalt_begin + .word __smpalt_end + + .pushsection .data + .globl smp_on_up +smp_on_up: + ALT_SMP(.long 1) + ALT_UP(.long 0) + .popsection + +#endif #include "head-common.S" diff --git a/arch/arm/kernel/hw_breakpoint.c b/arch/arm/kernel/hw_breakpoint.c new file mode 100644 index 00000000000000..54593b0c241b4e --- /dev/null +++ b/arch/arm/kernel/hw_breakpoint.c @@ -0,0 +1,849 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + * + * Copyright (C) 2009, 2010 ARM Limited + * + * Author: Will Deacon + */ + +/* + * HW_breakpoint: a unified kernel/user-space hardware breakpoint facility, + * using the CPU's debug registers. + */ +#define pr_fmt(fmt) "hw-breakpoint: " fmt + +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include + +/* Breakpoint currently in use for each BRP. */ +static DEFINE_PER_CPU(struct perf_event *, bp_on_reg[ARM_MAX_BRP]); + +/* Watchpoint currently in use for each WRP. */ +static DEFINE_PER_CPU(struct perf_event *, wp_on_reg[ARM_MAX_WRP]); + +/* Number of BRP/WRP registers on this CPU. */ +static int core_num_brps; +static int core_num_wrps; + +/* Debug architecture version. */ +static u8 debug_arch; + +/* Maximum supported watchpoint length. */ +static u8 max_watchpoint_len; + +/* Determine number of BRP registers available. */ +static int get_num_brps(void) +{ + u32 didr; + ARM_DBG_READ(c0, 0, didr); + return ((didr >> 24) & 0xf) + 1; +} + +/* Determine number of WRP registers available. */ +static int get_num_wrps(void) +{ + /* + * FIXME: When a watchpoint fires, the only way to work out which + * watchpoint it was is by disassembling the faulting instruction + * and working out the address of the memory access. + * + * Furthermore, we can only do this if the watchpoint was precise + * since imprecise watchpoints prevent us from calculating register + * based addresses. + * + * For the time being, we only report 1 watchpoint register so we + * always know which watchpoint fired. In the future we can either + * add a disassembler and address generation emulator, or we can + * insert a check to see if the DFAR is set on watchpoint exception + * entry [the ARM ARM states that the DFAR is UNKNOWN, but + * experience shows that it is set on some implementations]. + */ + +#if 0 + u32 didr, wrps; + ARM_DBG_READ(c0, 0, didr); + return ((didr >> 28) & 0xf) + 1; +#endif + + return 1; +} + +int hw_breakpoint_slots(int type) +{ + /* + * We can be called early, so don't rely on + * our static variables being initialised. + */ + switch (type) { + case TYPE_INST: + return get_num_brps(); + case TYPE_DATA: + return get_num_wrps(); + default: + pr_warning("unknown slot type: %d\n", type); + return 0; + } +} + +/* Determine debug architecture. */ +static u8 get_debug_arch(void) +{ + u32 didr; + + /* Do we implement the extended CPUID interface? */ + if (((read_cpuid_id() >> 16) & 0xf) != 0xf) { + pr_warning("CPUID feature registers not supported. " + "Assuming v6 debug is present.\n"); + return ARM_DEBUG_ARCH_V6; + } + + ARM_DBG_READ(c0, 0, didr); + return (didr >> 16) & 0xf; +} + +/* Does this core support mismatch breakpoints? */ +static int core_has_mismatch_bps(void) +{ + return debug_arch >= ARM_DEBUG_ARCH_V7_ECP14 && core_num_brps > 1; +} + +u8 arch_get_debug_arch(void) +{ + return debug_arch; +} + +#define READ_WB_REG_CASE(OP2, M, VAL) \ + case ((OP2 << 4) + M): \ + ARM_DBG_READ(c ## M, OP2, VAL); \ + break + +#define WRITE_WB_REG_CASE(OP2, M, VAL) \ + case ((OP2 << 4) + M): \ + ARM_DBG_WRITE(c ## M, OP2, VAL);\ + break + +#define GEN_READ_WB_REG_CASES(OP2, VAL) \ + READ_WB_REG_CASE(OP2, 0, VAL); \ + READ_WB_REG_CASE(OP2, 1, VAL); \ + READ_WB_REG_CASE(OP2, 2, VAL); \ + READ_WB_REG_CASE(OP2, 3, VAL); \ + READ_WB_REG_CASE(OP2, 4, VAL); \ + READ_WB_REG_CASE(OP2, 5, VAL); \ + READ_WB_REG_CASE(OP2, 6, VAL); \ + READ_WB_REG_CASE(OP2, 7, VAL); \ + READ_WB_REG_CASE(OP2, 8, VAL); \ + READ_WB_REG_CASE(OP2, 9, VAL); \ + READ_WB_REG_CASE(OP2, 10, VAL); \ + READ_WB_REG_CASE(OP2, 11, VAL); \ + READ_WB_REG_CASE(OP2, 12, VAL); \ + READ_WB_REG_CASE(OP2, 13, VAL); \ + READ_WB_REG_CASE(OP2, 14, VAL); \ + READ_WB_REG_CASE(OP2, 15, VAL) + +#define GEN_WRITE_WB_REG_CASES(OP2, VAL) \ + WRITE_WB_REG_CASE(OP2, 0, VAL); \ + WRITE_WB_REG_CASE(OP2, 1, VAL); \ + WRITE_WB_REG_CASE(OP2, 2, VAL); \ + WRITE_WB_REG_CASE(OP2, 3, VAL); \ + WRITE_WB_REG_CASE(OP2, 4, VAL); \ + WRITE_WB_REG_CASE(OP2, 5, VAL); \ + WRITE_WB_REG_CASE(OP2, 6, VAL); \ + WRITE_WB_REG_CASE(OP2, 7, VAL); \ + WRITE_WB_REG_CASE(OP2, 8, VAL); \ + WRITE_WB_REG_CASE(OP2, 9, VAL); \ + WRITE_WB_REG_CASE(OP2, 10, VAL); \ + WRITE_WB_REG_CASE(OP2, 11, VAL); \ + WRITE_WB_REG_CASE(OP2, 12, VAL); \ + WRITE_WB_REG_CASE(OP2, 13, VAL); \ + WRITE_WB_REG_CASE(OP2, 14, VAL); \ + WRITE_WB_REG_CASE(OP2, 15, VAL) + +static u32 read_wb_reg(int n) +{ + u32 val = 0; + + switch (n) { + GEN_READ_WB_REG_CASES(ARM_OP2_BVR, val); + GEN_READ_WB_REG_CASES(ARM_OP2_BCR, val); + GEN_READ_WB_REG_CASES(ARM_OP2_WVR, val); + GEN_READ_WB_REG_CASES(ARM_OP2_WCR, val); + default: + pr_warning("attempt to read from unknown breakpoint " + "register %d\n", n); + } + + return val; +} + +static void write_wb_reg(int n, u32 val) +{ + switch (n) { + GEN_WRITE_WB_REG_CASES(ARM_OP2_BVR, val); + GEN_WRITE_WB_REG_CASES(ARM_OP2_BCR, val); + GEN_WRITE_WB_REG_CASES(ARM_OP2_WVR, val); + GEN_WRITE_WB_REG_CASES(ARM_OP2_WCR, val); + default: + pr_warning("attempt to write to unknown breakpoint " + "register %d\n", n); + } + isb(); +} + +/* + * In order to access the breakpoint/watchpoint control registers, + * we must be running in debug monitor mode. Unfortunately, we can + * be put into halting debug mode at any time by an external debugger + * but there is nothing we can do to prevent that. + */ +static int enable_monitor_mode(void) +{ + u32 dscr; + int ret = 0; + + ARM_DBG_READ(c1, 0, dscr); + + /* Ensure that halting mode is disabled. */ + if (WARN_ONCE(dscr & ARM_DSCR_HDBGEN, "halting debug mode enabled." + "Unable to access hardware resources.")) { + ret = -EPERM; + goto out; + } + + /* Write to the corresponding DSCR. */ + switch (debug_arch) { + case ARM_DEBUG_ARCH_V6: + case ARM_DEBUG_ARCH_V6_1: + ARM_DBG_WRITE(c1, 0, (dscr | ARM_DSCR_MDBGEN)); + break; + case ARM_DEBUG_ARCH_V7_ECP14: + ARM_DBG_WRITE(c2, 2, (dscr | ARM_DSCR_MDBGEN)); + break; + default: + ret = -ENODEV; + goto out; + } + + /* Check that the write made it through. */ + ARM_DBG_READ(c1, 0, dscr); + if (WARN_ONCE(!(dscr & ARM_DSCR_MDBGEN), + "failed to enable monitor mode.")) { + ret = -EPERM; + } + +out: + return ret; +} + +/* + * Check if 8-bit byte-address select is available. + * This clobbers WRP 0. + */ +static u8 get_max_wp_len(void) +{ + u32 ctrl_reg; + struct arch_hw_breakpoint_ctrl ctrl; + u8 size = 4; + + if (debug_arch < ARM_DEBUG_ARCH_V7_ECP14) + goto out; + + if (enable_monitor_mode()) + goto out; + + memset(&ctrl, 0, sizeof(ctrl)); + ctrl.len = ARM_BREAKPOINT_LEN_8; + ctrl_reg = encode_ctrl_reg(ctrl); + + write_wb_reg(ARM_BASE_WVR, 0); + write_wb_reg(ARM_BASE_WCR, ctrl_reg); + if ((read_wb_reg(ARM_BASE_WCR) & ctrl_reg) == ctrl_reg) + size = 8; + +out: + return size; +} + +u8 arch_get_max_wp_len(void) +{ + return max_watchpoint_len; +} + +/* + * Handler for reactivating a suspended watchpoint when the single + * step `mismatch' breakpoint is triggered. + */ +static void wp_single_step_handler(struct perf_event *bp, int unused, + struct perf_sample_data *data, + struct pt_regs *regs) +{ + perf_event_enable(counter_arch_bp(bp)->suspended_wp); + unregister_hw_breakpoint(bp); +} + +static int bp_is_single_step(struct perf_event *bp) +{ + return bp->overflow_handler == wp_single_step_handler; +} + +/* + * Install a perf counter breakpoint. + */ +int arch_install_hw_breakpoint(struct perf_event *bp) +{ + struct arch_hw_breakpoint *info = counter_arch_bp(bp); + struct perf_event **slot, **slots; + int i, max_slots, ctrl_base, val_base, ret = 0; + + /* Ensure that we are in monitor mode and halting mode is disabled. */ + ret = enable_monitor_mode(); + if (ret) + goto out; + + if (info->ctrl.type == ARM_BREAKPOINT_EXECUTE) { + /* Breakpoint */ + ctrl_base = ARM_BASE_BCR; + val_base = ARM_BASE_BVR; + slots = __get_cpu_var(bp_on_reg); + max_slots = core_num_brps - 1; + + if (bp_is_single_step(bp)) { + info->ctrl.mismatch = 1; + i = max_slots; + slots[i] = bp; + goto setup; + } + } else { + /* Watchpoint */ + ctrl_base = ARM_BASE_WCR; + val_base = ARM_BASE_WVR; + slots = __get_cpu_var(wp_on_reg); + max_slots = core_num_wrps; + } + + for (i = 0; i < max_slots; ++i) { + slot = &slots[i]; + + if (!*slot) { + *slot = bp; + break; + } + } + + if (WARN_ONCE(i == max_slots, "Can't find any breakpoint slot")) { + ret = -EBUSY; + goto out; + } + +setup: + /* Setup the address register. */ + write_wb_reg(val_base + i, info->address); + + /* Setup the control register. */ + write_wb_reg(ctrl_base + i, encode_ctrl_reg(info->ctrl) | 0x1); + +out: + return ret; +} + +void arch_uninstall_hw_breakpoint(struct perf_event *bp) +{ + struct arch_hw_breakpoint *info = counter_arch_bp(bp); + struct perf_event **slot, **slots; + int i, max_slots, base; + + if (info->ctrl.type == ARM_BREAKPOINT_EXECUTE) { + /* Breakpoint */ + base = ARM_BASE_BCR; + slots = __get_cpu_var(bp_on_reg); + max_slots = core_num_brps - 1; + + if (bp_is_single_step(bp)) { + i = max_slots; + slots[i] = NULL; + goto reset; + } + } else { + /* Watchpoint */ + base = ARM_BASE_WCR; + slots = __get_cpu_var(wp_on_reg); + max_slots = core_num_wrps; + } + + /* Remove the breakpoint. */ + for (i = 0; i < max_slots; ++i) { + slot = &slots[i]; + + if (*slot == bp) { + *slot = NULL; + break; + } + } + + if (WARN_ONCE(i == max_slots, "Can't find any breakpoint slot")) + return; + +reset: + /* Reset the control register. */ + write_wb_reg(base + i, 0); +} + +static int get_hbp_len(u8 hbp_len) +{ + unsigned int len_in_bytes = 0; + + switch (hbp_len) { + case ARM_BREAKPOINT_LEN_1: + len_in_bytes = 1; + break; + case ARM_BREAKPOINT_LEN_2: + len_in_bytes = 2; + break; + case ARM_BREAKPOINT_LEN_4: + len_in_bytes = 4; + break; + case ARM_BREAKPOINT_LEN_8: + len_in_bytes = 8; + break; + } + + return len_in_bytes; +} + +/* + * Check whether bp virtual address is in kernel space. + */ +int arch_check_bp_in_kernelspace(struct perf_event *bp) +{ + unsigned int len; + unsigned long va; + struct arch_hw_breakpoint *info = counter_arch_bp(bp); + + va = info->address; + len = get_hbp_len(info->ctrl.len); + + return (va >= TASK_SIZE) && ((va + len - 1) >= TASK_SIZE); +} + +/* + * Extract generic type and length encodings from an arch_hw_breakpoint_ctrl. + * Hopefully this will disappear when ptrace can bypass the conversion + * to generic breakpoint descriptions. + */ +int arch_bp_generic_fields(struct arch_hw_breakpoint_ctrl ctrl, + int *gen_len, int *gen_type) +{ + /* Type */ + switch (ctrl.type) { + case ARM_BREAKPOINT_EXECUTE: + *gen_type = HW_BREAKPOINT_X; + break; + case ARM_BREAKPOINT_LOAD: + *gen_type = HW_BREAKPOINT_R; + break; + case ARM_BREAKPOINT_STORE: + *gen_type = HW_BREAKPOINT_W; + break; + case ARM_BREAKPOINT_LOAD | ARM_BREAKPOINT_STORE: + *gen_type = HW_BREAKPOINT_RW; + break; + default: + return -EINVAL; + } + + /* Len */ + switch (ctrl.len) { + case ARM_BREAKPOINT_LEN_1: + *gen_len = HW_BREAKPOINT_LEN_1; + break; + case ARM_BREAKPOINT_LEN_2: + *gen_len = HW_BREAKPOINT_LEN_2; + break; + case ARM_BREAKPOINT_LEN_4: + *gen_len = HW_BREAKPOINT_LEN_4; + break; + case ARM_BREAKPOINT_LEN_8: + *gen_len = HW_BREAKPOINT_LEN_8; + break; + default: + return -EINVAL; + } + + return 0; +} + +/* + * Construct an arch_hw_breakpoint from a perf_event. + */ +static int arch_build_bp_info(struct perf_event *bp) +{ + struct arch_hw_breakpoint *info = counter_arch_bp(bp); + + /* Type */ + switch (bp->attr.bp_type) { + case HW_BREAKPOINT_X: + info->ctrl.type = ARM_BREAKPOINT_EXECUTE; + break; + case HW_BREAKPOINT_R: + info->ctrl.type = ARM_BREAKPOINT_LOAD; + break; + case HW_BREAKPOINT_W: + info->ctrl.type = ARM_BREAKPOINT_STORE; + break; + case HW_BREAKPOINT_RW: + info->ctrl.type = ARM_BREAKPOINT_LOAD | ARM_BREAKPOINT_STORE; + break; + default: + return -EINVAL; + } + + /* Len */ + switch (bp->attr.bp_len) { + case HW_BREAKPOINT_LEN_1: + info->ctrl.len = ARM_BREAKPOINT_LEN_1; + break; + case HW_BREAKPOINT_LEN_2: + info->ctrl.len = ARM_BREAKPOINT_LEN_2; + break; + case HW_BREAKPOINT_LEN_4: + info->ctrl.len = ARM_BREAKPOINT_LEN_4; + break; + case HW_BREAKPOINT_LEN_8: + info->ctrl.len = ARM_BREAKPOINT_LEN_8; + if ((info->ctrl.type != ARM_BREAKPOINT_EXECUTE) + && max_watchpoint_len >= 8) + break; + default: + return -EINVAL; + } + + /* Address */ + info->address = bp->attr.bp_addr; + + /* Privilege */ + info->ctrl.privilege = ARM_BREAKPOINT_USER; + if (arch_check_bp_in_kernelspace(bp) && !bp_is_single_step(bp)) + info->ctrl.privilege |= ARM_BREAKPOINT_PRIV; + + /* Enabled? */ + info->ctrl.enabled = !bp->attr.disabled; + + /* Mismatch */ + info->ctrl.mismatch = 0; + + return 0; +} + +/* + * Validate the arch-specific HW Breakpoint register settings. + */ +int arch_validate_hwbkpt_settings(struct perf_event *bp) +{ + struct arch_hw_breakpoint *info = counter_arch_bp(bp); + int ret = 0; + u32 bytelen, max_len, offset, alignment_mask = 0x3; + + /* Build the arch_hw_breakpoint. */ + ret = arch_build_bp_info(bp); + if (ret) + goto out; + + /* Check address alignment. */ + if (info->ctrl.len == ARM_BREAKPOINT_LEN_8) + alignment_mask = 0x7; + if (info->address & alignment_mask) { + /* + * Try to fix the alignment. This may result in a length + * that is too large, so we must check for that. + */ + bytelen = get_hbp_len(info->ctrl.len); + max_len = info->ctrl.type == ARM_BREAKPOINT_EXECUTE ? 4 : + max_watchpoint_len; + + if (max_len >= 8) + offset = info->address & 0x7; + else + offset = info->address & 0x3; + + if (bytelen > (1 << ((max_len - (offset + 1)) >> 1))) { + ret = -EFBIG; + goto out; + } + + info->ctrl.len <<= offset; + info->address &= ~offset; + + pr_debug("breakpoint alignment fixup: length = 0x%x, " + "address = 0x%x\n", info->ctrl.len, info->address); + } + + /* + * Currently we rely on an overflow handler to take + * care of single-stepping the breakpoint when it fires. + * In the case of userspace breakpoints on a core with V7 debug, + * we can use the mismatch feature as a poor-man's hardware single-step. + */ + if (WARN_ONCE(!bp->overflow_handler && + (arch_check_bp_in_kernelspace(bp) || !core_has_mismatch_bps()), + "overflow handler required but none found")) { + ret = -EINVAL; + goto out; + } +out: + return ret; +} + +static void update_mismatch_flag(int idx, int flag) +{ + struct perf_event *bp = __get_cpu_var(bp_on_reg[idx]); + struct arch_hw_breakpoint *info; + + if (bp == NULL) + return; + + info = counter_arch_bp(bp); + + /* Update the mismatch field to enter/exit `single-step' mode */ + if (!bp->overflow_handler && info->ctrl.mismatch != flag) { + info->ctrl.mismatch = flag; + write_wb_reg(ARM_BASE_BCR + idx, encode_ctrl_reg(info->ctrl) | 0x1); + } +} + +static void watchpoint_handler(unsigned long unknown, struct pt_regs *regs) +{ + int i; + struct perf_event *bp, **slots = __get_cpu_var(wp_on_reg); + struct arch_hw_breakpoint *info; + struct perf_event_attr attr; + + /* Without a disassembler, we can only handle 1 watchpoint. */ + BUG_ON(core_num_wrps > 1); + + hw_breakpoint_init(&attr); + attr.bp_addr = regs->ARM_pc & ~0x3; + attr.bp_len = HW_BREAKPOINT_LEN_4; + attr.bp_type = HW_BREAKPOINT_X; + + for (i = 0; i < core_num_wrps; ++i) { + rcu_read_lock(); + + if (slots[i] == NULL) { + rcu_read_unlock(); + continue; + } + + /* + * The DFAR is an unknown value. Since we only allow a + * single watchpoint, we can set the trigger to the lowest + * possible faulting address. + */ + info = counter_arch_bp(slots[i]); + info->trigger = slots[i]->attr.bp_addr; + pr_debug("watchpoint fired: address = 0x%x\n", info->trigger); + perf_bp_event(slots[i], regs); + + /* + * If no overflow handler is present, insert a temporary + * mismatch breakpoint so we can single-step over the + * watchpoint trigger. + */ + if (!slots[i]->overflow_handler) { + bp = register_user_hw_breakpoint(&attr, + wp_single_step_handler, + current); + counter_arch_bp(bp)->suspended_wp = slots[i]; + perf_event_disable(slots[i]); + } + + rcu_read_unlock(); + } +} + +static void breakpoint_handler(unsigned long unknown, struct pt_regs *regs) +{ + int i; + int mismatch; + u32 ctrl_reg, val, addr; + struct perf_event *bp, **slots = __get_cpu_var(bp_on_reg); + struct arch_hw_breakpoint *info; + struct arch_hw_breakpoint_ctrl ctrl; + + /* The exception entry code places the amended lr in the PC. */ + addr = regs->ARM_pc; + + for (i = 0; i < core_num_brps; ++i) { + rcu_read_lock(); + + bp = slots[i]; + + if (bp == NULL) { + rcu_read_unlock(); + continue; + } + + mismatch = 0; + + /* Check if the breakpoint value matches. */ + val = read_wb_reg(ARM_BASE_BVR + i); + if (val != (addr & ~0x3)) + goto unlock; + + /* Possible match, check the byte address select to confirm. */ + ctrl_reg = read_wb_reg(ARM_BASE_BCR + i); + decode_ctrl_reg(ctrl_reg, &ctrl); + if ((1 << (addr & 0x3)) & ctrl.len) { + mismatch = 1; + info = counter_arch_bp(bp); + info->trigger = addr; + } + +unlock: + if ((mismatch && !info->ctrl.mismatch) || bp_is_single_step(bp)) { + pr_debug("breakpoint fired: address = 0x%x\n", addr); + perf_bp_event(bp, regs); + } + + update_mismatch_flag(i, mismatch); + rcu_read_unlock(); + } +} + +/* + * Called from either the Data Abort Handler [watchpoint] or the + * Prefetch Abort Handler [breakpoint]. + */ +static int hw_breakpoint_pending(unsigned long addr, unsigned int fsr, + struct pt_regs *regs) +{ + int ret = 1; /* Unhandled fault. */ + u32 dscr; + + /* We only handle watchpoints and hardware breakpoints. */ + ARM_DBG_READ(c1, 0, dscr); + + /* Perform perf callbacks. */ + switch (ARM_DSCR_MOE(dscr)) { + case ARM_ENTRY_BREAKPOINT: + breakpoint_handler(addr, regs); + break; + case ARM_ENTRY_ASYNC_WATCHPOINT: + WARN_ON("Asynchronous watchpoint exception taken. " + "Debugging results may be unreliable"); + case ARM_ENTRY_SYNC_WATCHPOINT: + watchpoint_handler(addr, regs); + break; + default: + goto out; + } + + ret = 0; +out: + return ret; +} + +/* + * One-time initialisation. + */ +static void __init reset_ctrl_regs(void *unused) +{ + int i; + + if (enable_monitor_mode()) + return; + + for (i = 0; i < core_num_brps; ++i) { + write_wb_reg(ARM_BASE_BCR + i, 0UL); + write_wb_reg(ARM_BASE_BVR + i, 0UL); + } + + for (i = 0; i < core_num_wrps; ++i) { + write_wb_reg(ARM_BASE_WCR + i, 0UL); + write_wb_reg(ARM_BASE_WVR + i, 0UL); + } +} + +static int __init arch_hw_breakpoint_init(void) +{ + int ret = 0; + u32 dscr; + + debug_arch = get_debug_arch(); + + if (debug_arch > ARM_DEBUG_ARCH_V7_ECP14) { + pr_info("debug architecture 0x%x unsupported.\n", debug_arch); + ret = -ENODEV; + goto out; + } + + /* Determine how many BRPs/WRPs are available. */ + core_num_brps = get_num_brps(); + core_num_wrps = get_num_wrps(); + + pr_info("found %d breakpoint and %d watchpoint registers.\n", + core_num_brps, core_num_wrps); + + if (core_has_mismatch_bps()) + pr_info("1 breakpoint reserved for watchpoint single-step.\n"); + + ARM_DBG_READ(c1, 0, dscr); + if (dscr & ARM_DSCR_HDBGEN) { + pr_warning("halting debug mode enabled. Assuming maximum " + "watchpoint size of 4 bytes."); + } else { + /* Work out the maximum supported watchpoint length. */ + max_watchpoint_len = get_max_wp_len(); + pr_info("maximum watchpoint size is %u bytes.\n", + max_watchpoint_len); + + /* + * Reset the breakpoint resources. We assume that a halting + * debugger will leave the world in a nice state for us. + */ + smp_call_function(reset_ctrl_regs, NULL, 1); + reset_ctrl_regs(NULL); + } + + /* Register debug fault handler. */ + hook_fault_code(2, hw_breakpoint_pending, SIGTRAP, TRAP_HWBKPT, + "watchpoint debug exception"); + hook_ifault_code(2, hw_breakpoint_pending, SIGTRAP, TRAP_HWBKPT, + "breakpoint debug exception"); + +out: + return ret; +} +arch_initcall(arch_hw_breakpoint_init); + +void hw_breakpoint_pmu_read(struct perf_event *bp) +{ +} + +/* + * Dummy function to register with die_notifier. + */ +int hw_breakpoint_exceptions_notify(struct notifier_block *unused, + unsigned long val, void *data) +{ + return NOTIFY_DONE; +} diff --git a/arch/arm/kernel/module.c b/arch/arm/kernel/module.c index 6b4605893f1e45..d9bd786ce23dc1 100644 --- a/arch/arm/kernel/module.c +++ b/arch/arm/kernel/module.c @@ -69,20 +69,31 @@ int module_frob_arch_sections(Elf_Ehdr *hdr, { #ifdef CONFIG_ARM_UNWIND Elf_Shdr *s, *sechdrs_end = sechdrs + hdr->e_shnum; + struct arm_unwind_mapping *maps = mod->arch.map; for (s = sechdrs; s < sechdrs_end; s++) { - if (strcmp(".ARM.exidx.init.text", secstrings + s->sh_name) == 0) - mod->arch.unw_sec_init = s; - else if (strcmp(".ARM.exidx.devinit.text", secstrings + s->sh_name) == 0) - mod->arch.unw_sec_devinit = s; - else if (strcmp(".ARM.exidx", secstrings + s->sh_name) == 0) - mod->arch.unw_sec_core = s; - else if (strcmp(".init.text", secstrings + s->sh_name) == 0) - mod->arch.sec_init_text = s; - else if (strcmp(".devinit.text", secstrings + s->sh_name) == 0) - mod->arch.sec_devinit_text = s; - else if (strcmp(".text", secstrings + s->sh_name) == 0) - mod->arch.sec_core_text = s; + char const *secname = secstrings + s->sh_name; + + if (strcmp(".ARM.exidx.init.text", secname) == 0) + maps[ARM_SEC_INIT].unw_sec = s; + else if (strcmp(".ARM.exidx.devinit.text", secname) == 0) + maps[ARM_SEC_DEVINIT].unw_sec = s; + else if (strcmp(".ARM.exidx", secname) == 0) + maps[ARM_SEC_CORE].unw_sec = s; + else if (strcmp(".ARM.exidx.exit.text", secname) == 0) + maps[ARM_SEC_EXIT].unw_sec = s; + else if (strcmp(".ARM.exidx.devexit.text", secname) == 0) + maps[ARM_SEC_DEVEXIT].unw_sec = s; + else if (strcmp(".init.text", secname) == 0) + maps[ARM_SEC_INIT].sec_text = s; + else if (strcmp(".devinit.text", secname) == 0) + maps[ARM_SEC_DEVINIT].sec_text = s; + else if (strcmp(".text", secname) == 0) + maps[ARM_SEC_CORE].sec_text = s; + else if (strcmp(".exit.text", secname) == 0) + maps[ARM_SEC_EXIT].sec_text = s; + else if (strcmp(".devexit.text", secname) == 0) + maps[ARM_SEC_DEVEXIT].sec_text = s; } #endif return 0; @@ -292,31 +303,22 @@ apply_relocate_add(Elf32_Shdr *sechdrs, const char *strtab, #ifdef CONFIG_ARM_UNWIND static void register_unwind_tables(struct module *mod) { - if (mod->arch.unw_sec_init && mod->arch.sec_init_text) - mod->arch.unwind_init = - unwind_table_add(mod->arch.unw_sec_init->sh_addr, - mod->arch.unw_sec_init->sh_size, - mod->arch.sec_init_text->sh_addr, - mod->arch.sec_init_text->sh_size); - if (mod->arch.unw_sec_devinit && mod->arch.sec_devinit_text) - mod->arch.unwind_devinit = - unwind_table_add(mod->arch.unw_sec_devinit->sh_addr, - mod->arch.unw_sec_devinit->sh_size, - mod->arch.sec_devinit_text->sh_addr, - mod->arch.sec_devinit_text->sh_size); - if (mod->arch.unw_sec_core && mod->arch.sec_core_text) - mod->arch.unwind_core = - unwind_table_add(mod->arch.unw_sec_core->sh_addr, - mod->arch.unw_sec_core->sh_size, - mod->arch.sec_core_text->sh_addr, - mod->arch.sec_core_text->sh_size); + int i; + for (i = 0; i < ARM_SEC_MAX; ++i) { + struct arm_unwind_mapping *map = &mod->arch.map[i]; + if (map->unw_sec && map->sec_text) + map->unwind = unwind_table_add(map->unw_sec->sh_addr, + map->unw_sec->sh_size, + map->sec_text->sh_addr, + map->sec_text->sh_size); + } } static void unregister_unwind_tables(struct module *mod) { - unwind_table_del(mod->arch.unwind_init); - unwind_table_del(mod->arch.unwind_devinit); - unwind_table_del(mod->arch.unwind_core); + int i = ARM_SEC_MAX; + while (--i >= 0) + unwind_table_del(mod->arch.map[i].unwind); } #else static inline void register_unwind_tables(struct module *mod) { } diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index 401e38be1f787c..e76fcaadce03fc 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -29,6 +29,7 @@ #include #include #include +#include #include #include @@ -135,6 +136,25 @@ EXPORT_SYMBOL(pm_power_off); void (*arm_pm_restart)(char str, const char *cmd) = arm_machine_restart; EXPORT_SYMBOL_GPL(arm_pm_restart); +static void do_nothing(void *unused) +{ +} + +/* + * cpu_idle_wait - Used to ensure that all the CPUs discard old value of + * pm_idle and update to new pm_idle value. Required while changing pm_idle + * handler on SMP systems. + * + * Caller must have changed pm_idle to the new value before the call. Old + * pm_idle value will not be used by any CPU after the return of this function. + */ +void cpu_idle_wait(void) +{ + smp_mb(); + /* kick all the CPUs so that they exit out of pm_idle */ + smp_call_function(do_nothing, NULL, 1); +} +EXPORT_SYMBOL_GPL(cpu_idle_wait); /* * This is our default idle handler. We need to disable @@ -317,6 +337,8 @@ void flush_thread(void) struct thread_info *thread = current_thread_info(); struct task_struct *tsk = current; + flush_ptrace_hw_breakpoint(tsk); + memset(thread->used_cp, 0, sizeof(thread->used_cp)); memset(&tsk->thread.debug, 0, sizeof(struct debug_info)); memset(&thread->fpstate, 0, sizeof(union fp_state)); @@ -345,6 +367,8 @@ copy_thread(unsigned long clone_flags, unsigned long stack_start, thread->cpu_context.sp = (unsigned long)childregs; thread->cpu_context.pc = (unsigned long)ret_from_fork; + clear_ptrace_hw_breakpoint(p); + if (clone_flags & CLONE_SETTLS) thread->tp_value = regs->ARM_r3; @@ -458,3 +482,24 @@ unsigned long arch_randomize_brk(struct mm_struct *mm) unsigned long range_end = mm->brk + 0x02000000; return randomize_range(mm->brk, range_end, 0) ? : mm->brk; } + +/* + * The vectors page is always readable from user space for the + * atomic helpers and the signal restart code. Let's declare a mapping + * for it so it is visible through ptrace and /proc//mem. + */ + +int vectors_user_mapping(void) +{ + struct mm_struct *mm = current->mm; + return install_special_mapping(mm, 0xffff0000, PAGE_SIZE, + VM_READ | VM_EXEC | + VM_MAYREAD | VM_MAYEXEC | + VM_ALWAYSDUMP | VM_RESERVED, + NULL); +} + +const char *arch_vma_name(struct vm_area_struct *vma) +{ + return (vma->vm_start == 0xffff0000) ? "[vectors]" : NULL; +} diff --git a/arch/arm/kernel/ptrace.c b/arch/arm/kernel/ptrace.c index f99d489822d50f..e0cb6370ed148d 100644 --- a/arch/arm/kernel/ptrace.c +++ b/arch/arm/kernel/ptrace.c @@ -19,6 +19,8 @@ #include #include #include +#include +#include #include #include @@ -847,6 +849,232 @@ static int ptrace_setvfpregs(struct task_struct *tsk, void __user *data) } #endif +#ifdef CONFIG_HAVE_HW_BREAKPOINT +/* + * Convert a virtual register number into an index for a thread_info + * breakpoint array. Breakpoints are identified using positive numbers + * whilst watchpoints are negative. The registers are laid out as pairs + * of (address, control), each pair mapping to a unique hw_breakpoint struct. + * Register 0 is reserved for describing resource information. + */ +static int ptrace_hbp_num_to_idx(long num) +{ + if (num < 0) + num = (ARM_MAX_BRP << 1) - num; + return (num - 1) >> 1; +} + +/* + * Returns the virtual register number for the address of the + * breakpoint at index idx. + */ +static long ptrace_hbp_idx_to_num(int idx) +{ + long mid = ARM_MAX_BRP << 1; + long num = (idx << 1) + 1; + return num > mid ? mid - num : num; +} + +/* + * Handle hitting a HW-breakpoint. + */ +static void ptrace_hbptriggered(struct perf_event *bp, int unused, + struct perf_sample_data *data, + struct pt_regs *regs) +{ + struct arch_hw_breakpoint *bkpt = counter_arch_bp(bp); + long num; + int i; + siginfo_t info; + + for (i = 0; i < ARM_MAX_HBP_SLOTS; ++i) + if (current->thread.debug.hbp[i] == bp) + break; + + num = (i == ARM_MAX_HBP_SLOTS) ? 0 : ptrace_hbp_idx_to_num(i); + + info.si_signo = SIGTRAP; + info.si_errno = (int)num; + info.si_code = TRAP_HWBKPT; + info.si_addr = (void __user *)(bkpt->trigger); + + force_sig_info(SIGTRAP, &info, current); +} + +/* + * Set ptrace breakpoint pointers to zero for this task. + * This is required in order to prevent child processes from unregistering + * breakpoints held by their parent. + */ +void clear_ptrace_hw_breakpoint(struct task_struct *tsk) +{ + memset(tsk->thread.debug.hbp, 0, sizeof(tsk->thread.debug.hbp)); +} + +/* + * Unregister breakpoints from this task and reset the pointers in + * the thread_struct. + */ +void flush_ptrace_hw_breakpoint(struct task_struct *tsk) +{ + int i; + struct thread_struct *t = &tsk->thread; + + for (i = 0; i < ARM_MAX_HBP_SLOTS; i++) { + if (t->debug.hbp[i]) { + unregister_hw_breakpoint(t->debug.hbp[i]); + t->debug.hbp[i] = NULL; + } + } +} + +static u32 ptrace_get_hbp_resource_info(void) +{ + u8 num_brps, num_wrps, debug_arch, wp_len; + u32 reg = 0; + + num_brps = hw_breakpoint_slots(TYPE_INST); + num_wrps = hw_breakpoint_slots(TYPE_DATA); + debug_arch = arch_get_debug_arch(); + wp_len = arch_get_max_wp_len(); + + reg |= debug_arch; + reg <<= 8; + reg |= wp_len; + reg <<= 8; + reg |= num_wrps; + reg <<= 8; + reg |= num_brps; + + return reg; +} + +static struct perf_event *ptrace_hbp_create(struct task_struct *tsk, int type) +{ + struct perf_event_attr attr; + + ptrace_breakpoint_init(&attr); + + /* Initialise fields to sane defaults. */ + attr.bp_addr = 0; + attr.bp_len = HW_BREAKPOINT_LEN_4; + attr.bp_type = type; + attr.disabled = 1; + + return register_user_hw_breakpoint(&attr, ptrace_hbptriggered, tsk); +} + +static int ptrace_gethbpregs(struct task_struct *tsk, long num, + unsigned long __user *data) +{ + u32 reg; + int idx, ret = 0; + struct perf_event *bp; + struct arch_hw_breakpoint_ctrl arch_ctrl; + + if (num == 0) { + reg = ptrace_get_hbp_resource_info(); + } else { + idx = ptrace_hbp_num_to_idx(num); + if (idx < 0 || idx >= ARM_MAX_HBP_SLOTS) { + ret = -EINVAL; + goto out; + } + + bp = tsk->thread.debug.hbp[idx]; + if (!bp) { + reg = 0; + goto put; + } + + arch_ctrl = counter_arch_bp(bp)->ctrl; + + /* + * Fix up the len because we may have adjusted it + * to compensate for an unaligned address. + */ + while (!(arch_ctrl.len & 0x1)) + arch_ctrl.len >>= 1; + + if (idx & 0x1) + reg = encode_ctrl_reg(arch_ctrl); + else + reg = bp->attr.bp_addr; + } + +put: + if (put_user(reg, data)) + ret = -EFAULT; + +out: + return ret; +} + +static int ptrace_sethbpregs(struct task_struct *tsk, long num, + unsigned long __user *data) +{ + int idx, gen_len, gen_type, implied_type, ret = 0; + u32 user_val; + struct perf_event *bp; + struct arch_hw_breakpoint_ctrl ctrl; + struct perf_event_attr attr; + + if (num == 0) + goto out; + else if (num < 0) + implied_type = HW_BREAKPOINT_RW; + else + implied_type = HW_BREAKPOINT_X; + + idx = ptrace_hbp_num_to_idx(num); + if (idx < 0 || idx >= ARM_MAX_HBP_SLOTS) { + ret = -EINVAL; + goto out; + } + + if (get_user(user_val, data)) { + ret = -EFAULT; + goto out; + } + + bp = tsk->thread.debug.hbp[idx]; + if (!bp) { + bp = ptrace_hbp_create(tsk, implied_type); + if (IS_ERR(bp)) { + ret = PTR_ERR(bp); + goto out; + } + tsk->thread.debug.hbp[idx] = bp; + } + + attr = bp->attr; + + if (num & 0x1) { + /* Address */ + attr.bp_addr = user_val; + } else { + /* Control */ + decode_ctrl_reg(user_val, &ctrl); + ret = arch_bp_generic_fields(ctrl, &gen_len, &gen_type); + if (ret) + goto out; + + if ((gen_type & implied_type) != gen_type) { + ret = -EINVAL; + goto out; + } + + attr.bp_len = gen_len; + attr.bp_type = gen_type; + attr.disabled = !ctrl.enabled; + } + + ret = modify_user_hw_breakpoint(bp, &attr); +out: + return ret; +} +#endif + long arch_ptrace(struct task_struct *child, long request, long addr, long data) { int ret; @@ -916,6 +1144,17 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data) break; #endif +#ifdef CONFIG_HAVE_HW_BREAKPOINT + case PTRACE_GETHBPREGS: + ret = ptrace_gethbpregs(child, addr, + (unsigned long __user *)data); + break; + case PTRACE_SETHBPREGS: + ret = ptrace_sethbpregs(child, addr, + (unsigned long __user *)data); + break; +#endif + default: ret = ptrace_request(child, request, addr, data); break; diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c index d5231ae7355aa2..336f14e0e5c212 100644 --- a/arch/arm/kernel/setup.c +++ b/arch/arm/kernel/setup.c @@ -36,6 +36,7 @@ #include #include #include +#include #include #include #include @@ -238,6 +239,35 @@ int cpu_architecture(void) return cpu_arch; } +static int cpu_has_aliasing_icache(unsigned int arch) +{ + int aliasing_icache; + unsigned int id_reg, num_sets, line_size; + + /* arch specifies the register format */ + switch (arch) { + case CPU_ARCH_ARMv7: + asm("mcr p15, 2, %0, c0, c0, 0 @ set CSSELR" + : /* No output operands */ + : "r" (1)); + isb(); + asm("mrc p15, 1, %0, c0, c0, 0 @ read CCSIDR" + : "=r" (id_reg)); + line_size = 4 << ((id_reg & 0x7) + 2); + num_sets = ((id_reg >> 13) & 0x7fff) + 1; + aliasing_icache = (line_size * num_sets) > PAGE_SIZE; + break; + case CPU_ARCH_ARMv6: + aliasing_icache = read_cpuid_cachetype() & (1 << 11); + break; + default: + /* I-cache aliases will be handled by D-cache aliasing code */ + aliasing_icache = 0; + } + + return aliasing_icache; +} + static void __init cacheid_init(void) { unsigned int cachetype = read_cpuid_cachetype(); @@ -249,10 +279,15 @@ static void __init cacheid_init(void) cacheid = CACHEID_VIPT_NONALIASING; if ((cachetype & (3 << 14)) == 1 << 14) cacheid |= CACHEID_ASID_TAGGED; - } else if (cachetype & (1 << 23)) + else if (cpu_has_aliasing_icache(CPU_ARCH_ARMv7)) + cacheid |= CACHEID_VIPT_I_ALIASING; + } else if (cachetype & (1 << 23)) { cacheid = CACHEID_VIPT_ALIASING; - else + } else { cacheid = CACHEID_VIPT_NONALIASING; + if (cpu_has_aliasing_icache(CPU_ARCH_ARMv6)) + cacheid |= CACHEID_VIPT_I_ALIASING; + } } else { cacheid = CACHEID_VIVT; } @@ -263,7 +298,7 @@ static void __init cacheid_init(void) cache_is_vipt_nonaliasing() ? "VIPT nonaliasing" : "unknown", cache_is_vivt() ? "VIVT" : icache_is_vivt_asid_tagged() ? "VIVT ASID tagged" : - cache_is_vipt_aliasing() ? "VIPT aliasing" : + icache_is_vipt_aliasing() ? "VIPT aliasing" : cache_is_vipt_nonaliasing() ? "VIPT nonaliasing" : "unknown"); } @@ -490,7 +525,7 @@ request_standard_resources(struct meminfo *mi, struct machine_desc *mdesc) kernel_code.start = virt_to_phys(_text); kernel_code.end = virt_to_phys(_etext - 1); - kernel_data.start = virt_to_phys(_data); + kernel_data.start = virt_to_phys(_sdata); kernel_data.end = virt_to_phys(_end - 1); for (i = 0; i < mi->nr_banks; i++) { @@ -825,7 +860,8 @@ void __init setup_arch(char **cmdline_p) request_standard_resources(&meminfo, mdesc); #ifdef CONFIG_SMP - smp_init_cpus(); + if (is_smp()) + smp_init_cpus(); #endif reserve_crashkernel(); diff --git a/arch/arm/kernel/smp.c b/arch/arm/kernel/smp.c index 40dc74f2b27f33..8c1959590252e7 100644 --- a/arch/arm/kernel/smp.c +++ b/arch/arm/kernel/smp.c @@ -33,6 +33,7 @@ #include #include #include +#include #include #include #include @@ -67,12 +68,47 @@ enum ipi_msg_type { IPI_CPU_STOP, }; +static inline void identity_mapping_add(pgd_t *pgd, unsigned long start, + unsigned long end) +{ + unsigned long addr, prot; + pmd_t *pmd; + + prot = PMD_TYPE_SECT | PMD_SECT_AP_WRITE; + if (cpu_architecture() <= CPU_ARCH_ARMv5TEJ && !cpu_is_xscale()) + prot |= PMD_BIT4; + + for (addr = start & PGDIR_MASK; addr < end;) { + pmd = pmd_offset(pgd + pgd_index(addr), addr); + pmd[0] = __pmd(addr | prot); + addr += SECTION_SIZE; + pmd[1] = __pmd(addr | prot); + addr += SECTION_SIZE; + flush_pmd_entry(pmd); + outer_clean_range(__pa(pmd), __pa(pmd + 1)); + } +} + +static inline void identity_mapping_del(pgd_t *pgd, unsigned long start, + unsigned long end) +{ + unsigned long addr; + pmd_t *pmd; + + for (addr = start & PGDIR_MASK; addr < end; addr += PGDIR_SIZE) { + pmd = pmd_offset(pgd + pgd_index(addr), addr); + pmd[0] = __pmd(0); + pmd[1] = __pmd(0); + clean_pmd_entry(pmd); + outer_clean_range(__pa(pmd), __pa(pmd + 1)); + } +} + int __cpuinit __cpu_up(unsigned int cpu) { struct cpuinfo_arm *ci = &per_cpu(cpu_data, cpu); struct task_struct *idle = ci->idle; pgd_t *pgd; - pmd_t *pmd; int ret; /* @@ -101,11 +137,16 @@ int __cpuinit __cpu_up(unsigned int cpu) * a 1:1 mapping for the physical address of the kernel. */ pgd = pgd_alloc(&init_mm); - pmd = pmd_offset(pgd + pgd_index(PHYS_OFFSET), PHYS_OFFSET); - *pmd = __pmd((PHYS_OFFSET & PGDIR_MASK) | - PMD_TYPE_SECT | PMD_SECT_AP_WRITE); - flush_pmd_entry(pmd); - outer_clean_range(__pa(pmd), __pa(pmd + 1)); + if (!pgd) + return -ENOMEM; + + if (PHYS_OFFSET != PAGE_OFFSET) { +#ifndef CONFIG_HOTPLUG_CPU + identity_mapping_add(pgd, __pa(__init_begin), __pa(__init_end)); +#endif + identity_mapping_add(pgd, __pa(_stext), __pa(_etext)); + identity_mapping_add(pgd, __pa(_sdata), __pa(_edata)); + } /* * We need to tell the secondary core where to find @@ -143,8 +184,14 @@ int __cpuinit __cpu_up(unsigned int cpu) secondary_data.stack = NULL; secondary_data.pgdir = 0; - *pmd = __pmd(0); - clean_pmd_entry(pmd); + if (PHYS_OFFSET != PAGE_OFFSET) { +#ifndef CONFIG_HOTPLUG_CPU + identity_mapping_del(pgd, __pa(__init_begin), __pa(__init_end)); +#endif + identity_mapping_del(pgd, __pa(_stext), __pa(_etext)); + identity_mapping_del(pgd, __pa(_sdata), __pa(_edata)); + } + pgd_free(&init_mm, pgd); if (ret) { @@ -567,7 +614,8 @@ void smp_send_stop(void) { cpumask_t mask = cpu_online_map; cpu_clear(smp_processor_id(), mask); - send_ipi_message(&mask, IPI_CPU_STOP); + if (!cpus_empty(mask)) + send_ipi_message(&mask, IPI_CPU_STOP); } /* diff --git a/arch/arm/kernel/unwind.c b/arch/arm/kernel/unwind.c index dd81a918c106ea..2a161765f6d5fd 100644 --- a/arch/arm/kernel/unwind.c +++ b/arch/arm/kernel/unwind.c @@ -146,6 +146,8 @@ static struct unwind_idx *unwind_find_idx(unsigned long addr) addr < table->end_addr) { idx = search_index(addr, table->start, table->stop - 1); + /* Move-to-front to exploit common traces */ + list_move(&table->list, &unwind_tables); break; } } diff --git a/arch/arm/kernel/vmlinux.lds.S b/arch/arm/kernel/vmlinux.lds.S index b16c07914b55bb..1953e3d21abf28 100644 --- a/arch/arm/kernel/vmlinux.lds.S +++ b/arch/arm/kernel/vmlinux.lds.S @@ -8,6 +8,19 @@ #include #include +#define PROC_INFO \ + VMLINUX_SYMBOL(__proc_info_begin) = .; \ + *(.proc.info.init) \ + VMLINUX_SYMBOL(__proc_info_end) = .; + +#ifdef CONFIG_HOTPLUG_CPU +#define ARM_CPU_DISCARD(x) +#define ARM_CPU_KEEP(x) x +#else +#define ARM_CPU_DISCARD(x) x +#define ARM_CPU_KEEP(x) +#endif + OUTPUT_ARCH(arm) ENTRY(stext) @@ -31,15 +44,18 @@ SECTIONS HEAD_TEXT INIT_TEXT _einittext = .; - __proc_info_begin = .; - *(.proc.info.init) - __proc_info_end = .; + ARM_CPU_DISCARD(PROC_INFO) __arch_info_begin = .; *(.arch.info.init) __arch_info_end = .; __tagtable_begin = .; *(.taglist.init) __tagtable_end = .; +#ifdef CONFIG_SMP_ON_UP + __smpalt_begin = .; + *(.alt.smp.init) + __smpalt_end = .; +#endif INIT_SETUP(16) @@ -68,10 +84,8 @@ SECTIONS /DISCARD/ : { *(.ARM.exidx.exit.text) *(.ARM.extab.exit.text) -#ifndef CONFIG_HOTPLUG_CPU - *(.ARM.exidx.cpuexit.text) - *(.ARM.extab.cpuexit.text) -#endif + ARM_CPU_DISCARD(*(.ARM.exidx.cpuexit.text)) + ARM_CPU_DISCARD(*(.ARM.extab.cpuexit.text)) #ifndef CONFIG_HOTPLUG *(.ARM.exidx.devexit.text) *(.ARM.extab.devexit.text) @@ -100,12 +114,11 @@ SECTIONS *(.glue_7) *(.glue_7t) *(.got) /* Global offset table */ + ARM_CPU_KEEP(PROC_INFO) } RO_DATA(PAGE_SIZE) - _etext = .; /* End of text and rodata section */ - #ifdef CONFIG_ARM_UNWIND /* * Stack unwinding tables @@ -123,6 +136,8 @@ SECTIONS } #endif + _etext = .; /* End of text and rodata section */ + #ifdef CONFIG_XIP_KERNEL __data_loc = ALIGN(4); /* location in binary */ . = PAGE_OFFSET + TEXT_OFFSET; @@ -237,6 +252,12 @@ SECTIONS /* Default discards */ DISCARDS + +#ifndef CONFIG_SMP_ON_UP + /DISCARD/ : { + *(.alt.smp.init) + } +#endif } /* diff --git a/arch/arm/mach-aaec2000/aaed2000.c b/arch/arm/mach-aaec2000/aaed2000.c index 81a3ecc0d104d0..0eb3e3e5b2d115 100644 --- a/arch/arm/mach-aaec2000/aaed2000.c +++ b/arch/arm/mach-aaec2000/aaed2000.c @@ -95,8 +95,6 @@ static void __init aaed2000_map_io(void) MACHINE_START(AAED2000, "Agilent AAED-2000 Development Platform") /* Maintainer: Nicolas Bellido Y Ortega */ - .phys_io = PIO_BASE, - .io_pg_offst = ((VIO_BASE) >> 18) & 0xfffc, .map_io = aaed2000_map_io, .init_irq = aaed2000_init_irq, .timer = &aaec2000_timer, diff --git a/arch/arm/mach-aaec2000/include/mach/debug-macro.S b/arch/arm/mach-aaec2000/include/mach/debug-macro.S index a9cac368bfe69f..bc7ad5561c4cae 100644 --- a/arch/arm/mach-aaec2000/include/mach/debug-macro.S +++ b/arch/arm/mach-aaec2000/include/mach/debug-macro.S @@ -10,12 +10,10 @@ */ #include "hardware.h" - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - moveq \rx, #0x80000000 @ physical - movne \rx, #io_p2v(0x80000000) @ virtual - orr \rx, \rx, #0x00000800 + .macro addruart, rp, rv + mov \rp, 0x00000800 + orr \rv, \rp, #io_p2v(0x80000000) @ virtual + orr \rp, \rp, #0x80000000 @ physical .endm .macro senduart,rd,rx diff --git a/arch/arm/mach-aaec2000/include/mach/vmalloc.h b/arch/arm/mach-aaec2000/include/mach/vmalloc.h index 551f68f666bf02..cff4e0a996ce99 100644 --- a/arch/arm/mach-aaec2000/include/mach/vmalloc.h +++ b/arch/arm/mach-aaec2000/include/mach/vmalloc.h @@ -11,6 +11,6 @@ #ifndef __ASM_ARCH_VMALLOC_H #define __ASM_ARCH_VMALLOC_H -#define VMALLOC_END (PAGE_OFFSET + 0x10000000) +#define VMALLOC_END 0xd0000000 #endif /* __ASM_ARCH_VMALLOC_H */ diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 939bccd7056984..851e8139ef9d1a 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -33,6 +33,7 @@ config ARCH_AT91SAM9260 select HAVE_AT91_USART3 select HAVE_AT91_USART4 select HAVE_AT91_USART5 + select HAVE_NET_MACB config ARCH_AT91SAM9261 bool "AT91SAM9261" @@ -51,6 +52,7 @@ config ARCH_AT91SAM9263 select CPU_ARM926T select GENERIC_CLOCKEVENTS select HAVE_FB_ATMEL + select HAVE_NET_MACB config ARCH_AT91SAM9RL bool "AT91SAM9RL" @@ -66,6 +68,7 @@ config ARCH_AT91SAM9G20 select HAVE_AT91_USART3 select HAVE_AT91_USART4 select HAVE_AT91_USART5 + select HAVE_NET_MACB config ARCH_AT91SAM9G45 bool "AT91SAM9G45" @@ -73,6 +76,7 @@ config ARCH_AT91SAM9G45 select GENERIC_CLOCKEVENTS select HAVE_AT91_USART3 select HAVE_FB_ATMEL + select HAVE_NET_MACB config ARCH_AT91CAP9 bool "AT91CAP9" @@ -248,6 +252,12 @@ config MACH_CPU9260 Select this if you are using a Eukrea Electromatique's CPU9260 Board +config MACH_FLEXIBITY + bool "Flexibity Connect board" + help + Select this if you are using Flexibity Connect board + + endif # ---------------------------------------------------------- @@ -338,6 +348,7 @@ config MACH_AT91SAM9G20EK that embeds only one SD/MMC slot. config MACH_AT91SAM9G20EK_2MMC + depends on MACH_AT91SAM9G20EK bool "Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots" select HAVE_NAND_ATMEL_BUSWIDTH_16 help @@ -383,8 +394,8 @@ if ARCH_AT91SAM9G45 comment "AT91SAM9G45 Board Type" -config MACH_AT91SAM9G45EKES - bool "Atmel AT91SAM9G45-EKES Evaluation Kit" +config MACH_AT91SAM9M10G45EK + bool "Atmel AT91SAM9M10G45-EK Evaluation Kits" select HAVE_NAND_ATMEL_BUSWIDTH_16 help Select this if you are using Atmel's AT91SAM9G45-EKES Evaluation Kit. diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index ca2ac003f41f56..412b3a471a4b43 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -46,6 +46,7 @@ obj-$(CONFIG_MACH_USB_A9260) += board-usb-a9260.o obj-$(CONFIG_MACH_QIL_A9260) += board-qil-a9260.o obj-$(CONFIG_MACH_AFEB9260) += board-afeb-9260v1.o obj-$(CONFIG_MACH_CPU9260) += board-cpu9krea.o +obj-$(CONFIG_MACH_FLEXIBITY) += board-flexibity.o # AT91SAM9261 board-specific support obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o @@ -61,7 +62,6 @@ obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o # AT91SAM9G20 board-specific support obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o -obj-$(CONFIG_MACH_AT91SAM9G20EK_2MMC) += board-sam9g20ek-2slot-mmc.o obj-$(CONFIG_MACH_CPU9G20) += board-cpu9krea.o obj-$(CONFIG_MACH_STAMP9G20) += board-stamp9g20.o obj-$(CONFIG_MACH_PORTUXG20) += board-stamp9g20.o @@ -70,7 +70,7 @@ obj-$(CONFIG_MACH_PORTUXG20) += board-stamp9g20.o obj-$(CONFIG_MACH_SNAPPER_9260) += board-snapper9260.o # AT91SAM9G45 board-specific support -obj-$(CONFIG_MACH_AT91SAM9G45EKES) += board-sam9m10g45ek.o +obj-$(CONFIG_MACH_AT91SAM9M10G45EK) += board-sam9m10g45ek.o # AT91CAP9 board-specific support obj-$(CONFIG_MACH_AT91CAP9ADK) += board-cap9adk.o diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c index 9b27d167bff0c0..46bdc82d3fbf99 100644 --- a/arch/arm/mach-at91/board-1arm.c +++ b/arch/arm/mach-at91/board-1arm.c @@ -92,8 +92,6 @@ static void __init onearm_board_init(void) MACHINE_START(ONEARM, "Ajeco 1ARM single board computer") /* Maintainer: Lennert Buytenhek */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91rm9200_timer, .map_io = onearm_map_io, diff --git a/arch/arm/mach-at91/board-afeb-9260v1.c b/arch/arm/mach-at91/board-afeb-9260v1.c index 50667bed7cc9f7..cba7f7771feed1 100644 --- a/arch/arm/mach-at91/board-afeb-9260v1.c +++ b/arch/arm/mach-at91/board-afeb-9260v1.c @@ -218,8 +218,6 @@ static void __init afeb9260_board_init(void) MACHINE_START(AFEB9260, "Custom afeb9260 board") /* Maintainer: Sergey Lapin */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = afeb9260_map_io, diff --git a/arch/arm/mach-at91/board-at572d940hf_ek.c b/arch/arm/mach-at91/board-at572d940hf_ek.c index 5daff277f53e0d..3929f1c9e4e5ce 100644 --- a/arch/arm/mach-at91/board-at572d940hf_ek.c +++ b/arch/arm/mach-at91/board-at572d940hf_ek.c @@ -216,7 +216,7 @@ static struct atmel_nand_data __initdata eb_nand_data = { /* .rdy_pin = AT91_PIN_PC16, */ .enable_pin = AT91_PIN_PA15, .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) +#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) .bus_width_16 = 1, #else .bus_width_16 = 0, @@ -318,8 +318,6 @@ static void __init eb_board_init(void) MACHINE_START(AT572D940HFEB, "Atmel AT91D940HF-EB") /* Maintainer: Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = eb_map_io, diff --git a/arch/arm/mach-at91/board-cam60.c b/arch/arm/mach-at91/board-cam60.c index 44eb9f76493898..b54e3e6fceb677 100644 --- a/arch/arm/mach-at91/board-cam60.c +++ b/arch/arm/mach-at91/board-cam60.c @@ -198,8 +198,6 @@ static void __init cam60_board_init(void) MACHINE_START(CAM60, "KwikByte CAM60") /* Maintainer: KwikByte */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = cam60_map_io, diff --git a/arch/arm/mach-at91/board-cap9adk.c b/arch/arm/mach-at91/board-cap9adk.c index d6940870e403fb..e7274440ead99f 100644 --- a/arch/arm/mach-at91/board-cap9adk.c +++ b/arch/arm/mach-at91/board-cap9adk.c @@ -399,8 +399,6 @@ static void __init cap9adk_board_init(void) MACHINE_START(AT91CAP9ADK, "Atmel AT91CAP9A-DK") /* Maintainer: Stelian Pop */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = cap9adk_map_io, diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c index db1f9544d2e0f9..2e74a19874d11a 100644 --- a/arch/arm/mach-at91/board-carmeva.c +++ b/arch/arm/mach-at91/board-carmeva.c @@ -162,8 +162,6 @@ static void __init carmeva_board_init(void) MACHINE_START(CARMEVA, "Carmeva") /* Maintainer: Conitec Datasystems */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91rm9200_timer, .map_io = carmeva_map_io, diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c index 4bc2e9f6ebb537..3838594578f353 100644 --- a/arch/arm/mach-at91/board-cpu9krea.c +++ b/arch/arm/mach-at91/board-cpu9krea.c @@ -375,8 +375,6 @@ MACHINE_START(CPUAT9260, "Eukrea CPU9260") MACHINE_START(CPUAT9G20, "Eukrea CPU9G20") #endif /* Maintainer: Eric Benard - EUKREA Electromatique */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = cpu9krea_map_io, diff --git a/arch/arm/mach-at91/board-cpuat91.c b/arch/arm/mach-at91/board-cpuat91.c index a28d99656190e2..2f4dd8cdd484a5 100644 --- a/arch/arm/mach-at91/board-cpuat91.c +++ b/arch/arm/mach-at91/board-cpuat91.c @@ -175,8 +175,6 @@ static void __init cpuat91_board_init(void) MACHINE_START(CPUAT91, "Eukrea") /* Maintainer: Eric Benard - EUKREA Electromatique */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91rm9200_timer, .map_io = cpuat91_map_io, diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c index fea2529ebcf9c7..464839dc39bd4d 100644 --- a/arch/arm/mach-at91/board-csb337.c +++ b/arch/arm/mach-at91/board-csb337.c @@ -257,8 +257,6 @@ static void __init csb337_board_init(void) MACHINE_START(CSB337, "Cogent CSB337") /* Maintainer: Bill Gatliff */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91rm9200_timer, .map_io = csb337_map_io, diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c index cfa3f04b22053e..431688c6141267 100644 --- a/arch/arm/mach-at91/board-csb637.c +++ b/arch/arm/mach-at91/board-csb637.c @@ -138,8 +138,6 @@ static void __init csb637_board_init(void) MACHINE_START(CSB637, "Cogent CSB637") /* Maintainer: Bill Gatliff */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91rm9200_timer, .map_io = csb637_map_io, diff --git a/arch/arm/mach-at91/board-dk.c b/arch/arm/mach-at91/board-dk.c index 0fd0f5bc77ea56..e14f0e165680ed 100644 --- a/arch/arm/mach-at91/board-dk.c +++ b/arch/arm/mach-at91/board-dk.c @@ -225,8 +225,6 @@ static void __init dk_board_init(void) MACHINE_START(AT91RM9200DK, "Atmel AT91RM9200-DK") /* Maintainer: SAN People/Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91rm9200_timer, .map_io = dk_map_io, diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c index 528656761ff74d..6cf6566ae34661 100644 --- a/arch/arm/mach-at91/board-eb9200.c +++ b/arch/arm/mach-at91/board-eb9200.c @@ -120,8 +120,6 @@ static void __init eb9200_board_init(void) } MACHINE_START(ATEB9200, "Embest ATEB9200") - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91rm9200_timer, .map_io = eb9200_map_io, diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c index 1d69908617f07c..7b58c948a957e8 100644 --- a/arch/arm/mach-at91/board-ecbat91.c +++ b/arch/arm/mach-at91/board-ecbat91.c @@ -168,8 +168,6 @@ static void __init ecb_at91board_init(void) MACHINE_START(ECBAT91, "emQbit's ECB_AT91") /* Maintainer: emQbit.com */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91rm9200_timer, .map_io = ecb_at91map_io, diff --git a/arch/arm/mach-at91/board-eco920.c b/arch/arm/mach-at91/board-eco920.c index 295a96609e7175..a158a0ce458fb3 100644 --- a/arch/arm/mach-at91/board-eco920.c +++ b/arch/arm/mach-at91/board-eco920.c @@ -148,8 +148,6 @@ static void __init eco920_board_init(void) MACHINE_START(ECO920, "eco920") /* Maintainer: Sascha Hauer */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91rm9200_timer, .map_io = eco920_map_io, diff --git a/arch/arm/mach-at91/board-ek.c b/arch/arm/mach-at91/board-ek.c index 4cdfaac8e590fe..56e92c4bbc2a32 100644 --- a/arch/arm/mach-at91/board-ek.c +++ b/arch/arm/mach-at91/board-ek.c @@ -191,8 +191,6 @@ static void __init ek_board_init(void) MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK") /* Maintainer: SAN People/Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91rm9200_timer, .map_io = ek_map_io, diff --git a/arch/arm/mach-at91/board-flexibity.c b/arch/arm/mach-at91/board-flexibity.c new file mode 100644 index 00000000000000..c8a62dc8fa6596 --- /dev/null +++ b/arch/arm/mach-at91/board-flexibity.c @@ -0,0 +1,162 @@ +/* + * linux/arch/arm/mach-at91/board-flexibity.c + * + * Copyright (C) 2010 Flexibity + * Copyright (C) 2005 SAN People + * Copyright (C) 2006 Atmel + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include + +#include + +#include +#include +#include + +#include +#include + +#include "generic.h" + +static void __init flexibity_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91sam9260_initialize(18432000); + + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); +} + +static void __init flexibity_init_irq(void) +{ + at91sam9260_init_interrupts(NULL); +} + +/* USB Host port */ +static struct at91_usbh_data __initdata flexibity_usbh_data = { + .ports = 2, +}; + +/* USB Device port */ +static struct at91_udc_data __initdata flexibity_udc_data = { + .vbus_pin = AT91_PIN_PC5, + .pullup_pin = 0, /* pull-up driven by UDC */ +}; + +/* SPI devices */ +static struct spi_board_info flexibity_spi_devices[] = { + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 1, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +}; + +/* MCI (SD/MMC) */ +static struct at91_mmc_data __initdata flexibity_mmc_data = { + .slot_b = 0, + .wire4 = 1, + .det_pin = AT91_PIN_PC9, + .wp_pin = AT91_PIN_PC4, +}; + +/* LEDs */ +static struct gpio_led flexibity_leds[] = { + { + .name = "usb1:green", + .gpio = AT91_PIN_PA12, + .active_low = 1, + .default_trigger = "default-on", + }, + { + .name = "usb1:red", + .gpio = AT91_PIN_PA13, + .active_low = 1, + .default_trigger = "default-on", + }, + { + .name = "usb2:green", + .gpio = AT91_PIN_PB26, + .active_low = 1, + .default_trigger = "default-on", + }, + { + .name = "usb2:red", + .gpio = AT91_PIN_PB27, + .active_low = 1, + .default_trigger = "default-on", + }, + { + .name = "usb3:green", + .gpio = AT91_PIN_PC8, + .active_low = 1, + .default_trigger = "default-on", + }, + { + .name = "usb3:red", + .gpio = AT91_PIN_PC6, + .active_low = 1, + .default_trigger = "default-on", + }, + { + .name = "usb4:green", + .gpio = AT91_PIN_PB4, + .active_low = 1, + .default_trigger = "default-on", + }, + { + .name = "usb4:red", + .gpio = AT91_PIN_PB5, + .active_low = 1, + .default_trigger = "default-on", + } +}; + +static void __init flexibity_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&flexibity_usbh_data); + /* USB Device */ + at91_add_device_udc(&flexibity_udc_data); + /* SPI */ + at91_add_device_spi(flexibity_spi_devices, + ARRAY_SIZE(flexibity_spi_devices)); + /* MMC */ + at91_add_device_mmc(0, &flexibity_mmc_data); + /* LEDs */ + at91_gpio_leds(flexibity_leds, ARRAY_SIZE(flexibity_leds)); +} + +MACHINE_START(FLEXIBITY, "Flexibity Connect") + /* Maintainer: Maxim Osipov */ + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = flexibity_map_io, + .init_irq = flexibity_init_irq, + .init_machine = flexibity_board_init, +MACHINE_END diff --git a/arch/arm/mach-at91/board-kafa.c b/arch/arm/mach-at91/board-kafa.c index a87956c0a74f32..c0ce79d431a0c1 100644 --- a/arch/arm/mach-at91/board-kafa.c +++ b/arch/arm/mach-at91/board-kafa.c @@ -99,8 +99,6 @@ static void __init kafa_board_init(void) MACHINE_START(KAFA, "Sperry-Sun KAFA") /* Maintainer: Sergei Sharonov */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91rm9200_timer, .map_io = kafa_map_io, diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c index fe9b9913fa3cd9..a13d2063faff8e 100644 --- a/arch/arm/mach-at91/board-kb9202.c +++ b/arch/arm/mach-at91/board-kb9202.c @@ -136,8 +136,6 @@ static void __init kb9202_board_init(void) MACHINE_START(KB9200, "KB920x") /* Maintainer: KwikByte, Inc. */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91rm9200_timer, .map_io = kb9202_map_io, diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c index 7c1e382330fb61..fe5f1d47e6e238 100644 --- a/arch/arm/mach-at91/board-neocore926.c +++ b/arch/arm/mach-at91/board-neocore926.c @@ -387,8 +387,6 @@ static void __init neocore926_board_init(void) MACHINE_START(NEOCORE926, "ADENEO NEOCORE 926") /* Maintainer: ADENEO */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = neocore926_map_io, diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c index 859727e7ea301a..9d833bbc592dcf 100644 --- a/arch/arm/mach-at91/board-picotux200.c +++ b/arch/arm/mach-at91/board-picotux200.c @@ -156,8 +156,6 @@ static void __init picotux200_board_init(void) MACHINE_START(PICOTUX2XX, "picotux 200") /* Maintainer: Kleinhenz Elektronik GmbH */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91rm9200_timer, .map_io = picotux200_map_io, diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c index 664938e8f66118..69d15a875b667f 100644 --- a/arch/arm/mach-at91/board-qil-a9260.c +++ b/arch/arm/mach-at91/board-qil-a9260.c @@ -268,8 +268,6 @@ static void __init ek_board_init(void) MACHINE_START(QIL_A9260, "CALAO QIL_A9260") /* Maintainer: calao-systems */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = ek_map_io, diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c index b4834697753499..25a26beaa728bb 100644 --- a/arch/arm/mach-at91/board-sam9-l9260.c +++ b/arch/arm/mach-at91/board-sam9-l9260.c @@ -212,8 +212,6 @@ static void __init ek_board_init(void) MACHINE_START(SAM9_L9260, "Olimex SAM9-L9260") /* Maintainer: Olimex */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = ek_map_io, diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c index ba9d501b5c50a8..de1816e0e1d967 100644 --- a/arch/arm/mach-at91/board-sam9260ek.c +++ b/arch/arm/mach-at91/board-sam9260ek.c @@ -356,8 +356,6 @@ static void __init ek_board_init(void) MACHINE_START(AT91SAM9260EK, "Atmel AT91SAM9260-EK") /* Maintainer: Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = ek_map_io, diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c index 65eb0943194f4b..14acc901e24cdd 100644 --- a/arch/arm/mach-at91/board-sam9261ek.c +++ b/arch/arm/mach-at91/board-sam9261ek.c @@ -623,8 +623,6 @@ MACHINE_START(AT91SAM9261EK, "Atmel AT91SAM9261-EK") MACHINE_START(AT91SAM9G10EK, "Atmel AT91SAM9G10-EK") #endif /* Maintainer: Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = ek_map_io, diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c index 2d867fb0630f07..bfe490df58be9e 100644 --- a/arch/arm/mach-at91/board-sam9263ek.c +++ b/arch/arm/mach-at91/board-sam9263ek.c @@ -454,8 +454,6 @@ static void __init ek_board_init(void) MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK") /* Maintainer: Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = ek_map_io, diff --git a/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c b/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c deleted file mode 100644 index c49f5c003ee10d..00000000000000 --- a/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c +++ /dev/null @@ -1,329 +0,0 @@ -/* - * Copyright (C) 2005 SAN People - * Copyright (C) 2008 Atmel - * Copyright (C) 2009 Rob Emanuele - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include "sam9_smc.h" -#include "generic.h" - - -static void __init ek_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91sam9260_initialize(18432000); - - /* DGBU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); -} - -static void __init ek_init_irq(void) -{ - at91sam9260_init_interrupts(NULL); -} - - -/* - * USB Host port - */ -static struct at91_usbh_data __initdata ek_usbh_data = { - .ports = 2, -}; - -/* - * USB Device port - */ -static struct at91_udc_data __initdata ek_udc_data = { - .vbus_pin = AT91_PIN_PC5, - .pullup_pin = 0, /* pull-up driven by UDC */ -}; - - -/* - * SPI devices. - */ -static struct spi_board_info ek_spi_devices[] = { -#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91)) - { /* DataFlash chip */ - .modalias = "mtd_dataflash", - .chip_select = 1, - .max_speed_hz = 15 * 1000 * 1000, - .bus_num = 0, - }, -#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) - { /* DataFlash card */ - .modalias = "mtd_dataflash", - .chip_select = 0, - .max_speed_hz = 15 * 1000 * 1000, - .bus_num = 0, - }, -#endif -#endif -}; - - -/* - * MACB Ethernet device - */ -static struct at91_eth_data __initdata ek_macb_data = { - .phy_irq_pin = AT91_PIN_PB0, - .is_rmii = 1, -}; - - -/* - * NAND flash - */ -static struct mtd_partition __initdata ek_nand_partition[] = { - { - .name = "Bootstrap", - .offset = 0, - .size = 4 * SZ_1M, - }, - { - .name = "Partition 1", - .offset = MTDPART_OFS_NXTBLK, - .size = 60 * SZ_1M, - }, - { - .name = "Partition 2", - .offset = MTDPART_OFS_NXTBLK, - .size = MTDPART_SIZ_FULL, - }, -}; - -static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) -{ - *num_partitions = ARRAY_SIZE(ek_nand_partition); - return ek_nand_partition; -} - -/* det_pin is not connected */ -static struct atmel_nand_data __initdata ek_nand_data = { - .ale = 21, - .cle = 22, - .rdy_pin = AT91_PIN_PC13, - .enable_pin = AT91_PIN_PC14, - .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) - .bus_width_16 = 1, -#else - .bus_width_16 = 0, -#endif -}; - -static struct sam9_smc_config __initdata ek_nand_smc_config = { - .ncs_read_setup = 0, - .nrd_setup = 2, - .ncs_write_setup = 0, - .nwe_setup = 2, - - .ncs_read_pulse = 4, - .nrd_pulse = 4, - .ncs_write_pulse = 4, - .nwe_pulse = 4, - - .read_cycle = 7, - .write_cycle = 7, - - .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE, - .tdf_cycles = 3, -}; - -static void __init ek_add_device_nand(void) -{ - /* setup bus-width (8 or 16) */ - if (ek_nand_data.bus_width_16) - ek_nand_smc_config.mode |= AT91_SMC_DBW_16; - else - ek_nand_smc_config.mode |= AT91_SMC_DBW_8; - - /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &ek_nand_smc_config); - - at91_add_device_nand(&ek_nand_data); -} - - -/* - * MCI (SD/MMC) - * wp_pin is not connected - */ -#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) -static struct mci_platform_data __initdata ek_mmc_data = { - .slot[0] = { - .bus_width = 4, - .detect_pin = AT91_PIN_PC2, - .wp_pin = -ENODEV, - }, - .slot[1] = { - .bus_width = 4, - .detect_pin = AT91_PIN_PC9, - .wp_pin = -ENODEV, - }, - -}; -#else -static struct at91_mmc_data __initdata ek_mmc_data = { - .slot_b = 1, /* Only one slot so use slot B */ - .wire4 = 1, - .det_pin = AT91_PIN_PC9, -}; -#endif - -/* - * LEDs - */ -static struct gpio_led ek_leds[] = { - { /* "bottom" led, green, userled1 to be defined */ - .name = "ds5", - .gpio = AT91_PIN_PB8, - .active_low = 1, - .default_trigger = "none", - }, - { /* "power" led, yellow */ - .name = "ds1", - .gpio = AT91_PIN_PB9, - .default_trigger = "heartbeat", - } -}; - -#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE) -static struct regulator_consumer_supply ek_audio_consumer_supplies[] = { - REGULATOR_SUPPLY("AVDD", "0-001b"), - REGULATOR_SUPPLY("HPVDD", "0-001b"), - REGULATOR_SUPPLY("DBVDD", "0-001b"), - REGULATOR_SUPPLY("DCVDD", "0-001b"), -}; - -static struct regulator_init_data ek_avdd_reg_init_data = { - .constraints = { - .name = "3V3", - .valid_ops_mask = REGULATOR_CHANGE_STATUS, - }, - .consumer_supplies = ek_audio_consumer_supplies, - .num_consumer_supplies = ARRAY_SIZE(ek_audio_consumer_supplies), -}; - -static struct fixed_voltage_config ek_vdd_pdata = { - .supply_name = "board-3V3", - .microvolts = 3300000, - .gpio = -EINVAL, - .enabled_at_boot = 0, - .init_data = &ek_avdd_reg_init_data, -}; -static struct platform_device ek_voltage_regulator = { - .name = "reg-fixed-voltage", - .id = -1, - .num_resources = 0, - .dev = { - .platform_data = &ek_vdd_pdata, - }, -}; -static void __init ek_add_regulators(void) -{ - platform_device_register(&ek_voltage_regulator); -} -#else -static void __init ek_add_regulators(void) {} -#endif - -static struct i2c_board_info __initdata ek_i2c_devices[] = { - { - I2C_BOARD_INFO("24c512", 0x50), - }, -}; - - -static void __init ek_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* USB Host */ - at91_add_device_usbh(&ek_usbh_data); - /* USB Device */ - at91_add_device_udc(&ek_udc_data); - /* SPI */ - at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); - /* NAND */ - ek_add_device_nand(); - /* Ethernet */ - at91_add_device_eth(&ek_macb_data); - /* Regulators */ - ek_add_regulators(); - /* MMC */ -#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) - at91_add_device_mci(0, &ek_mmc_data); -#else - at91_add_device_mmc(0, &ek_mmc_data); -#endif - /* I2C */ - at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); - /* LEDs */ - at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); - /* PCK0 provides MCLK to the WM8731 */ - at91_set_B_periph(AT91_PIN_PC1, 0); - /* SSC (for WM8731) */ - at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX); -} - -MACHINE_START(AT91SAM9G20EK_2MMC, "Atmel AT91SAM9G20-EK 2 MMC Slot Mod") - /* Maintainer: Rob Emanuele */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91sam926x_timer, - .map_io = ek_map_io, - .init_irq = ek_init_irq, - .init_machine = ek_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c index 6ea9808b8868d5..ca8198b3c168bb 100644 --- a/arch/arm/mach-at91/board-sam9g20ek.c +++ b/arch/arm/mach-at91/board-sam9g20ek.c @@ -47,6 +47,18 @@ #include "sam9_smc.h" #include "generic.h" +/* + * board revision encoding + * bit 0: + * 0 => 1 sd/mmc slot + * 1 => 2 sd/mmc slots connectors (board from revision C) + */ +#define HAVE_2MMC (1 << 0) +static int inline ek_have_2mmc(void) +{ + return machine_is_at91sam9g20ek_2mmc() || (system_rev & HAVE_2MMC); +} + static void __init ek_map_io(void) { @@ -94,7 +106,7 @@ static struct at91_udc_data __initdata ek_udc_data = { * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91)) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, @@ -121,6 +133,13 @@ static struct at91_eth_data __initdata ek_macb_data = { .is_rmii = 1, }; +static void __init ek_add_device_macb(void) +{ + if (ek_have_2mmc()) + ek_macb_data.phy_irq_pin = AT91_PIN_PB0; + + at91_add_device_eth(&ek_macb_data); +} /* * NAND flash @@ -198,13 +217,36 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) - * det_pin, wp_pin and vcc_pin are not connected + * wp_pin and vcc_pin are not connected */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ek_mmc_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC9, + }, + +}; +#else static struct at91_mmc_data __initdata ek_mmc_data = { - .slot_b = 1, + .slot_b = 1, /* Only one slot so use slot B */ .wire4 = 1, + .det_pin = AT91_PIN_PC9, }; +#endif +static void __init ek_add_device_mmc(void) +{ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + if (ek_have_2mmc()) { + ek_mmc_data.slot[0].bus_width = 4; + ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2; + } + at91_add_device_mci(0, &ek_mmc_data); +#else + at91_add_device_mmc(0, &ek_mmc_data); +#endif +} /* * LEDs @@ -223,6 +265,15 @@ static struct gpio_led ek_leds[] = { } }; +static void __init ek_add_device_gpio_leds(void) +{ + if (ek_have_2mmc()) { + ek_leds[0].gpio = AT91_PIN_PB8; + ek_leds[1].gpio = AT91_PIN_PB9; + } + + at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); +} /* * GPIO Buttons @@ -336,15 +387,15 @@ static void __init ek_board_init(void) /* NAND */ ek_add_device_nand(); /* Ethernet */ - at91_add_device_eth(&ek_macb_data); + ek_add_device_macb(); /* Regulators */ ek_add_regulators(); /* MMC */ - at91_add_device_mmc(0, &ek_mmc_data); + ek_add_device_mmc(); /* I2C */ at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); /* LEDs */ - at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); + ek_add_device_gpio_leds(); /* Push Buttons */ ek_add_device_buttons(); /* PCK0 provides MCLK to the WM8731 */ @@ -355,8 +406,15 @@ static void __init ek_board_init(void) MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK") /* Maintainer: Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END + +MACHINE_START(AT91SAM9G20EK_2MMC, "Atmel AT91SAM9G20-EK 2 MMC Slot Mod") + /* Maintainer: Atmel */ .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = ek_map_io, diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c index ee800595594d3f..7913984f6de9bb 100644 --- a/arch/arm/mach-at91/board-sam9m10g45ek.c +++ b/arch/arm/mach-at91/board-sam9m10g45ek.c @@ -135,7 +135,7 @@ static struct atmel_nand_data __initdata ek_nand_data = { .rdy_pin = AT91_PIN_PC8, .enable_pin = AT91_PIN_PC14, .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) +#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) .bus_width_16 = 1, #else .bus_width_16 = 0, @@ -399,10 +399,8 @@ static void __init ek_board_init(void) at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led)); } -MACHINE_START(AT91SAM9G45EKES, "Atmel AT91SAM9G45-EKES") +MACHINE_START(AT91SAM9M10G45EK, "Atmel AT91SAM9M10G45-EK") /* Maintainer: Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = ek_map_io, diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c index 7ac20f3a2067d6..3bf3408e94c18f 100644 --- a/arch/arm/mach-at91/board-sam9rlek.c +++ b/arch/arm/mach-at91/board-sam9rlek.c @@ -329,8 +329,6 @@ static void __init ek_board_init(void) MACHINE_START(AT91SAM9RLEK, "Atmel AT91SAM9RL-EK") /* Maintainer: Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = ek_map_io, diff --git a/arch/arm/mach-at91/board-snapper9260.c b/arch/arm/mach-at91/board-snapper9260.c index 2c08ae4ad3a137..0a99b3cedd7a43 100644 --- a/arch/arm/mach-at91/board-snapper9260.c +++ b/arch/arm/mach-at91/board-snapper9260.c @@ -177,8 +177,6 @@ static void __init snapper9260_board_init(void) } MACHINE_START(SNAPPER_9260, "Bluewater Systems Snapper 9260/9G20 module") - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = snapper9260_map_io, diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c index 87958274290f35..5206eef4a67eba 100644 --- a/arch/arm/mach-at91/board-stamp9g20.c +++ b/arch/arm/mach-at91/board-stamp9g20.c @@ -294,8 +294,6 @@ static void __init stamp9g20_board_init(void) MACHINE_START(PORTUXG20, "taskit PortuxG20") /* Maintainer: taskit GmbH */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = portuxg20_map_io, @@ -305,8 +303,6 @@ MACHINE_END MACHINE_START(STAMP9G20, "taskit Stamp9G20") /* Maintainer: taskit GmbH */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = stamp9g20_map_io, diff --git a/arch/arm/mach-at91/board-usb-a9260.c b/arch/arm/mach-at91/board-usb-a9260.c index 905d6ef768078d..07784baeae841f 100644 --- a/arch/arm/mach-at91/board-usb-a9260.c +++ b/arch/arm/mach-at91/board-usb-a9260.c @@ -228,8 +228,6 @@ static void __init ek_board_init(void) MACHINE_START(USB_A9260, "CALAO USB_A9260") /* Maintainer: calao-systems */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = ek_map_io, diff --git a/arch/arm/mach-at91/board-usb-a9263.c b/arch/arm/mach-at91/board-usb-a9263.c index b6a3480383e58b..b614508931fd92 100644 --- a/arch/arm/mach-at91/board-usb-a9263.c +++ b/arch/arm/mach-at91/board-usb-a9263.c @@ -244,8 +244,6 @@ static void __init ek_board_init(void) MACHINE_START(USB_A9263, "CALAO USB_A9263") /* Maintainer: calao-systems */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = ek_map_io, diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c index e22bf051f835a1..89df00a9d2f72b 100644 --- a/arch/arm/mach-at91/board-yl-9200.c +++ b/arch/arm/mach-at91/board-yl-9200.c @@ -594,8 +594,6 @@ static void __init yl9200_board_init(void) MACHINE_START(YL9200, "uCdragon YL-9200") /* Maintainer: S.Birtles */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91rm9200_timer, .map_io = yl9200_map_io, diff --git a/arch/arm/mach-at91/include/mach/at91x40.h b/arch/arm/mach-at91/include/mach/at91x40.h index d34cdb8abdca65..063ac44a020423 100644 --- a/arch/arm/mach-at91/include/mach/at91x40.h +++ b/arch/arm/mach-at91/include/mach/at91x40.h @@ -52,4 +52,10 @@ #define AT91_DBGU_CIDR (AT91_SF + 0) /* CIDR in PS segment */ #define AT91_DBGU_EXID (AT91_SF + 4) /* EXID in PS segment */ +/* + * Support defines for the simple Power Controller module. + */ +#define AT91_PS_CR (AT91_PS + 0) /* PS Control register */ +#define AT91_PS_CR_CPU (1 << 0) /* CPU clock disable bit */ + #endif /* AT91X40_H */ diff --git a/arch/arm/mach-at91/include/mach/debug-macro.S b/arch/arm/mach-at91/include/mach/debug-macro.S index 9e750a1c1b5a80..0f959faf74a9ff 100644 --- a/arch/arm/mach-at91/include/mach/debug-macro.S +++ b/arch/arm/mach-at91/include/mach/debug-macro.S @@ -14,11 +14,9 @@ #include #include - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - ldreq \rx, =(AT91_BASE_SYS + AT91_DBGU) @ System peripherals (phys address) - ldrne \rx, =(AT91_VA_BASE_SYS + AT91_DBGU) @ System peripherals (virt address) + .macro addruart, rp, rv + ldr \rp, =(AT91_BASE_SYS + AT91_DBGU) @ System peripherals (phys address) + ldr \rv, =(AT91_VA_BASE_SYS + AT91_DBGU) @ System peripherals (virt address) .endm .macro senduart,rd,rx diff --git a/arch/arm/mach-at91/include/mach/system.h b/arch/arm/mach-at91/include/mach/system.h index ee8db152592e08..36af14bc13bbbb 100644 --- a/arch/arm/mach-at91/include/mach/system.h +++ b/arch/arm/mach-at91/include/mach/system.h @@ -32,7 +32,11 @@ static inline void arch_idle(void) * Disable the processor clock. The processor will be automatically * re-enabled by an interrupt or by a reset. */ +#ifdef AT91_PS + at91_sys_write(AT91_PS_CR, AT91_PS_CR_CPU); +#else at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK); +#endif #ifndef CONFIG_CPU_ARM920T /* * Set the processor (CP15) into 'Wait for Interrupt' mode. diff --git a/arch/arm/mach-bcmring/arch.c b/arch/arm/mach-bcmring/arch.c index 2f139196d63de6..73eb066d23292e 100644 --- a/arch/arm/mach-bcmring/arch.c +++ b/arch/arm/mach-bcmring/arch.c @@ -167,8 +167,6 @@ static void __init bcmring_fixup(struct machine_desc *desc, MACHINE_START(BCMRING, "BCMRING") /* Maintainer: Broadcom Corporation */ - .phys_io = MM_IO_START, - .io_pg_offst = (MM_IO_BASE >> 18) & 0xfffc, .fixup = bcmring_fixup, .map_io = bcmring_map_io, .init_irq = bcmring_init_irq, diff --git a/arch/arm/mach-bcmring/include/mach/vmalloc.h b/arch/arm/mach-bcmring/include/mach/vmalloc.h index 35e2ead8395c5f..3db3a09fd3986e 100644 --- a/arch/arm/mach-bcmring/include/mach/vmalloc.h +++ b/arch/arm/mach-bcmring/include/mach/vmalloc.h @@ -22,4 +22,4 @@ * 0xe0000000 to 0xefffffff. This gives us 256 MB of vm space and handles * larger physical memory designs better. */ -#define VMALLOC_END (PAGE_OFFSET + 0x30000000) +#define VMALLOC_END 0xf0000000 diff --git a/arch/arm/mach-clps711x/autcpu12.c b/arch/arm/mach-clps711x/autcpu12.c index 5f18eccdc7252a..4a74b2c959bd71 100644 --- a/arch/arm/mach-clps711x/autcpu12.c +++ b/arch/arm/mach-clps711x/autcpu12.c @@ -64,8 +64,6 @@ void __init autcpu12_map_io(void) MACHINE_START(AUTCPU12, "autronix autcpu12") /* Maintainer: Thomas Gleixner */ - .phys_io = 0x80000000, - .io_pg_offst = ((0xff000000) >> 18) & 0xfffc, .boot_params = 0xc0020000, .map_io = autcpu12_map_io, .init_irq = clps711x_init_irq, diff --git a/arch/arm/mach-clps711x/cdb89712.c b/arch/arm/mach-clps711x/cdb89712.c index 71a80b5b8ad613..5a1689d48793c7 100644 --- a/arch/arm/mach-clps711x/cdb89712.c +++ b/arch/arm/mach-clps711x/cdb89712.c @@ -55,8 +55,6 @@ static void __init cdb89712_map_io(void) MACHINE_START(CDB89712, "Cirrus-CDB89712") /* Maintainer: Ray Lehtiniemi */ - .phys_io = 0x80000000, - .io_pg_offst = ((0xff000000) >> 18) & 0xfffc, .boot_params = 0xc0000100, .map_io = cdb89712_map_io, .init_irq = clps711x_init_irq, diff --git a/arch/arm/mach-clps711x/ceiva.c b/arch/arm/mach-clps711x/ceiva.c index 8ada2018497871..16481cf3e931ef 100644 --- a/arch/arm/mach-clps711x/ceiva.c +++ b/arch/arm/mach-clps711x/ceiva.c @@ -56,8 +56,6 @@ static void __init ceiva_map_io(void) MACHINE_START(CEIVA, "CEIVA/Polaroid Photo MAX Digital Picture Frame") /* Maintainer: Rob Scott */ - .phys_io = 0x80000000, - .io_pg_offst = ((0xff000000) >> 18) & 0xfffc, .boot_params = 0xc0000100, .map_io = ceiva_map_io, .init_irq = clps711x_init_irq, diff --git a/arch/arm/mach-clps711x/clep7312.c b/arch/arm/mach-clps711x/clep7312.c index 3c3bf45039ff05..67b5abb4a60a80 100644 --- a/arch/arm/mach-clps711x/clep7312.c +++ b/arch/arm/mach-clps711x/clep7312.c @@ -37,8 +37,6 @@ fixup_clep7312(struct machine_desc *desc, struct tag *tags, MACHINE_START(CLEP7212, "Cirrus Logic 7212/7312") /* Maintainer: Nobody */ - .phys_io = 0x80000000, - .io_pg_offst = ((0xff000000) >> 18) & 0xfffc, .boot_params = 0xc0000100, .fixup = fixup_clep7312, .map_io = clps711x_map_io, diff --git a/arch/arm/mach-clps711x/edb7211-arch.c b/arch/arm/mach-clps711x/edb7211-arch.c index 4a7a2322979a17..98ca5b2e940dd6 100644 --- a/arch/arm/mach-clps711x/edb7211-arch.c +++ b/arch/arm/mach-clps711x/edb7211-arch.c @@ -57,8 +57,6 @@ fixup_edb7211(struct machine_desc *desc, struct tag *tags, MACHINE_START(EDB7211, "CL-EDB7211 (EP7211 eval board)") /* Maintainer: Jon McClintock */ - .phys_io = 0x80000000, - .io_pg_offst = ((0xff000000) >> 18) & 0xfffc, .boot_params = 0xc0020100, /* 0xc0000000 - 0xc001ffff can be video RAM */ .fixup = fixup_edb7211, .map_io = edb7211_map_io, diff --git a/arch/arm/mach-clps711x/fortunet.c b/arch/arm/mach-clps711x/fortunet.c index a696099aa4f8f2..b1cb479e71e909 100644 --- a/arch/arm/mach-clps711x/fortunet.c +++ b/arch/arm/mach-clps711x/fortunet.c @@ -75,8 +75,6 @@ fortunet_fixup(struct machine_desc *desc, struct tag *tags, MACHINE_START(FORTUNET, "ARM-FortuNet") /* Maintainer: FortuNet Inc. */ - .phys_io = 0x80000000, - .io_pg_offst = ((0xf0000000) >> 18) & 0xfffc, .boot_params = 0x00000000, .fixup = fortunet_fixup, .map_io = clps711x_map_io, diff --git a/arch/arm/mach-clps711x/include/mach/debug-macro.S b/arch/arm/mach-clps711x/include/mach/debug-macro.S index 072cc6b61ba30b..507c6873b7ee7e 100644 --- a/arch/arm/mach-clps711x/include/mach/debug-macro.S +++ b/arch/arm/mach-clps711x/include/mach/debug-macro.S @@ -14,16 +14,14 @@ #include #include - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - moveq \rx, #CLPS7111_PHYS_BASE - movne \rx, #CLPS7111_VIRT_BASE + .macro addruart, rp, rv #ifndef CONFIG_DEBUG_CLPS711X_UART2 - add \rx, \rx, #0x0000 @ UART1 + mov \rp, #0x0000 @ UART1 #else - add \rx, \rx, #0x1000 @ UART2 + mov \rp, #0x1000 @ UART2 #endif + orr \rv, \rp, #CLPS7111_VIRT_BASE + orr \rp, \rp, #CLPS7111_PHYS_BASE .endm .macro senduart,rd,rx diff --git a/arch/arm/mach-clps711x/include/mach/vmalloc.h b/arch/arm/mach-clps711x/include/mach/vmalloc.h index ea6cc7beff2879..30b3a287ed8865 100644 --- a/arch/arm/mach-clps711x/include/mach/vmalloc.h +++ b/arch/arm/mach-clps711x/include/mach/vmalloc.h @@ -17,4 +17,4 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ -#define VMALLOC_END (PAGE_OFFSET + 0x10000000) +#define VMALLOC_END 0xd0000000 diff --git a/arch/arm/mach-clps711x/p720t.c b/arch/arm/mach-clps711x/p720t.c index 0d94a30fd6fc84..cefbce0480b95e 100644 --- a/arch/arm/mach-clps711x/p720t.c +++ b/arch/arm/mach-clps711x/p720t.c @@ -89,8 +89,6 @@ static void __init p720t_map_io(void) MACHINE_START(P720T, "ARM-Prospector720T") /* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */ - .phys_io = 0x80000000, - .io_pg_offst = ((0xff000000) >> 18) & 0xfffc, .boot_params = 0xc0000100, .fixup = fixup_p720t, .map_io = p720t_map_io, diff --git a/arch/arm/mach-cns3xxx/cns3420vb.c b/arch/arm/mach-cns3xxx/cns3420vb.c index 9df8391fd78ac9..90fe9ab8591db4 100644 --- a/arch/arm/mach-cns3xxx/cns3420vb.c +++ b/arch/arm/mach-cns3xxx/cns3420vb.c @@ -142,8 +142,6 @@ static void __init cns3420_map_io(void) } MACHINE_START(CNS3420VB, "Cavium Networks CNS3420 Validation Board") - .phys_io = CNS3XXX_UART0_BASE, - .io_pg_offst = (CNS3XXX_UART0_BASE_VIRT >> 18) & 0xfffc, .boot_params = 0x00000100, .map_io = cns3420_map_io, .init_irq = cns3xxx_init_irq, diff --git a/arch/arm/mach-cns3xxx/include/mach/debug-macro.S b/arch/arm/mach-cns3xxx/include/mach/debug-macro.S index d16ce7eb00e909..56d828634db5d8 100644 --- a/arch/arm/mach-cns3xxx/include/mach/debug-macro.S +++ b/arch/arm/mach-cns3xxx/include/mach/debug-macro.S @@ -10,12 +10,10 @@ * published by the Free Software Foundation. */ - .macro addruart,rx - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - moveq \rx, #0x10000000 - movne \rx, #0xf0000000 @ virtual base - orr \rx, \rx, #0x00009000 + .macro addruart,rp,rv + mov \rp, #0x00009000 + orr \rv, \rp, #0xf0000000 @ virtual base + orr \rp, \rp, #0x10000000 .endm #include diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c index c3994f341e4942..7f3cdbfc0fbb52 100644 --- a/arch/arm/mach-davinci/board-da830-evm.c +++ b/arch/arm/mach-davinci/board-da830-evm.c @@ -597,8 +597,6 @@ static void __init da830_evm_map_io(void) } MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137 EVM") - .phys_io = IO_PHYS, - .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, .boot_params = (DA8XX_DDR_BASE + 0x100), .map_io = da830_evm_map_io, .init_irq = cp_intc_init, diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index fdc2cc500fc6ba..b26f5cbfce3e2f 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -817,8 +817,6 @@ static void __init da850_evm_map_io(void) } MACHINE_START(DAVINCI_DA850_EVM, "DaVinci DA850/OMAP-L138 EVM") - .phys_io = IO_PHYS, - .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, .boot_params = (DA8XX_DDR_BASE + 0x100), .map_io = da850_evm_map_io, .init_irq = cp_intc_init, diff --git a/arch/arm/mach-davinci/board-dm355-evm.c b/arch/arm/mach-davinci/board-dm355-evm.c index a3191015efee04..6e7cad13352ce6 100644 --- a/arch/arm/mach-davinci/board-dm355-evm.c +++ b/arch/arm/mach-davinci/board-dm355-evm.c @@ -351,8 +351,6 @@ static __init void dm355_evm_init(void) } MACHINE_START(DAVINCI_DM355_EVM, "DaVinci DM355 EVM") - .phys_io = IO_PHYS, - .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, .boot_params = (0x80000100), .map_io = dm355_evm_map_io, .init_irq = davinci_irq_init, diff --git a/arch/arm/mach-davinci/board-dm355-leopard.c b/arch/arm/mach-davinci/board-dm355-leopard.c index f1d8132cf0c394..543f9911b281e8 100644 --- a/arch/arm/mach-davinci/board-dm355-leopard.c +++ b/arch/arm/mach-davinci/board-dm355-leopard.c @@ -270,8 +270,6 @@ static __init void dm355_leopard_init(void) } MACHINE_START(DM355_LEOPARD, "DaVinci DM355 leopard") - .phys_io = IO_PHYS, - .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, .boot_params = (0x80000100), .map_io = dm355_leopard_map_io, .init_irq = davinci_irq_init, diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c index 84acef1d0b3d98..944a0cbaf5cb7c 100644 --- a/arch/arm/mach-davinci/board-dm365-evm.c +++ b/arch/arm/mach-davinci/board-dm365-evm.c @@ -613,8 +613,6 @@ static __init void dm365_evm_init(void) } MACHINE_START(DAVINCI_DM365_EVM, "DaVinci DM365 EVM") - .phys_io = IO_PHYS, - .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, .boot_params = (0x80000100), .map_io = dm365_evm_map_io, .init_irq = davinci_irq_init, diff --git a/arch/arm/mach-davinci/board-dm644x-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c index 34c8b418cd726f..d59fba15ba8de9 100644 --- a/arch/arm/mach-davinci/board-dm644x-evm.c +++ b/arch/arm/mach-davinci/board-dm644x-evm.c @@ -706,8 +706,6 @@ static __init void davinci_evm_init(void) MACHINE_START(DAVINCI_EVM, "DaVinci DM644x EVM") /* Maintainer: MontaVista Software */ - .phys_io = IO_PHYS, - .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, .boot_params = (DAVINCI_DDR_BASE + 0x100), .map_io = davinci_evm_map_io, .init_irq = davinci_irq_init, diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c index 4502f346b2b04f..6890488fb92b4e 100644 --- a/arch/arm/mach-davinci/board-dm646x-evm.c +++ b/arch/arm/mach-davinci/board-dm646x-evm.c @@ -786,8 +786,6 @@ void __init dm646x_board_setup_refclk(struct clk *clk) } MACHINE_START(DAVINCI_DM6467_EVM, "DaVinci DM646x EVM") - .phys_io = IO_PHYS, - .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, .boot_params = (0x80000100), .map_io = davinci_map_io, .init_irq = davinci_irq_init, @@ -796,8 +794,6 @@ MACHINE_START(DAVINCI_DM6467_EVM, "DaVinci DM646x EVM") MACHINE_END MACHINE_START(DAVINCI_DM6467TEVM, "DaVinci DM6467T EVM") - .phys_io = IO_PHYS, - .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, .boot_params = (0x80000100), .map_io = davinci_map_io, .init_irq = davinci_irq_init, diff --git a/arch/arm/mach-davinci/board-neuros-osd2.c b/arch/arm/mach-davinci/board-neuros-osd2.c index 4c30e929bbf942..a4def889275ccb 100644 --- a/arch/arm/mach-davinci/board-neuros-osd2.c +++ b/arch/arm/mach-davinci/board-neuros-osd2.c @@ -275,8 +275,6 @@ static __init void davinci_ntosd2_init(void) MACHINE_START(NEUROS_OSD2, "Neuros OSD2") /* Maintainer: Neuros Technologies */ - .phys_io = IO_PHYS, - .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, .boot_params = (DAVINCI_DDR_BASE + 0x100), .map_io = davinci_ntosd2_map_io, .init_irq = davinci_irq_init, diff --git a/arch/arm/mach-davinci/board-sffsdr.c b/arch/arm/mach-davinci/board-sffsdr.c index 23e664a1a802a2..9bdf8aafcc840f 100644 --- a/arch/arm/mach-davinci/board-sffsdr.c +++ b/arch/arm/mach-davinci/board-sffsdr.c @@ -154,8 +154,6 @@ static __init void davinci_sffsdr_init(void) MACHINE_START(SFFSDR, "Lyrtech SFFSDR") /* Maintainer: Hugo Villeneuve hugo.villeneuve@lyrtech.com */ - .phys_io = IO_PHYS, - .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, .boot_params = (DAVINCI_DDR_BASE + 0x100), .map_io = davinci_sffsdr_map_io, .init_irq = davinci_irq_init, diff --git a/arch/arm/mach-davinci/board-tnetv107x-evm.c b/arch/arm/mach-davinci/board-tnetv107x-evm.c index fe2a9d9c8bb7bb..b4de35b78904a0 100644 --- a/arch/arm/mach-davinci/board-tnetv107x-evm.c +++ b/arch/arm/mach-davinci/board-tnetv107x-evm.c @@ -164,8 +164,6 @@ console_initcall(tnetv107x_evm_console_init); #endif MACHINE_START(TNETV107X, "TNETV107X EVM") - .phys_io = TNETV107X_IO_BASE, - .io_pg_offst = (TNETV107X_IO_VIRT >> 18) & 0xfffc, .boot_params = (TNETV107X_DDR_BASE + 0x100), .map_io = tnetv107x_init, .init_irq = cp_intc_init, diff --git a/arch/arm/mach-davinci/include/mach/debug-macro.S b/arch/arm/mach-davinci/include/mach/debug-macro.S index f761dfdb8689b3..9f1befc5ac387d 100644 --- a/arch/arm/mach-davinci/include/mach/debug-macro.S +++ b/arch/arm/mach-davinci/include/mach/debug-macro.S @@ -29,35 +29,39 @@ davinci_uart_phys: .word 0 davinci_uart_virt: .word 0 .popsection - .macro addruart, rx, tmp + .macro addruart, rp, rv /* Use davinci_uart_phys/virt if already configured */ -10: mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - ldreq \rx, =__virt_to_phys(davinci_uart_phys) - ldrne \rx, =davinci_uart_virt - ldr \rx, [\rx] - cmp \rx, #0 @ is port configured? +10: mrc p15, 0, \rp, c1, c0 + tst \rp, #1 @ MMU enabled? + ldreq \rp, =__virt_to_phys(davinci_uart_phys) + ldrne \rp, =davinci_uart_phys + add \rv, \rp, #4 @ davinci_uart_virt + ldr \rp, [\rp, #0] + ldr \rv, [\rv, #0] + cmp \rp, #0 @ is port configured? + cmpne \rv, #0 bne 99f @ already configured - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? + /* Check the debug UART address set in uncompress.h */ + mrc p15, 0, \rp, c1, c0 + tst \rp, #1 @ MMU enabled? /* Copy uart phys address from decompressor uart info */ - ldreq \tmp, =__virt_to_phys(davinci_uart_phys) - ldrne \tmp, =davinci_uart_phys - ldreq \rx, =DAVINCI_UART_INFO - ldrne \rx, =__phys_to_virt(DAVINCI_UART_INFO) - ldr \rx, [\rx, #0] - str \rx, [\tmp] + ldreq \rv, =__virt_to_phys(davinci_uart_phys) + ldrne \rv, =davinci_uart_phys + ldreq \rp, =DAVINCI_UART_INFO + ldrne \rp, =__phys_to_virt(DAVINCI_UART_INFO) + ldr \rp, [\rp, #0] + str \rp, [\rv] /* Copy uart virt address from decompressor uart info */ - ldreq \tmp, =__virt_to_phys(davinci_uart_virt) - ldrne \tmp, =davinci_uart_virt - ldreq \rx, =DAVINCI_UART_INFO - ldrne \rx, =__phys_to_virt(DAVINCI_UART_INFO) - ldr \rx, [\rx, #4] - str \rx, [\tmp] + ldreq \rv, =__virt_to_phys(davinci_uart_virt) + ldrne \rv, =davinci_uart_virt + ldreq \rp, =DAVINCI_UART_INFO + ldrne \rp, =__phys_to_virt(DAVINCI_UART_INFO) + ldr \rp, [\rp, #4] + str \rp, [\rv] b 10b 99: diff --git a/arch/arm/mach-dove/dove-db-setup.c b/arch/arm/mach-dove/dove-db-setup.c index bef70460fbc669..95925aa76dd948 100644 --- a/arch/arm/mach-dove/dove-db-setup.c +++ b/arch/arm/mach-dove/dove-db-setup.c @@ -94,8 +94,6 @@ static void __init dove_db_init(void) } MACHINE_START(DOVE_DB, "Marvell DB-MV88AP510-BP Development Board") - .phys_io = DOVE_SB_REGS_PHYS_BASE, - .io_pg_offst = ((DOVE_SB_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = dove_db_init, .map_io = dove_map_io, diff --git a/arch/arm/mach-dove/include/mach/debug-macro.S b/arch/arm/mach-dove/include/mach/debug-macro.S index 1521d13f1d1492..da8bf2bad3b1df 100644 --- a/arch/arm/mach-dove/include/mach/debug-macro.S +++ b/arch/arm/mach-dove/include/mach/debug-macro.S @@ -8,12 +8,11 @@ #include - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - ldreq \rx, =DOVE_SB_REGS_PHYS_BASE - ldrne \rx, =DOVE_SB_REGS_VIRT_BASE - orr \rx, \rx, #0x00012000 + .macro addruart, rp, rv + ldr \rp, =DOVE_SB_REGS_PHYS_BASE + ldr \rv, =DOVE_SB_REGS_VIRT_BASE + orr \rp, \rp, #0x00012000 + orr \rv, \rv, #0x00012000 .endm #define UART_SHIFT 2 diff --git a/arch/arm/mach-ebsa110/core.c b/arch/arm/mach-ebsa110/core.c index c7bc7fbb11a647..5df4099fc14fbd 100644 --- a/arch/arm/mach-ebsa110/core.c +++ b/arch/arm/mach-ebsa110/core.c @@ -280,8 +280,6 @@ arch_initcall(ebsa110_init); MACHINE_START(EBSA110, "EBSA110") /* Maintainer: Russell King */ - .phys_io = 0xe0000000, - .io_pg_offst = ((0xe0000000) >> 18) & 0xfffc, .boot_params = 0x00000400, .reserve_lp0 = 1, .reserve_lp2 = 1, diff --git a/arch/arm/mach-ebsa110/include/mach/debug-macro.S b/arch/arm/mach-ebsa110/include/mach/debug-macro.S index ebbd89f0e6c0e8..7ef5690fd08c87 100644 --- a/arch/arm/mach-ebsa110/include/mach/debug-macro.S +++ b/arch/arm/mach-ebsa110/include/mach/debug-macro.S @@ -11,9 +11,10 @@ * **/ - .macro addruart, rx, tmp - mov \rx, #0xf0000000 - orr \rx, \rx, #0x00000be0 + .macro addruart, rp, rv + mov \rp, #0xf0000000 + orr \rp, \rp, #0x00000be0 + mov \rp, \rv .endm #define UART_SHIFT 2 diff --git a/arch/arm/mach-ebsa110/include/mach/vmalloc.h b/arch/arm/mach-ebsa110/include/mach/vmalloc.h index 9b44c19e95ec51..60bde56fba4cf3 100644 --- a/arch/arm/mach-ebsa110/include/mach/vmalloc.h +++ b/arch/arm/mach-ebsa110/include/mach/vmalloc.h @@ -7,4 +7,4 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ -#define VMALLOC_END (PAGE_OFFSET + 0x1f000000) +#define VMALLOC_END 0xdf000000 diff --git a/arch/arm/mach-ep93xx/adssphere.c b/arch/arm/mach-ep93xx/adssphere.c index f744f676783f30..61b98ce4b67354 100644 --- a/arch/arm/mach-ep93xx/adssphere.c +++ b/arch/arm/mach-ep93xx/adssphere.c @@ -33,8 +33,6 @@ static void __init adssphere_init_machine(void) MACHINE_START(ADSSPHERE, "ADS Sphere board") /* Maintainer: Lennert Buytenhek */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, diff --git a/arch/arm/mach-ep93xx/edb93xx.c b/arch/arm/mach-ep93xx/edb93xx.c index c2ce9034ba87f5..4b04316521318f 100644 --- a/arch/arm/mach-ep93xx/edb93xx.c +++ b/arch/arm/mach-ep93xx/edb93xx.c @@ -124,8 +124,6 @@ static void __init edb93xx_init_machine(void) #ifdef CONFIG_MACH_EDB9301 MACHINE_START(EDB9301, "Cirrus Logic EDB9301 Evaluation Board") /* Maintainer: H Hartley Sweeten */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, @@ -137,8 +135,6 @@ MACHINE_END #ifdef CONFIG_MACH_EDB9302 MACHINE_START(EDB9302, "Cirrus Logic EDB9302 Evaluation Board") /* Maintainer: George Kashperko */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, @@ -150,8 +146,6 @@ MACHINE_END #ifdef CONFIG_MACH_EDB9302A MACHINE_START(EDB9302A, "Cirrus Logic EDB9302A Evaluation Board") /* Maintainer: Lennert Buytenhek */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE0_PHYS_BASE + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, @@ -163,8 +157,6 @@ MACHINE_END #ifdef CONFIG_MACH_EDB9307 MACHINE_START(EDB9307, "Cirrus Logic EDB9307 Evaluation Board") /* Maintainer: Herbert Valerio Riedel */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, @@ -176,8 +168,6 @@ MACHINE_END #ifdef CONFIG_MACH_EDB9307A MACHINE_START(EDB9307A, "Cirrus Logic EDB9307A Evaluation Board") /* Maintainer: H Hartley Sweeten */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE0_PHYS_BASE + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, @@ -189,8 +179,6 @@ MACHINE_END #ifdef CONFIG_MACH_EDB9312 MACHINE_START(EDB9312, "Cirrus Logic EDB9312 Evaluation Board") /* Maintainer: Toufeeq Hussain */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, @@ -202,8 +190,6 @@ MACHINE_END #ifdef CONFIG_MACH_EDB9315 MACHINE_START(EDB9315, "Cirrus Logic EDB9315 Evaluation Board") /* Maintainer: Lennert Buytenhek */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, @@ -215,8 +201,6 @@ MACHINE_END #ifdef CONFIG_MACH_EDB9315A MACHINE_START(EDB9315A, "Cirrus Logic EDB9315A Evaluation Board") /* Maintainer: Lennert Buytenhek */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE0_PHYS_BASE + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, diff --git a/arch/arm/mach-ep93xx/gesbc9312.c b/arch/arm/mach-ep93xx/gesbc9312.c index d97168c0ba336f..9bd3152bff9a12 100644 --- a/arch/arm/mach-ep93xx/gesbc9312.c +++ b/arch/arm/mach-ep93xx/gesbc9312.c @@ -33,8 +33,6 @@ static void __init gesbc9312_init_machine(void) MACHINE_START(GESBC9312, "Glomation GESBC-9312-sx") /* Maintainer: Lennert Buytenhek */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, diff --git a/arch/arm/mach-ep93xx/include/mach/debug-macro.S b/arch/arm/mach-ep93xx/include/mach/debug-macro.S index 5cd22444e2236a..b25bc90763673d 100644 --- a/arch/arm/mach-ep93xx/include/mach/debug-macro.S +++ b/arch/arm/mach-ep93xx/include/mach/debug-macro.S @@ -11,12 +11,11 @@ */ #include - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - ldreq \rx, =EP93XX_APB_PHYS_BASE @ Physical base - ldrne \rx, =EP93XX_APB_VIRT_BASE @ virtual base - orr \rx, \rx, #0x000c0000 + .macro addruart, rp, rv + ldr \rp, =EP93XX_APB_PHYS_BASE @ Physical base + ldr \rv, =EP93XX_APB_VIRT_BASE @ virtual base + orr \rp, \rp, #0x000c0000 + orr \rv, \rv, #0x000c0000 .endm #include diff --git a/arch/arm/mach-ep93xx/micro9.c b/arch/arm/mach-ep93xx/micro9.c index 2ba776320a8282..7adea6258efeb0 100644 --- a/arch/arm/mach-ep93xx/micro9.c +++ b/arch/arm/mach-ep93xx/micro9.c @@ -77,8 +77,6 @@ static void __init micro9_init_machine(void) #ifdef CONFIG_MACH_MICRO9H MACHINE_START(MICRO9, "Contec Micro9-High") /* Maintainer: Hubert Feurstein */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, @@ -90,8 +88,6 @@ MACHINE_END #ifdef CONFIG_MACH_MICRO9M MACHINE_START(MICRO9M, "Contec Micro9-Mid") /* Maintainer: Hubert Feurstein */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE3_PHYS_BASE_ASYNC + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, @@ -103,8 +99,6 @@ MACHINE_END #ifdef CONFIG_MACH_MICRO9L MACHINE_START(MICRO9L, "Contec Micro9-Lite") /* Maintainer: Hubert Feurstein */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, @@ -116,8 +110,6 @@ MACHINE_END #ifdef CONFIG_MACH_MICRO9S MACHINE_START(MICRO9S, "Contec Micro9-Slim") /* Maintainer: Hubert Feurstein */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE3_PHYS_BASE_ASYNC + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, diff --git a/arch/arm/mach-ep93xx/simone.c b/arch/arm/mach-ep93xx/simone.c index 5dded5884133f8..f22ce8db7947b6 100644 --- a/arch/arm/mach-ep93xx/simone.c +++ b/arch/arm/mach-ep93xx/simone.c @@ -65,8 +65,6 @@ static void __init simone_init_machine(void) MACHINE_START(SIM_ONE, "Simplemachines Sim.One Board") /* Maintainer: Ryan Mallon */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE0_PHYS_BASE + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, diff --git a/arch/arm/mach-ep93xx/snappercl15.c b/arch/arm/mach-ep93xx/snappercl15.c index a12c89301297f6..ac601fe2b448b4 100644 --- a/arch/arm/mach-ep93xx/snappercl15.c +++ b/arch/arm/mach-ep93xx/snappercl15.c @@ -163,8 +163,6 @@ static void __init snappercl15_init_machine(void) MACHINE_START(SNAPPER_CL15, "Bluewater Systems Snapper CL15") /* Maintainer: Ryan Mallon */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE0_PHYS_BASE + 0x100, .map_io = ep93xx_map_io, .init_irq = ep93xx_init_irq, diff --git a/arch/arm/mach-ep93xx/ts72xx.c b/arch/arm/mach-ep93xx/ts72xx.c index 93aeab8af705e8..c2d2cf40ead920 100644 --- a/arch/arm/mach-ep93xx/ts72xx.c +++ b/arch/arm/mach-ep93xx/ts72xx.c @@ -257,8 +257,6 @@ static void __init ts72xx_init_machine(void) MACHINE_START(TS72XX, "Technologic Systems TS-72xx SBC") /* Maintainer: Lennert Buytenhek */ - .phys_io = EP93XX_APB_PHYS_BASE, - .io_pg_offst = ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc, .boot_params = EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100, .map_io = ts72xx_map_io, .init_irq = ep93xx_init_irq, diff --git a/arch/arm/mach-footbridge/cats-hw.c b/arch/arm/mach-footbridge/cats-hw.c index 1b996b26d2e0d0..5b1a8db779be1d 100644 --- a/arch/arm/mach-footbridge/cats-hw.c +++ b/arch/arm/mach-footbridge/cats-hw.c @@ -86,8 +86,6 @@ fixup_cats(struct machine_desc *desc, struct tag *tags, MACHINE_START(CATS, "Chalice-CATS") /* Maintainer: Philip Blundell */ - .phys_io = DC21285_ARMCSR_BASE, - .io_pg_offst = ((0xfe000000) >> 18) & 0xfffc, .boot_params = 0x00000100, .soft_reboot = 1, .fixup = fixup_cats, diff --git a/arch/arm/mach-footbridge/ebsa285.c b/arch/arm/mach-footbridge/ebsa285.c index 30040fd588cc01..2ef69ff44ba807 100644 --- a/arch/arm/mach-footbridge/ebsa285.c +++ b/arch/arm/mach-footbridge/ebsa285.c @@ -15,8 +15,6 @@ MACHINE_START(EBSA285, "EBSA285") /* Maintainer: Russell King */ - .phys_io = DC21285_ARMCSR_BASE, - .io_pg_offst = ((0xfe000000) >> 18) & 0xfffc, .boot_params = 0x00000100, .video_start = 0x000a0000, .video_end = 0x000bffff, diff --git a/arch/arm/mach-footbridge/include/mach/debug-macro.S b/arch/arm/mach-footbridge/include/mach/debug-macro.S index 60dda1318f2285..3c9e0c40c67919 100644 --- a/arch/arm/mach-footbridge/include/mach/debug-macro.S +++ b/arch/arm/mach-footbridge/include/mach/debug-macro.S @@ -15,12 +15,10 @@ #ifndef CONFIG_DEBUG_DC21285_PORT /* For NetWinder debugging */ - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - moveq \rx, #0x7c000000 @ physical - movne \rx, #0xff000000 @ virtual - orr \rx, \rx, #0x000003f8 + .macro addruart, rp, rv + mov \rp, #0x000003f8 + orr \rv, \rp, #0x7c000000 @ physical + orr \rp, \rp, #0xff000000 @ virtual .endm #define UART_SHIFT 0 @@ -32,14 +30,14 @@ .equ dc21285_high, ARMCSR_BASE & 0xff000000 .equ dc21285_low, ARMCSR_BASE & 0x00ffffff - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - moveq \rx, #0x42000000 - movne \rx, #dc21285_high + .macro addruart, rp, rv .if dc21285_low - orrne \rx, \rx, #dc21285_low + mov \rp, #dc21285_low + .else + mov \rp, #0 .endif + orr \rv, \rp, #0x42000000 + orr \rp, \rp, #dc21285_high .endm .macro senduart,rd,rx diff --git a/arch/arm/mach-footbridge/include/mach/vmalloc.h b/arch/arm/mach-footbridge/include/mach/vmalloc.h index d0958d860a3cb5..0ffbb7c85e59e7 100644 --- a/arch/arm/mach-footbridge/include/mach/vmalloc.h +++ b/arch/arm/mach-footbridge/include/mach/vmalloc.h @@ -7,4 +7,4 @@ */ -#define VMALLOC_END (PAGE_OFFSET + 0x30000000) +#define VMALLOC_END 0xf0000000 diff --git a/arch/arm/mach-footbridge/netwinder-hw.c b/arch/arm/mach-footbridge/netwinder-hw.c index ac7ffa6fc413e7..06e514f372d0f2 100644 --- a/arch/arm/mach-footbridge/netwinder-hw.c +++ b/arch/arm/mach-footbridge/netwinder-hw.c @@ -648,8 +648,6 @@ fixup_netwinder(struct machine_desc *desc, struct tag *tags, MACHINE_START(NETWINDER, "Rebel-NetWinder") /* Maintainer: Russell King/Rebel.com */ - .phys_io = DC21285_ARMCSR_BASE, - .io_pg_offst = ((0xfe000000) >> 18) & 0xfffc, .boot_params = 0x00000100, .video_start = 0x000a0000, .video_end = 0x000bffff, diff --git a/arch/arm/mach-footbridge/personal.c b/arch/arm/mach-footbridge/personal.c index e2c9f0690b1622..3285e91ca8c1dc 100644 --- a/arch/arm/mach-footbridge/personal.c +++ b/arch/arm/mach-footbridge/personal.c @@ -15,8 +15,6 @@ MACHINE_START(PERSONAL_SERVER, "Compaq-PersonalServer") /* Maintainer: Jamey Hicks / George France */ - .phys_io = DC21285_ARMCSR_BASE, - .io_pg_offst = ((0xfe000000) >> 18) & 0xfffc, .boot_params = 0x00000100, .map_io = footbridge_map_io, .init_irq = footbridge_init_irq, diff --git a/arch/arm/mach-gemini/board-nas4220b.c b/arch/arm/mach-gemini/board-nas4220b.c index 01f1d6daab448c..2ba096de00348e 100644 --- a/arch/arm/mach-gemini/board-nas4220b.c +++ b/arch/arm/mach-gemini/board-nas4220b.c @@ -101,8 +101,6 @@ static void __init ib4220b_init(void) } MACHINE_START(NAS4220B, "Raidsonic NAS IB-4220-B") - .phys_io = 0x7fffc000, - .io_pg_offst = ((0xffffc000) >> 18) & 0xfffc, .boot_params = 0x100, .map_io = gemini_map_io, .init_irq = gemini_init_irq, diff --git a/arch/arm/mach-gemini/board-rut1xx.c b/arch/arm/mach-gemini/board-rut1xx.c index e0de968e32a6e0..a9a0d8b0194296 100644 --- a/arch/arm/mach-gemini/board-rut1xx.c +++ b/arch/arm/mach-gemini/board-rut1xx.c @@ -85,8 +85,6 @@ static void __init rut1xx_init(void) } MACHINE_START(RUT100, "Teltonika RUT100") - .phys_io = 0x7fffc000, - .io_pg_offst = ((0xffffc000) >> 18) & 0xfffc, .boot_params = 0x100, .map_io = gemini_map_io, .init_irq = gemini_init_irq, diff --git a/arch/arm/mach-gemini/board-wbd111.c b/arch/arm/mach-gemini/board-wbd111.c index 36538c15b3c434..8b88d50d4337db 100644 --- a/arch/arm/mach-gemini/board-wbd111.c +++ b/arch/arm/mach-gemini/board-wbd111.c @@ -133,8 +133,6 @@ static void __init wbd111_init(void) } MACHINE_START(WBD111, "Wiliboard WBD-111") - .phys_io = 0x7fffc000, - .io_pg_offst = ((0xffffc000) >> 18) & 0xfffc, .boot_params = 0x100, .map_io = gemini_map_io, .init_irq = gemini_init_irq, diff --git a/arch/arm/mach-gemini/board-wbd222.c b/arch/arm/mach-gemini/board-wbd222.c index ece8b4c6511030..1eebcecd1c3312 100644 --- a/arch/arm/mach-gemini/board-wbd222.c +++ b/arch/arm/mach-gemini/board-wbd222.c @@ -133,8 +133,6 @@ static void __init wbd222_init(void) } MACHINE_START(WBD222, "Wiliboard WBD-222") - .phys_io = 0x7fffc000, - .io_pg_offst = ((0xffffc000) >> 18) & 0xfffc, .boot_params = 0x100, .map_io = gemini_map_io, .init_irq = gemini_init_irq, diff --git a/arch/arm/mach-gemini/include/mach/debug-macro.S b/arch/arm/mach-gemini/include/mach/debug-macro.S index ad477047069ddc..f40e006d296e66 100644 --- a/arch/arm/mach-gemini/include/mach/debug-macro.S +++ b/arch/arm/mach-gemini/include/mach/debug-macro.S @@ -11,11 +11,9 @@ */ #include - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - ldreq \rx, =GEMINI_UART_BASE @ physical - ldrne \rx, =IO_ADDRESS(GEMINI_UART_BASE) @ virtual + .macro addruart, rp, rv + ldr \rp, =GEMINI_UART_BASE @ physical + ldr \rv, =IO_ADDRESS(GEMINI_UART_BASE) @ virtual .endm #define UART_SHIFT 2 diff --git a/arch/arm/mach-h720x/h7201-eval.c b/arch/arm/mach-h720x/h7201-eval.c index 78be457dc32431..79f0b896e446c6 100644 --- a/arch/arm/mach-h720x/h7201-eval.c +++ b/arch/arm/mach-h720x/h7201-eval.c @@ -30,8 +30,6 @@ MACHINE_START(H7201, "Hynix GMS30C7201") /* Maintainer: Robert Schwebel, Pengutronix */ - .phys_io = 0x80000000, - .io_pg_offst = ((0xf0000000) >> 18) & 0xfffc, .boot_params = 0xc0001000, .map_io = h720x_map_io, .init_irq = h720x_init_irq, diff --git a/arch/arm/mach-h720x/h7202-eval.c b/arch/arm/mach-h720x/h7202-eval.c index 8c0ba99d683fea..cc28b1efe0472e 100644 --- a/arch/arm/mach-h720x/h7202-eval.c +++ b/arch/arm/mach-h720x/h7202-eval.c @@ -72,8 +72,6 @@ static void __init init_eval_h7202(void) MACHINE_START(H7202, "Hynix HMS30C7202") /* Maintainer: Robert Schwebel, Pengutronix */ - .phys_io = 0x80000000, - .io_pg_offst = ((0xf0000000) >> 18) & 0xfffc, .boot_params = 0x40000100, .map_io = h720x_map_io, .init_irq = h7202_init_irq, diff --git a/arch/arm/mach-h720x/include/mach/debug-macro.S b/arch/arm/mach-h720x/include/mach/debug-macro.S index 27cafd12f033cb..c2093e835720f5 100644 --- a/arch/arm/mach-h720x/include/mach/debug-macro.S +++ b/arch/arm/mach-h720x/include/mach/debug-macro.S @@ -16,12 +16,10 @@ .equ io_virt, IO_VIRT .equ io_phys, IO_PHYS - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - moveq \rx, #io_phys @ physical base address - movne \rx, #io_virt @ virtual address - add \rx, \rx, #0x00020000 @ UART1 + .macro addruart, rp, rv + mov \rp, #0x00020000 @ UART1 + add \rv, \rp, #io_virt @ virtual address + add \rp, \rp, #io_phys @ physical base address .endm .macro senduart,rd,rx diff --git a/arch/arm/mach-h720x/include/mach/vmalloc.h b/arch/arm/mach-h720x/include/mach/vmalloc.h index ff1460d6841ba9..a45915b88756d4 100644 --- a/arch/arm/mach-h720x/include/mach/vmalloc.h +++ b/arch/arm/mach-h720x/include/mach/vmalloc.h @@ -5,6 +5,6 @@ #ifndef __ARCH_ARM_VMALLOC_H #define __ARCH_ARM_VMALLOC_H -#define VMALLOC_END (PAGE_OFFSET + 0x10000000) +#define VMALLOC_END 0xd0000000 #endif diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index 2f7e2728970d66..197f9e241cffc3 100644 --- a/arch/arm/mach-imx/Kconfig +++ b/arch/arm/mach-imx/Kconfig @@ -147,8 +147,8 @@ choice default MACH_EUKREA_MBIMX27_BASEBOARD config MACH_EUKREA_MBIMX27_BASEBOARD - prompt "Eukrea MBIMX27 development board" - bool + bool "Eukrea MBIMX27 development board" + select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_SPI_IMX help @@ -164,6 +164,15 @@ config MACH_MX27_3DS Include support for MX27PDK platform. This includes specific configurations for the board and its peripherals. +config MACH_IMX27_VISSTRIM_M10 + bool "Vista Silicon i.MX27 Visstrim_m10" + select IMX_HAVE_PLATFORM_IMX_I2C + select IMX_HAVE_PLATFORM_IMX_UART + help + Include support for Visstrim_m10 platform and its different variants. + This includes specific configurations for the board and its + peripherals. + config MACH_IMX27LITE bool "LogicPD MX27 LITEKIT platform" select IMX_HAVE_PLATFORM_IMX_UART @@ -174,6 +183,7 @@ config MACH_IMX27LITE config MACH_PCA100 bool "Phytec phyCARD-s (pca100)" select IMX_HAVE_PLATFORM_IMX_I2C + select IMX_HAVE_PLATFORM_IMX_SSI select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_MXC_NAND select IMX_HAVE_PLATFORM_SPI_IMX diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile index 46a9fdfbbd1571..5582692bb17695 100644 --- a/arch/arm/mach-imx/Makefile +++ b/arch/arm/mach-imx/Makefile @@ -27,6 +27,7 @@ obj-$(CONFIG_MACH_PCM038) += mach-pcm038.o obj-$(CONFIG_MACH_PCM970_BASEBOARD) += pcm970-baseboard.o obj-$(CONFIG_MACH_MX27_3DS) += mach-mx27_3ds.o obj-$(CONFIG_MACH_IMX27LITE) += mach-imx27lite.o +obj-$(CONFIG_MACH_IMX27_VISSTRIM_M10) += mach-imx27_visstrim_m10.o obj-$(CONFIG_MACH_CPUIMX27) += mach-cpuimx27.o obj-$(CONFIG_MACH_EUKREA_MBIMX27_BASEBOARD) += eukrea_mbimx27-baseboard.o obj-$(CONFIG_MACH_PCA100) += mach-pca100.o diff --git a/arch/arm/mach-imx/clock-imx1.c b/arch/arm/mach-imx/clock-imx1.c index c05096c3830103..daca30b2d5b1ad 100644 --- a/arch/arm/mach-imx/clock-imx1.c +++ b/arch/arm/mach-imx/clock-imx1.c @@ -592,7 +592,7 @@ static struct clk_lookup lookups[] __initdata = { _REGISTER_CLOCK("imx-uart.1", NULL, uart_clk) _REGISTER_CLOCK("imx-uart.2", NULL, uart_clk) _REGISTER_CLOCK("imx-i2c.0", NULL, i2c_clk) - _REGISTER_CLOCK("spi_imx.0", NULL, spi_clk) + _REGISTER_CLOCK("imx1-cspi.0", NULL, spi_clk) _REGISTER_CLOCK("imx-mmc.0", NULL, sdhc_clk) _REGISTER_CLOCK("imx-fb.0", NULL, lcdc_clk) _REGISTER_CLOCK(NULL, "mshc", mshc_clk) diff --git a/arch/arm/mach-imx/clock-imx21.c b/arch/arm/mach-imx/clock-imx21.c index bb419ef4d133bb..cf15ea516a72c4 100644 --- a/arch/arm/mach-imx/clock-imx21.c +++ b/arch/arm/mach-imx/clock-imx21.c @@ -1172,9 +1172,9 @@ static struct clk_lookup lookups[] = { _REGISTER_CLOCK(NULL, "pwm", pwm_clk[0]) _REGISTER_CLOCK(NULL, "sdhc1", sdhc_clk[0]) _REGISTER_CLOCK(NULL, "sdhc2", sdhc_clk[1]) - _REGISTER_CLOCK(NULL, "cspi1", cspi_clk[0]) - _REGISTER_CLOCK(NULL, "cspi2", cspi_clk[1]) - _REGISTER_CLOCK(NULL, "cspi3", cspi_clk[2]) + _REGISTER_CLOCK("imx21-cspi.0", NULL, cspi_clk[0]) + _REGISTER_CLOCK("imx21-cspi.1", NULL, cspi_clk[1]) + _REGISTER_CLOCK("imx21-cspi.2", NULL, cspi_clk[2]) _REGISTER_CLOCK("imx-fb.0", NULL, lcdc_clk[0]) _REGISTER_CLOCK(NULL, "csi", csi_clk[0]) _REGISTER_CLOCK("imx21-hcd.0", NULL, usb_clk[0]) diff --git a/arch/arm/mach-imx/clock-imx27.c b/arch/arm/mach-imx/clock-imx27.c index 5a1aa15c8a1614..98a25bada783fe 100644 --- a/arch/arm/mach-imx/clock-imx27.c +++ b/arch/arm/mach-imx/clock-imx27.c @@ -594,27 +594,27 @@ DEFINE_CLOCK(uart2_clk1, 0, PCCR1, 30, NULL, NULL, &ipg_clk); DEFINE_CLOCK(uart1_clk1, 0, PCCR1, 31, NULL, NULL, &ipg_clk); /* Clocks we cannot directly gate, but drivers need their rates */ -DEFINE_CLOCK(cspi1_clk, 0, 0, 0, NULL, &cspi1_clk1, &per2_clk); -DEFINE_CLOCK(cspi2_clk, 1, 0, 0, NULL, &cspi2_clk1, &per2_clk); -DEFINE_CLOCK(cspi3_clk, 2, 0, 0, NULL, &cspi13_clk1, &per2_clk); -DEFINE_CLOCK(sdhc1_clk, 0, 0, 0, NULL, &sdhc1_clk1, &per2_clk); -DEFINE_CLOCK(sdhc2_clk, 1, 0, 0, NULL, &sdhc2_clk1, &per2_clk); -DEFINE_CLOCK(sdhc3_clk, 2, 0, 0, NULL, &sdhc3_clk1, &per2_clk); -DEFINE_CLOCK(pwm_clk, 0, 0, 0, NULL, &pwm_clk1, &per1_clk); -DEFINE_CLOCK(gpt1_clk, 0, 0, 0, NULL, &gpt1_clk1, &per1_clk); -DEFINE_CLOCK(gpt2_clk, 1, 0, 0, NULL, &gpt2_clk1, &per1_clk); -DEFINE_CLOCK(gpt3_clk, 2, 0, 0, NULL, &gpt3_clk1, &per1_clk); -DEFINE_CLOCK(gpt4_clk, 3, 0, 0, NULL, &gpt4_clk1, &per1_clk); -DEFINE_CLOCK(gpt5_clk, 4, 0, 0, NULL, &gpt5_clk1, &per1_clk); -DEFINE_CLOCK(gpt6_clk, 5, 0, 0, NULL, &gpt6_clk1, &per1_clk); -DEFINE_CLOCK(uart1_clk, 0, 0, 0, NULL, &uart1_clk1, &per1_clk); -DEFINE_CLOCK(uart2_clk, 1, 0, 0, NULL, &uart2_clk1, &per1_clk); -DEFINE_CLOCK(uart3_clk, 2, 0, 0, NULL, &uart3_clk1, &per1_clk); -DEFINE_CLOCK(uart4_clk, 3, 0, 0, NULL, &uart4_clk1, &per1_clk); -DEFINE_CLOCK(uart5_clk, 4, 0, 0, NULL, &uart5_clk1, &per1_clk); -DEFINE_CLOCK(uart6_clk, 5, 0, 0, NULL, &uart6_clk1, &per1_clk); -DEFINE_CLOCK1(lcdc_clk, 0, 0, 0, parent, &lcdc_clk1, &per3_clk); -DEFINE_CLOCK1(csi_clk, 0, 0, 0, parent, &csi_clk1, &per4_clk); +DEFINE_CLOCK(cspi1_clk, 0, NULL, 0, NULL, &cspi1_clk1, &per2_clk); +DEFINE_CLOCK(cspi2_clk, 1, NULL, 0, NULL, &cspi2_clk1, &per2_clk); +DEFINE_CLOCK(cspi3_clk, 2, NULL, 0, NULL, &cspi13_clk1, &per2_clk); +DEFINE_CLOCK(sdhc1_clk, 0, NULL, 0, NULL, &sdhc1_clk1, &per2_clk); +DEFINE_CLOCK(sdhc2_clk, 1, NULL, 0, NULL, &sdhc2_clk1, &per2_clk); +DEFINE_CLOCK(sdhc3_clk, 2, NULL, 0, NULL, &sdhc3_clk1, &per2_clk); +DEFINE_CLOCK(pwm_clk, 0, NULL, 0, NULL, &pwm_clk1, &per1_clk); +DEFINE_CLOCK(gpt1_clk, 0, NULL, 0, NULL, &gpt1_clk1, &per1_clk); +DEFINE_CLOCK(gpt2_clk, 1, NULL, 0, NULL, &gpt2_clk1, &per1_clk); +DEFINE_CLOCK(gpt3_clk, 2, NULL, 0, NULL, &gpt3_clk1, &per1_clk); +DEFINE_CLOCK(gpt4_clk, 3, NULL, 0, NULL, &gpt4_clk1, &per1_clk); +DEFINE_CLOCK(gpt5_clk, 4, NULL, 0, NULL, &gpt5_clk1, &per1_clk); +DEFINE_CLOCK(gpt6_clk, 5, NULL, 0, NULL, &gpt6_clk1, &per1_clk); +DEFINE_CLOCK(uart1_clk, 0, NULL, 0, NULL, &uart1_clk1, &per1_clk); +DEFINE_CLOCK(uart2_clk, 1, NULL, 0, NULL, &uart2_clk1, &per1_clk); +DEFINE_CLOCK(uart3_clk, 2, NULL, 0, NULL, &uart3_clk1, &per1_clk); +DEFINE_CLOCK(uart4_clk, 3, NULL, 0, NULL, &uart4_clk1, &per1_clk); +DEFINE_CLOCK(uart5_clk, 4, NULL, 0, NULL, &uart5_clk1, &per1_clk); +DEFINE_CLOCK(uart6_clk, 5, NULL, 0, NULL, &uart6_clk1, &per1_clk); +DEFINE_CLOCK1(lcdc_clk, 0, NULL, 0, parent, &lcdc_clk1, &per3_clk); +DEFINE_CLOCK1(csi_clk, 0, NULL, 0, parent, &csi_clk1, &per4_clk); #define _REGISTER_CLOCK(d, n, c) \ { \ @@ -640,9 +640,9 @@ static struct clk_lookup lookups[] = { _REGISTER_CLOCK("mxc-mmc.0", NULL, sdhc1_clk) _REGISTER_CLOCK("mxc-mmc.1", NULL, sdhc2_clk) _REGISTER_CLOCK("mxc-mmc.2", NULL, sdhc3_clk) - _REGISTER_CLOCK("spi_imx.0", NULL, cspi1_clk) - _REGISTER_CLOCK("spi_imx.1", NULL, cspi2_clk) - _REGISTER_CLOCK("spi_imx.2", NULL, cspi3_clk) + _REGISTER_CLOCK("imx27-cspi.0", NULL, cspi1_clk) + _REGISTER_CLOCK("imx27-cspi.1", NULL, cspi2_clk) + _REGISTER_CLOCK("imx27-cspi.2", NULL, cspi3_clk) _REGISTER_CLOCK("imx-fb.0", NULL, lcdc_clk) _REGISTER_CLOCK("mx2-camera.0", NULL, csi_clk) _REGISTER_CLOCK("fsl-usb2-udc", "usb", usb_clk) diff --git a/arch/arm/mach-imx/devices-imx1.h b/arch/arm/mach-imx/devices-imx1.h index a8d94f078196cb..81979486218ed0 100644 --- a/arch/arm/mach-imx/devices-imx1.h +++ b/arch/arm/mach-imx/devices-imx1.h @@ -9,10 +9,12 @@ #include #include -#define imx1_add_i2c_imx(pdata) \ - imx_add_imx_i2c(0, MX1_I2C_BASE_ADDR, SZ_4K, MX1_INT_I2C, pdata) +extern const struct imx_imx_i2c_data imx1_imx_i2c_data __initconst; +#define imx1_add_imx_i2c(pdata) \ + imx_add_imx_i2c(&imx1_imx_i2c_data, pdata) -#define imx1_add_imx_uart0(pdata) \ - imx_add_imx_uart_3irq(0, MX1_UART1_BASE_ADDR, 0xd0, MX1_INT_UART1RX, MX1_INT_UART1TX, MX1_INT_UART1RTS, pdata) -#define imx1_add_imx_uart1(pdata) \ - imx_add_imx_uart_3irq(0, MX1_UART2_BASE_ADDR, 0xd0, MX1_INT_UART2RX, MX1_INT_UART2TX, MX1_INT_UART2RTS, pdata) +extern const struct imx_imx_uart_3irq_data imx1_imx_uart_data[] __initconst; +#define imx1_add_imx_uart(id, pdata) \ + imx_add_imx_uart_3irq(&imx1_imx_uart_data[id], pdata) +#define imx1_add_imx_uart0(pdata) imx1_add_imx_uart(0, pdata) +#define imx1_add_imx_uart1(pdata) imx1_add_imx_uart(1, pdata) diff --git a/arch/arm/mach-imx/devices-imx21.h b/arch/arm/mach-imx/devices-imx21.h index 42788e99d12729..d189039749b090 100644 --- a/arch/arm/mach-imx/devices-imx21.h +++ b/arch/arm/mach-imx/devices-imx21.h @@ -9,22 +9,28 @@ #include #include -#define imx21_add_i2c_imx(pdata) \ - imx_add_imx_i2c(0, MX2x_I2C_BASE_ADDR, SZ_4K, MX2x_INT_I2C, pdata) +extern const struct imx_imx_i2c_data imx21_imx_i2c_data __initconst; +#define imx21_add_imx_i2c(pdata) \ + imx_add_imx_i2c(&imx21_imx_i2c_data, pdata) -#define imx21_add_imx_uart0(pdata) \ - imx_add_imx_uart_1irq(0, MX21_UART1_BASE_ADDR, SZ_4K, MX21_INT_UART1, pdata) -#define imx21_add_imx_uart1(pdata) \ - imx_add_imx_uart_1irq(1, MX21_UART2_BASE_ADDR, SZ_4K, MX21_INT_UART2, pdata) -#define imx21_add_imx_uart2(pdata) \ - imx_add_imx_uart_1irq(2, MX21_UART3_BASE_ADDR, SZ_4K, MX21_INT_UART3, pdata) -#define imx21_add_imx_uart3(pdata) \ - imx_add_imx_uart_1irq(3, MX21_UART4_BASE_ADDR, SZ_4K, MX21_INT_UART4, pdata) +extern const struct imx_imx_ssi_data imx21_imx_ssi_data[] __initconst; +#define imx21_add_imx_ssi(id, pdata) \ + imx_add_imx_ssi(&imx21_imx_ssi_data[id], pdata) +extern const struct imx_imx_uart_1irq_data imx21_imx_uart_data[] __initconst; +#define imx21_add_imx_uart(id, pdata) \ + imx_add_imx_uart_1irq(&imx21_imx_uart_data[id], pdata) +#define imx21_add_imx_uart0(pdata) imx21_add_imx_uart(0, pdata) +#define imx21_add_imx_uart1(pdata) imx21_add_imx_uart(1, pdata) +#define imx21_add_imx_uart2(pdata) imx21_add_imx_uart(2, pdata) +#define imx21_add_imx_uart3(pdata) imx21_add_imx_uart(3, pdata) + +extern const struct imx_mxc_nand_data imx21_mxc_nand_data __initconst; #define imx21_add_mxc_nand(pdata) \ - imx_add_mxc_nand_v1(MX21_NFC_BASE_ADDR, MX21_INT_NANDFC, pdata) + imx_add_mxc_nand(&imx21_mxc_nand_data, pdata) -#define imx21_add_spi_imx0(pdata) \ - imx_add_spi_imx(0, MX21_CSPI1_BASE_ADDR, SZ_4K, MX21_INT_CSPI1, pdata) -#define imx21_add_spi_imx1(pdata) \ - imx_add_spi_imx(1, MX21_CSPI2_BASE_ADDR, SZ_4K, MX21_INT_CSPI2, pdata) +extern const struct imx_spi_imx_data imx21_cspi_data[] __initconst; +#define imx21_add_cspi(id, pdata) \ + imx_add_spi_imx(&imx21_cspi_data[id], pdata) +#define imx21_add_spi_imx0(pdata) imx21_add_cspi(0, pdata) +#define imx21_add_spi_imx1(pdata) imx21_add_cspi(1, pdata) diff --git a/arch/arm/mach-imx/devices-imx27.h b/arch/arm/mach-imx/devices-imx27.h index 65e7bb7ec2e886..7011690364f270 100644 --- a/arch/arm/mach-imx/devices-imx27.h +++ b/arch/arm/mach-imx/devices-imx27.h @@ -9,30 +9,35 @@ #include #include -#define imx27_add_i2c_imx0(pdata) \ - imx_add_imx_i2c(0, MX27_I2C1_BASE_ADDR, SZ_4K, MX27_INT_I2C1, pdata) -#define imx27_add_i2c_imx1(pdata) \ - imx_add_imx_i2c(1, MX27_I2C2_BASE_ADDR, SZ_4K, MX27_INT_I2C2, pdata) +extern const struct imx_fec_data imx27_fec_data __initconst; +#define imx27_add_fec(pdata) \ + imx_add_fec(&imx27_fec_data, pdata) -#define imx27_add_imx_uart0(pdata) \ - imx_add_imx_uart_1irq(0, MX27_UART1_BASE_ADDR, SZ_4K, MX27_INT_UART1, pdata) -#define imx27_add_imx_uart1(pdata) \ - imx_add_imx_uart_1irq(1, MX27_UART2_BASE_ADDR, SZ_4K, MX27_INT_UART2, pdata) -#define imx27_add_imx_uart2(pdata) \ - imx_add_imx_uart_1irq(2, MX27_UART3_BASE_ADDR, SZ_4K, MX27_INT_UART3, pdata) -#define imx27_add_imx_uart3(pdata) \ - imx_add_imx_uart_1irq(3, MX27_UART4_BASE_ADDR, SZ_4K, MX27_INT_UART4, pdata) -#define imx27_add_imx_uart4(pdata) \ - imx_add_imx_uart_1irq(4, MX27_UART5_BASE_ADDR, SZ_4K, MX27_INT_UART5, pdata) -#define imx27_add_imx_uart5(pdata) \ - imx_add_imx_uart_1irq(5, MX27_UART6_BASE_ADDR, SZ_4K, MX27_INT_UART6, pdata) +extern const struct imx_imx_i2c_data imx27_imx_i2c_data[] __initconst; +#define imx27_add_imx_i2c(id, pdata) \ + imx_add_imx_i2c(&imx27_imx_i2c_data[id], pdata) +extern const struct imx_imx_ssi_data imx27_imx_ssi_data[] __initconst; +#define imx27_add_imx_ssi(id, pdata) \ + imx_add_imx_ssi(&imx27_imx_ssi_data[id], pdata) + +extern const struct imx_imx_uart_1irq_data imx27_imx_uart_data[] __initconst; +#define imx27_add_imx_uart(id, pdata) \ + imx_add_imx_uart_1irq(&imx27_imx_uart_data[id], pdata) +#define imx27_add_imx_uart0(pdata) imx27_add_imx_uart(0, pdata) +#define imx27_add_imx_uart1(pdata) imx27_add_imx_uart(1, pdata) +#define imx27_add_imx_uart2(pdata) imx27_add_imx_uart(2, pdata) +#define imx27_add_imx_uart3(pdata) imx27_add_imx_uart(3, pdata) +#define imx27_add_imx_uart4(pdata) imx27_add_imx_uart(4, pdata) +#define imx27_add_imx_uart5(pdata) imx27_add_imx_uart(5, pdata) + +extern const struct imx_mxc_nand_data imx27_mxc_nand_data __initconst; #define imx27_add_mxc_nand(pdata) \ - imx_add_mxc_nand_v1(MX27_NFC_BASE_ADDR, MX27_INT_NANDFC, pdata) + imx_add_mxc_nand(&imx27_mxc_nand_data, pdata) -#define imx27_add_spi_imx0(pdata) \ - imx_add_spi_imx(0, MX27_CSPI1_BASE_ADDR, SZ_4K, MX27_INT_CSPI1, pdata) -#define imx27_add_spi_imx1(pdata) \ - imx_add_spi_imx(1, MX27_CSPI2_BASE_ADDR, SZ_4K, MX27_INT_CSPI2, pdata) -#define imx27_add_spi_imx2(pdata) \ - imx_add_spi_imx(2, MX27_CSPI3_BASE_ADDR, SZ_4K, MX27_INT_CSPI3, pdata) +extern const struct imx_spi_imx_data imx27_cspi_data[] __initconst; +#define imx27_add_cspi(id, pdata) \ + imx_add_spi_imx(&imx27_cspi_data[id], pdata) +#define imx27_add_spi_imx0(pdata) imx27_add_cspi(0, pdata) +#define imx27_add_spi_imx1(pdata) imx27_add_cspi(1, pdata) +#define imx27_add_spi_imx2(pdata) imx27_add_cspi(2, pdata) diff --git a/arch/arm/mach-imx/devices.c b/arch/arm/mach-imx/devices.c index 9c271a752b84da..fba5047de8b1fd 100644 --- a/arch/arm/mach-imx/devices.c +++ b/arch/arm/mach-imx/devices.c @@ -314,27 +314,6 @@ struct platform_device mxc_fb_device = { }, }; -#ifdef CONFIG_MACH_MX27 -static struct resource mxc_fec_resources[] = { - { - .start = MX27_FEC_BASE_ADDR, - .end = MX27_FEC_BASE_ADDR + SZ_4K - 1, - .flags = IORESOURCE_MEM, - }, { - .start = MX27_INT_FEC, - .end = MX27_INT_FEC, - .flags = IORESOURCE_IRQ, - }, -}; - -struct platform_device mxc_fec_device = { - .name = "fec", - .id = 0, - .num_resources = ARRAY_SIZE(mxc_fec_resources), - .resource = mxc_fec_resources, -}; -#endif - static struct resource mxc_pwm_resources[] = { { .start = MX2x_PWM_BASE_ADDR, @@ -480,41 +459,6 @@ struct platform_device mxc_usbh2 = { }; #endif -#define DEFINE_IMX_SSI_DMARES(_name, ssin, suffix) \ - { \ - .name = _name, \ - .start = MX2x_DMA_REQ_SSI ## ssin ## _ ## suffix, \ - .end = MX2x_DMA_REQ_SSI ## ssin ## _ ## suffix, \ - .flags = IORESOURCE_DMA, \ - } - -#define DEFINE_IMX_SSI_DEVICE(n, ssin, baseaddr, irq) \ - static struct resource imx_ssi_resources ## n[] = { \ - { \ - .start = MX2x_SSI ## ssin ## _BASE_ADDR, \ - .end = MX2x_SSI ## ssin ## _BASE_ADDR + 0x6f, \ - .flags = IORESOURCE_MEM, \ - }, { \ - .start = MX2x_INT_SSI1, \ - .end = MX2x_INT_SSI1, \ - .flags = IORESOURCE_IRQ, \ - }, \ - DEFINE_IMX_SSI_DMARES("tx0", ssin, TX0), \ - DEFINE_IMX_SSI_DMARES("rx0", ssin, RX0), \ - DEFINE_IMX_SSI_DMARES("tx1", ssin, TX1), \ - DEFINE_IMX_SSI_DMARES("rx1", ssin, RX1), \ - }; \ - \ - struct platform_device imx_ssi_device ## n = { \ - .name = "imx-ssi", \ - .id = n, \ - .num_resources = ARRAY_SIZE(imx_ssi_resources ## n), \ - .resource = imx_ssi_resources ## n, \ - } - -DEFINE_IMX_SSI_DEVICE(0, 1, MX2x_SSI1_BASE_ADDR, MX2x_INT_SSI1); -DEFINE_IMX_SSI_DEVICE(1, 2, MX2x_SSI1_BASE_ADDR, MX2x_INT_SSI1); - /* GPIO port description */ #define DEFINE_MXC_GPIO_PORT_IRQ(SOC, n, _irq) \ { \ diff --git a/arch/arm/mach-imx/devices.h b/arch/arm/mach-imx/devices.h index efd4527506a5e6..807f02a031c945 100644 --- a/arch/arm/mach-imx/devices.h +++ b/arch/arm/mach-imx/devices.h @@ -16,7 +16,6 @@ extern struct platform_device mxc_gpt5; extern struct platform_device mxc_wdt; extern struct platform_device mxc_w1_master_device; extern struct platform_device mxc_fb_device; -extern struct platform_device mxc_fec_device; extern struct platform_device mxc_pwm_device; extern struct platform_device mxc_sdhc_device0; extern struct platform_device mxc_sdhc_device1; @@ -26,7 +25,5 @@ extern struct platform_device mxc_otg_host; extern struct platform_device mxc_usbh1; extern struct platform_device mxc_usbh2; extern struct platform_device mx21_usbhc_device; -extern struct platform_device imx_ssi_device0; -extern struct platform_device imx_ssi_device1; extern struct platform_device imx_kpp_device; #endif diff --git a/arch/arm/mach-imx/eukrea_mbimx27-baseboard.c b/arch/arm/mach-imx/eukrea_mbimx27-baseboard.c index 4edc5f43920109..026263c665cae0 100644 --- a/arch/arm/mach-imx/eukrea_mbimx27-baseboard.c +++ b/arch/arm/mach-imx/eukrea_mbimx27-baseboard.c @@ -36,13 +36,12 @@ #include #include #include -#include #include #include "devices-imx27.h" #include "devices.h" -static int eukrea_mbimx27_pins[] = { +static const int eukrea_mbimx27_pins[] __initconst = { /* UART2 */ PE3_PF_UART2_CTS, PE4_PF_UART2_RTS, @@ -311,7 +310,8 @@ static struct imxmmc_platform_data sdhc_pdata = { .dat3_card_detect = 1, }; -struct imx_ssi_platform_data eukrea_mbimx27_ssi_pdata = { +static const +struct imx_ssi_platform_data eukrea_mbimx27_ssi_pdata __initconst = { .flags = IMX_SSI_DMA | IMX_SSI_USE_I2S_SLAVE, }; @@ -357,7 +357,7 @@ void __init eukrea_mbimx27_baseboard_init(void) i2c_register_board_info(0, eukrea_mbimx27_i2c_devices, ARRAY_SIZE(eukrea_mbimx27_i2c_devices)); - mxc_register_device(&imx_ssi_device0, &eukrea_mbimx27_ssi_pdata); + imx27_add_imx_ssi(0, &eukrea_mbimx27_ssi_pdata); #if defined(CONFIG_TOUCHSCREEN_ADS7846) \ || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) diff --git a/arch/arm/mach-imx/mach-cpuimx27.c b/arch/arm/mach-imx/mach-cpuimx27.c index 6830afd1d2baf0..745ee60fb068fe 100644 --- a/arch/arm/mach-imx/mach-cpuimx27.c +++ b/arch/arm/mach-imx/mach-cpuimx27.c @@ -46,7 +46,7 @@ #include "devices-imx27.h" #include "devices.h" -static int eukrea_cpuimx27_pins[] = { +static const int eukrea_cpuimx27_pins[] __initconst = { /* UART1 */ PE12_PF_UART1_TXD, PE13_PF_UART1_RXD, @@ -157,7 +157,6 @@ cpuimx27_nand_board_info __initconst = { static struct platform_device *platform_devices[] __initdata = { &eukrea_cpuimx27_nor_mtd_device, - &mxc_fec_device, &mxc_wdt, &mxc_w1_master_device, }; @@ -259,8 +258,9 @@ static void __init eukrea_cpuimx27_init(void) i2c_register_board_info(0, eukrea_cpuimx27_i2c_devices, ARRAY_SIZE(eukrea_cpuimx27_i2c_devices)); - imx27_add_i2c_imx0(&cpuimx27_i2c1_data); + imx27_add_imx_i2c(0, &cpuimx27_i2c1_data); + imx27_add_fec(NULL); platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); #if defined(CONFIG_MACH_EUKREA_CPUIMX27_USESDHC2) @@ -307,8 +307,6 @@ static struct sys_timer eukrea_cpuimx27_timer = { }; MACHINE_START(CPUIMX27, "EUKREA CPUIMX27") - .phys_io = MX27_AIPI_BASE_ADDR, - .io_pg_offst = ((MX27_AIPI_BASE_ADDR_VIRT) >> 18) & 0xfffc, .boot_params = MX27_PHYS_OFFSET + 0x100, .map_io = mx27_map_io, .init_irq = mx27_init_irq, diff --git a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c new file mode 100644 index 00000000000000..59716fab586d99 --- /dev/null +++ b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c @@ -0,0 +1,261 @@ +/* + * mach-imx27_visstrim_m10.c + * + * Copyright 2010 Javier Martin + * + * Based on mach-pcm038.c, mach-pca100.c, mach-mx27ads.c and others. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "devices-imx27.h" +#include "devices.h" + +#define OTG_PHY_CS_GPIO (GPIO_PORTF + 17) +#define SDHC1_IRQ IRQ_GPIOB(25) + +static const int visstrim_m10_pins[] __initconst = { + /* UART1 (console) */ + PE12_PF_UART1_TXD, + PE13_PF_UART1_RXD, + PE14_PF_UART1_CTS, + PE15_PF_UART1_RTS, + /* FEC */ + PD0_AIN_FEC_TXD0, + PD1_AIN_FEC_TXD1, + PD2_AIN_FEC_TXD2, + PD3_AIN_FEC_TXD3, + PD4_AOUT_FEC_RX_ER, + PD5_AOUT_FEC_RXD1, + PD6_AOUT_FEC_RXD2, + PD7_AOUT_FEC_RXD3, + PD8_AF_FEC_MDIO, + PD9_AIN_FEC_MDC, + PD10_AOUT_FEC_CRS, + PD11_AOUT_FEC_TX_CLK, + PD12_AOUT_FEC_RXD0, + PD13_AOUT_FEC_RX_DV, + PD14_AOUT_FEC_RX_CLK, + PD15_AOUT_FEC_COL, + PD16_AIN_FEC_TX_ER, + PF23_AIN_FEC_TX_EN, + /* SDHC1 */ + PE18_PF_SD1_D0, + PE19_PF_SD1_D1, + PE20_PF_SD1_D2, + PE21_PF_SD1_D3, + PE22_PF_SD1_CMD, + PE23_PF_SD1_CLK, + /* Both I2Cs */ + PD17_PF_I2C_DATA, + PD18_PF_I2C_CLK, + PC5_PF_I2C2_SDA, + PC6_PF_I2C2_SCL, + /* USB OTG */ + OTG_PHY_CS_GPIO | GPIO_GPIO | GPIO_OUT, + PC9_PF_USBOTG_DATA0, + PC11_PF_USBOTG_DATA1, + PC10_PF_USBOTG_DATA2, + PC13_PF_USBOTG_DATA3, + PC12_PF_USBOTG_DATA4, + PC7_PF_USBOTG_DATA5, + PC8_PF_USBOTG_DATA6, + PE25_PF_USBOTG_DATA7, + PE24_PF_USBOTG_CLK, + PE2_PF_USBOTG_DIR, + PE0_PF_USBOTG_NXT, + PE1_PF_USBOTG_STP, + PB23_PF_USB_PWR, + PB24_PF_USB_OC, +}; + +/* GPIOs used as events for applications */ +static struct gpio_keys_button visstrim_gpio_keys[] = { + { + .type = EV_KEY, + .code = KEY_RESTART, + .gpio = (GPIO_PORTC + 15), + .desc = "Default config", + .active_low = 0, + .wakeup = 1, + }, + { + .type = EV_KEY, + .code = KEY_RECORD, + .gpio = (GPIO_PORTF + 14), + .desc = "Record", + .active_low = 0, + .wakeup = 1, + }, + { + .type = EV_KEY, + .code = KEY_STOP, + .gpio = (GPIO_PORTF + 13), + .desc = "Stop", + .active_low = 0, + .wakeup = 1, + } +}; + +static struct gpio_keys_platform_data visstrim_gpio_keys_platform_data = { + .buttons = visstrim_gpio_keys, + .nbuttons = ARRAY_SIZE(visstrim_gpio_keys), +}; + +static struct platform_device visstrim_gpio_keys_device = { + .name = "gpio-keys", + .id = -1, + .dev = { + .platform_data = &visstrim_gpio_keys_platform_data, + }, +}; + +/* Visstrim_SM10 has a microSD slot connected to sdhc1 */ +static int visstrim_m10_sdhc1_init(struct device *dev, + irq_handler_t detect_irq, void *data) +{ + int ret; + + ret = request_irq(SDHC1_IRQ, detect_irq, IRQF_TRIGGER_FALLING, + "mmc-detect", data); + return ret; +} + +static void visstrim_m10_sdhc1_exit(struct device *dev, void *data) +{ + free_irq(SDHC1_IRQ, data); +} + +static struct imxmmc_platform_data visstrim_m10_sdhc_pdata = { + .init = visstrim_m10_sdhc1_init, + .exit = visstrim_m10_sdhc1_exit, +}; + +/* Visstrim_SM10 NOR flash */ +static struct physmap_flash_data visstrim_m10_flash_data = { + .width = 2, +}; + +static struct resource visstrim_m10_flash_resource = { + .start = 0xc0000000, + .end = 0xc0000000 + SZ_64M - 1, + .flags = IORESOURCE_MEM, +}; + +static struct platform_device visstrim_m10_nor_mtd_device = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &visstrim_m10_flash_data, + }, + .num_resources = 1, + .resource = &visstrim_m10_flash_resource, +}; + +static struct platform_device *platform_devices[] __initdata = { + &visstrim_gpio_keys_device, + &visstrim_m10_nor_mtd_device, +}; + +/* Visstrim_M10 uses UART0 as console */ +static const struct imxuart_platform_data uart_pdata __initconst = { + .flags = IMXUART_HAVE_RTSCTS, +}; + +/* I2C */ +static const struct imxi2c_platform_data visstrim_m10_i2c_data __initconst = { + .bitrate = 100000, +}; + +static struct pca953x_platform_data visstrim_m10_pca9555_pdata = { + .gpio_base = 240, /* After MX27 internal GPIOs */ + .invert = 0, +}; + +static struct i2c_board_info visstrim_m10_i2c_devices[] = { + { + I2C_BOARD_INFO("pca9555", 0x20), + .platform_data = &visstrim_m10_pca9555_pdata, + }, +}; + +/* USB OTG */ +static int otg_phy_init(struct platform_device *pdev) +{ + gpio_set_value(OTG_PHY_CS_GPIO, 0); + return 0; +} + +static struct mxc_usbh_platform_data visstrim_m10_usbotg_pdata = { + .init = otg_phy_init, + .portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT, + .flags = MXC_EHCI_POWER_PINS_ENABLED, +}; + +static void __init visstrim_m10_board_init(void) +{ + int ret; + + ret = mxc_gpio_setup_multiple_pins(visstrim_m10_pins, + ARRAY_SIZE(visstrim_m10_pins), "VISSTRIM_M10"); + if (ret) + pr_err("Failed to setup pins (%d)\n", ret); + + imx27_add_imx_uart0(&uart_pdata); + + i2c_register_board_info(0, visstrim_m10_i2c_devices, + ARRAY_SIZE(visstrim_m10_i2c_devices)); + imx27_add_imx_i2c(0, &visstrim_m10_i2c_data); + imx27_add_imx_i2c(1, &visstrim_m10_i2c_data); + mxc_register_device(&mxc_sdhc_device0, &visstrim_m10_sdhc_pdata); + mxc_register_device(&mxc_otg_host, &visstrim_m10_usbotg_pdata); + imx27_add_fec(NULL); + platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); +} + +static void __init visstrim_m10_timer_init(void) +{ + mx27_clocks_init((unsigned long)25000000); +} + +static struct sys_timer visstrim_m10_timer = { + .init = visstrim_m10_timer_init, +}; + +MACHINE_START(IMX27_VISSTRIM_M10, "Vista Silicon Visstrim_M10") + .boot_params = MX27_PHYS_OFFSET + 0x100, + .map_io = mx27_map_io, + .init_irq = mx27_init_irq, + .init_machine = visstrim_m10_board_init, + .timer = &visstrim_m10_timer, +MACHINE_END diff --git a/arch/arm/mach-imx/mach-imx27lite.c b/arch/arm/mach-imx/mach-imx27lite.c index 22a2b5d9121365..bbdbc75127d3fd 100644 --- a/arch/arm/mach-imx/mach-imx27lite.c +++ b/arch/arm/mach-imx/mach-imx27lite.c @@ -27,7 +27,7 @@ #include "devices-imx27.h" #include "devices.h" -static unsigned int mx27lite_pins[] = { +static const int mx27lite_pins[] __initconst = { /* UART1 */ PE12_PF_UART1_TXD, PE13_PF_UART1_RXD, @@ -58,16 +58,12 @@ static const struct imxuart_platform_data uart_pdata __initconst = { .flags = IMXUART_HAVE_RTSCTS, }; -static struct platform_device *platform_devices[] __initdata = { - &mxc_fec_device, -}; - static void __init mx27lite_init(void) { mxc_gpio_setup_multiple_pins(mx27lite_pins, ARRAY_SIZE(mx27lite_pins), "imx27lite"); imx27_add_imx_uart0(&uart_pdata); - platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); + imx27_add_fec(NULL); } static void __init mx27lite_timer_init(void) @@ -80,8 +76,6 @@ static struct sys_timer mx27lite_timer = { }; MACHINE_START(IMX27LITE, "LogicPD i.MX27LITE") - .phys_io = MX27_AIPI_BASE_ADDR, - .io_pg_offst = ((MX27_AIPI_BASE_ADDR_VIRT) >> 18) & 0xfffc, .boot_params = MX27_PHYS_OFFSET + 0x100, .map_io = mx27_map_io, .init_irq = mx27_init_irq, diff --git a/arch/arm/mach-imx/mach-mx1ads.c b/arch/arm/mach-imx/mach-mx1ads.c index 77a760cfadc026..6187ce9ba7d541 100644 --- a/arch/arm/mach-imx/mach-mx1ads.c +++ b/arch/arm/mach-imx/mach-mx1ads.c @@ -32,7 +32,7 @@ #include "devices-imx1.h" #include "devices.h" -static int mx1ads_pins[] = { +static const int mx1ads_pins[] __initconst = { /* UART1 */ PC9_PF_UART1_CTS, PC10_PF_UART1_RTS, @@ -131,7 +131,7 @@ static void __init mx1ads_init(void) i2c_register_board_info(0, mx1ads_i2c_devices, ARRAY_SIZE(mx1ads_i2c_devices)); - imx1_add_i2c_imx(&mx1ads_i2c_data); + imx1_add_imx_i2c(&mx1ads_i2c_data); } static void __init mx1ads_timer_init(void) @@ -145,8 +145,6 @@ struct sys_timer mx1ads_timer = { MACHINE_START(MX1ADS, "Freescale MX1ADS") /* Maintainer: Sascha Hauer, Pengutronix */ - .phys_io = MX1_IO_BASE_ADDR, - .io_pg_offst = (MX1_IO_BASE_ADDR_VIRT >> 18) & 0xfffc, .boot_params = MX1_PHYS_OFFSET + 0x100, .map_io = mx1_map_io, .init_irq = mx1_init_irq, @@ -155,8 +153,6 @@ MACHINE_START(MX1ADS, "Freescale MX1ADS") MACHINE_END MACHINE_START(MXLADS, "Freescale MXLADS") - .phys_io = MX1_IO_BASE_ADDR, - .io_pg_offst = (MX1_IO_BASE_ADDR_VIRT >> 18) & 0xfffc, .boot_params = MX1_PHYS_OFFSET + 0x100, .map_io = mx1_map_io, .init_irq = mx1_init_irq, diff --git a/arch/arm/mach-imx/mach-mx21ads.c b/arch/arm/mach-imx/mach-mx21ads.c index 96d7f8189f3253..e1282e9f50ffe3 100644 --- a/arch/arm/mach-imx/mach-mx21ads.c +++ b/arch/arm/mach-imx/mach-mx21ads.c @@ -67,7 +67,7 @@ #define MX21ADS_IO_LED4_ON 0x4000 #define MX21ADS_IO_LED3_ON 0x8000 -static unsigned int mx21ads_pins[] = { +static const int mx21ads_pins[] __initconst = { /* CS8900A */ (GPIO_PORTE | GPIO_GPIO | GPIO_IN | 11), @@ -314,8 +314,6 @@ static struct sys_timer mx21ads_timer = { MACHINE_START(MX21ADS, "Freescale i.MX21ADS") /* maintainer: Freescale Semiconductor, Inc. */ - .phys_io = MX21_AIPI_BASE_ADDR, - .io_pg_offst = ((MX21_AIPI_BASE_ADDR_VIRT) >> 18) & 0xfffc, .boot_params = MX21_PHYS_OFFSET + 0x100, .map_io = mx21ads_map_io, .init_irq = mx21_init_irq, diff --git a/arch/arm/mach-imx/mach-mx27_3ds.c b/arch/arm/mach-imx/mach-mx27_3ds.c index e66ffaa1c26c26..b8bbd31aa850c4 100644 --- a/arch/arm/mach-imx/mach-mx27_3ds.c +++ b/arch/arm/mach-imx/mach-mx27_3ds.c @@ -33,7 +33,7 @@ #include "devices-imx27.h" #include "devices.h" -static unsigned int mx27pdk_pins[] = { +static const int mx27pdk_pins[] __initconst = { /* UART1 */ PE12_PF_UART1_TXD, PE13_PF_UART1_RXD, @@ -64,10 +64,6 @@ static const struct imxuart_platform_data uart_pdata __initconst = { .flags = IMXUART_HAVE_RTSCTS, }; -static struct platform_device *platform_devices[] __initdata = { - &mxc_fec_device, -}; - /* * Matrix keyboard */ @@ -94,7 +90,7 @@ static void __init mx27pdk_init(void) mxc_gpio_setup_multiple_pins(mx27pdk_pins, ARRAY_SIZE(mx27pdk_pins), "mx27pdk"); imx27_add_imx_uart0(&uart_pdata); - platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); + imx27_add_fec(NULL); mxc_register_device(&imx_kpp_device, &mx27_3ds_keymap_data); } @@ -109,8 +105,6 @@ static struct sys_timer mx27pdk_timer = { MACHINE_START(MX27_3DS, "Freescale MX27PDK") /* maintainer: Freescale Semiconductor, Inc. */ - .phys_io = MX27_AIPI_BASE_ADDR, - .io_pg_offst = ((MX27_AIPI_BASE_ADDR_VIRT) >> 18) & 0xfffc, .boot_params = MX27_PHYS_OFFSET + 0x100, .map_io = mx27_map_io, .init_irq = mx27_init_irq, diff --git a/arch/arm/mach-imx/mach-mx27ads.c b/arch/arm/mach-imx/mach-mx27ads.c index 9c77da98a10eec..a1e4bc573afc20 100644 --- a/arch/arm/mach-imx/mach-mx27ads.c +++ b/arch/arm/mach-imx/mach-mx27ads.c @@ -66,7 +66,7 @@ /* to determine the correct external crystal reference */ #define CKIH_27MHZ_BIT_SET (1 << 3) -static unsigned int mx27ads_pins[] = { +static const int mx27ads_pins[] __initconst = { /* UART0 */ PE12_PF_UART1_TXD, PE13_PF_UART1_RXD, @@ -284,7 +284,6 @@ static struct imxmmc_platform_data sdhc2_pdata = { static struct platform_device *platform_devices[] __initdata = { &mx27ads_nor_mtd_device, - &mxc_fec_device, &mxc_w1_master_device, }; @@ -308,11 +307,12 @@ static void __init mx27ads_board_init(void) /* only the i2c master 1 is used on this CPU card */ i2c_register_board_info(1, mx27ads_i2c_devices, ARRAY_SIZE(mx27ads_i2c_devices)); - imx27_add_i2c_imx1(&mx27ads_i2c1_data); + imx27_add_imx_i2c(1, &mx27ads_i2c1_data); mxc_register_device(&mxc_fb_device, &mx27ads_fb_data); mxc_register_device(&mxc_sdhc_device0, &sdhc1_pdata); mxc_register_device(&mxc_sdhc_device1, &sdhc2_pdata); + imx27_add_fec(NULL); platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); } @@ -347,8 +347,6 @@ static void __init mx27ads_map_io(void) MACHINE_START(MX27ADS, "Freescale i.MX27ADS") /* maintainer: Freescale Semiconductor, Inc. */ - .phys_io = MX27_AIPI_BASE_ADDR, - .io_pg_offst = ((MX27_AIPI_BASE_ADDR_VIRT) >> 18) & 0xfffc, .boot_params = MX27_PHYS_OFFSET + 0x100, .map_io = mx27ads_map_io, .init_irq = mx27_init_irq, diff --git a/arch/arm/mach-imx/mach-mxt_td60.c b/arch/arm/mach-imx/mach-mxt_td60.c index a3a1e452d4c5a1..38d3a4ae17c765 100644 --- a/arch/arm/mach-imx/mach-mxt_td60.c +++ b/arch/arm/mach-imx/mach-mxt_td60.c @@ -37,7 +37,7 @@ #include "devices-imx27.h" #include "devices.h" -static unsigned int mxt_td60_pins[] __initdata = { +static const int mxt_td60_pins[] __initconst = { /* UART0 */ PE12_PF_UART1_TXD, PE13_PF_UART1_RXD, @@ -231,10 +231,6 @@ static struct imxmmc_platform_data sdhc1_pdata = { .exit = mxt_td60_sdhc1_exit, }; -static struct platform_device *platform_devices[] __initdata = { - &mxc_fec_device, -}; - static const struct imxuart_platform_data uart_pdata __initconst = { .flags = IMXUART_HAVE_RTSCTS, }; @@ -255,12 +251,11 @@ static void __init mxt_td60_board_init(void) i2c_register_board_info(1, mxt_td60_i2c2_devices, ARRAY_SIZE(mxt_td60_i2c2_devices)); - imx27_add_i2c_imx0(&mxt_td60_i2c0_data); - imx27_add_i2c_imx1(&mxt_td60_i2c1_data); + imx27_add_imx_i2c(0, &mxt_td60_i2c0_data); + imx27_add_imx_i2c(1, &mxt_td60_i2c1_data); mxc_register_device(&mxc_fb_device, &mxt_td60_fb_data); mxc_register_device(&mxc_sdhc_device0, &sdhc1_pdata); - - platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); + imx27_add_fec(NULL); } static void __init mxt_td60_timer_init(void) @@ -274,8 +269,6 @@ static struct sys_timer mxt_td60_timer = { MACHINE_START(MXT_TD60, "Maxtrack i-MXT TD60") /* maintainer: Maxtrack Industrial */ - .phys_io = MX27_AIPI_BASE_ADDR, - .io_pg_offst = ((MX27_AIPI_BASE_ADDR_VIRT) >> 18) & 0xfffc, .boot_params = MX27_PHYS_OFFSET + 0x100, .map_io = mx27_map_io, .init_irq = mx27_init_irq, diff --git a/arch/arm/mach-imx/mach-pca100.c b/arch/arm/mach-imx/mach-pca100.c index 23c9e1f37b9c02..8c720d44602ab1 100644 --- a/arch/arm/mach-imx/mach-pca100.c +++ b/arch/arm/mach-imx/mach-pca100.c @@ -38,7 +38,6 @@ #include #include #include -#include #include #include #include @@ -55,7 +54,7 @@ #define SPI1_SS1 (GPIO_PORTD + 27) #define SD2_CD (GPIO_PORTC + 29) -static int pca100_pins[] = { +static const int pca100_pins[] __initconst = { /* UART1 */ PE12_PF_UART1_TXD, PE13_PF_UART1_RXD, @@ -174,7 +173,6 @@ pca100_nand_board_info __initconst = { static struct platform_device *platform_devices[] __initdata = { &mxc_w1_master_device, - &mxc_fec_device, &mxc_wdt, }; @@ -193,11 +191,9 @@ static struct i2c_board_info pca100_i2c_devices[] = { I2C_BOARD_INFO("at24", 0x52), /* E0=0, E1=1, E2=0 */ .platform_data = &board_eeprom, }, { - I2C_BOARD_INFO("rtc-pcf8563", 0x51), - .type = "pcf8563" + I2C_BOARD_INFO("pcf8563", 0x51), }, { I2C_BOARD_INFO("lm75", 0x4a), - .type = "lm75" } }; @@ -252,7 +248,7 @@ static void pca100_ac97_cold_reset(struct snd_ac97 *ac97) msleep(2); } -static struct imx_ssi_platform_data pca100_ssi_pdata = { +static const struct imx_ssi_platform_data pca100_ssi_pdata __initconst = { .ac97_reset = pca100_ac97_cold_reset, .ac97_warm_reset = pca100_ac97_warm_reset, .flags = IMX_SSI_USE_AC97, @@ -389,7 +385,7 @@ static void __init pca100_init(void) if (ret) printk(KERN_ERR "pca100: Failed to setup pins (%d)\n", ret); - mxc_register_device(&imx_ssi_device0, &pca100_ssi_pdata); + imx27_add_imx_ssi(0, &pca100_ssi_pdata); imx27_add_imx_uart0(&uart_pdata); @@ -401,7 +397,7 @@ static void __init pca100_init(void) i2c_register_board_info(1, pca100_i2c_devices, ARRAY_SIZE(pca100_i2c_devices)); - imx27_add_i2c_imx1(&pca100_i2c1_data); + imx27_add_imx_i2c(1, &pca100_i2c1_data); #if defined(CONFIG_SPI_IMX) || defined(CONFIG_SPI_IMX_MODULE) mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_IN); @@ -436,6 +432,7 @@ static void __init pca100_init(void) mxc_register_device(&mxc_fb_device, &pca100_fb_data); + imx27_add_fec(NULL); platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); } @@ -449,8 +446,6 @@ static struct sys_timer pca100_timer = { }; MACHINE_START(PCA100, "phyCARD-i.MX27") - .phys_io = MX27_AIPI_BASE_ADDR, - .io_pg_offst = ((MX27_AIPI_BASE_ADDR_VIRT) >> 18) & 0xfffc, .boot_params = MX27_PHYS_OFFSET + 0x100, .map_io = mx27_map_io, .init_irq = mx27_init_irq, diff --git a/arch/arm/mach-imx/mach-pcm038.c b/arch/arm/mach-imx/mach-pcm038.c index 9212e8f37001d0..49a97ce0742665 100644 --- a/arch/arm/mach-imx/mach-pcm038.c +++ b/arch/arm/mach-imx/mach-pcm038.c @@ -43,7 +43,7 @@ #include "devices-imx27.h" #include "devices.h" -static int pcm038_pins[] = { +static const int pcm038_pins[] __initconst = { /* UART1 */ PE12_PF_UART1_TXD, PE13_PF_UART1_RXD, @@ -173,7 +173,6 @@ pcm038_nand_board_info __initconst = { static struct platform_device *platform_devices[] __initdata = { &pcm038_nor_mtd_device, &mxc_w1_master_device, - &mxc_fec_device, &pcm038_sram_mtd_device, &mxc_wdt, }; @@ -257,7 +256,7 @@ static struct regulator_init_data cam_data = { .consumer_supplies = cam_consumers, }; -struct mc13783_regulator_init_data pcm038_regulators[] = { +static struct mc13783_regulator_init_data pcm038_regulators[] = { { .id = MC13783_REGU_VCAM, .init_data = &cam_data, @@ -309,7 +308,7 @@ static void __init pcm038_init(void) i2c_register_board_info(1, pcm038_i2c_devices, ARRAY_SIZE(pcm038_i2c_devices)); - imx27_add_i2c_imx1(&pcm038_i2c1_data); + imx27_add_imx_i2c(1, &pcm038_i2c1_data); /* PE18 for user-LED D40 */ mxc_gpio_mode(GPIO_PORTE | 18 | GPIO_GPIO | GPIO_OUT); @@ -325,6 +324,7 @@ static void __init pcm038_init(void) mxc_register_device(&mxc_usbh2, &usbh2_pdata); + imx27_add_fec(NULL); platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); #ifdef CONFIG_MACH_PCM970_BASEBOARD @@ -342,8 +342,6 @@ static struct sys_timer pcm038_timer = { }; MACHINE_START(PCM038, "phyCORE-i.MX27") - .phys_io = MX27_AIPI_BASE_ADDR, - .io_pg_offst = ((MX27_AIPI_BASE_ADDR_VIRT) >> 18) & 0xfffc, .boot_params = MX27_PHYS_OFFSET + 0x100, .map_io = mx27_map_io, .init_irq = mx27_init_irq, diff --git a/arch/arm/mach-imx/mach-scb9328.c b/arch/arm/mach-imx/mach-scb9328.c index 88bf0d1e26e6eb..1fbdd3faa7abf5 100644 --- a/arch/arm/mach-imx/mach-scb9328.c +++ b/arch/arm/mach-imx/mach-scb9328.c @@ -95,7 +95,7 @@ static struct platform_device dm9000x_device = { } }; -static int mxc_uart1_pins[] = { +static const int mxc_uart1_pins[] = { PC9_PF_UART1_CTS, PC10_PF_UART1_RTS, PC11_PF_UART1_TXD, @@ -147,8 +147,6 @@ static struct sys_timer scb9328_timer = { MACHINE_START(SCB9328, "Synertronixx scb9328") /* Sascha Hauer */ - .phys_io = 0x00200000, - .io_pg_offst = ((0xe0200000) >> 18) & 0xfffc, .boot_params = 0x08000100, .map_io = mx1_map_io, .init_irq = mx1_init_irq, diff --git a/arch/arm/mach-imx/pcm970-baseboard.c b/arch/arm/mach-imx/pcm970-baseboard.c index f490a406d57e73..9110d9cca7a2dc 100644 --- a/arch/arm/mach-imx/pcm970-baseboard.c +++ b/arch/arm/mach-imx/pcm970-baseboard.c @@ -31,7 +31,7 @@ #include "devices.h" -static int pcm970_pins[] = { +static const int pcm970_pins[] __initconst = { /* SDHC */ PB4_PF_SD2_D0, PB5_PF_SD2_D1, @@ -200,7 +200,7 @@ static struct resource pcm970_sja1000_resources[] = { }, }; -struct sja1000_platform_data pcm970_sja1000_platform_data = { +static struct sja1000_platform_data pcm970_sja1000_platform_data = { .osc_freq = 16000000, .ocr = OCR_TX1_PULLDOWN | OCR_TX0_PUSHPULL, .cdr = CDR_CBP, diff --git a/arch/arm/mach-integrator/include/mach/debug-macro.S b/arch/arm/mach-integrator/include/mach/debug-macro.S index 87a6888ae011ba..a1f598fd3a5672 100644 --- a/arch/arm/mach-integrator/include/mach/debug-macro.S +++ b/arch/arm/mach-integrator/include/mach/debug-macro.S @@ -11,12 +11,10 @@ * */ - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - moveq \rx, #0x16000000 @ physical base address - movne \rx, #0xf0000000 @ virtual base - addne \rx, \rx, #0x16000000 >> 4 + .macro addruart, rp, rv + mov \rp, #0x16000000 @ physical base address + mov \rv, #0xf0000000 @ virtual base + add \rv, \rv, #0x16000000 >> 4 .endm #include diff --git a/arch/arm/mach-integrator/include/mach/vmalloc.h b/arch/arm/mach-integrator/include/mach/vmalloc.h index e87ab0b37bddb3..e056e7cf5645f8 100644 --- a/arch/arm/mach-integrator/include/mach/vmalloc.h +++ b/arch/arm/mach-integrator/include/mach/vmalloc.h @@ -17,4 +17,4 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ -#define VMALLOC_END (PAGE_OFFSET + 0x10000000) +#define VMALLOC_END 0xd0000000 diff --git a/arch/arm/mach-integrator/integrator_ap.c b/arch/arm/mach-integrator/integrator_ap.c index 6ab5a03ab9d8b0..548208f11179c0 100644 --- a/arch/arm/mach-integrator/integrator_ap.c +++ b/arch/arm/mach-integrator/integrator_ap.c @@ -500,8 +500,6 @@ static struct sys_timer ap_timer = { MACHINE_START(INTEGRATOR, "ARM-Integrator") /* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */ - .phys_io = 0x16000000, - .io_pg_offst = ((0xf1600000) >> 18) & 0xfffc, .boot_params = 0x00000100, .map_io = ap_map_io, .reserve = integrator_reserve, diff --git a/arch/arm/mach-integrator/integrator_cp.c b/arch/arm/mach-integrator/integrator_cp.c index 05db40e3c4f75a..6258c90d020c30 100644 --- a/arch/arm/mach-integrator/integrator_cp.c +++ b/arch/arm/mach-integrator/integrator_cp.c @@ -599,8 +599,6 @@ static struct sys_timer cp_timer = { MACHINE_START(CINTEGRATOR, "ARM-IntegratorCP") /* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */ - .phys_io = 0x16000000, - .io_pg_offst = ((0xf1600000) >> 18) & 0xfffc, .boot_params = 0x00000100, .map_io = intcp_map_io, .reserve = integrator_reserve, diff --git a/arch/arm/mach-iop13xx/include/mach/debug-macro.S b/arch/arm/mach-iop13xx/include/mach/debug-macro.S index c9d6ba46963da9..e664466d51bf47 100644 --- a/arch/arm/mach-iop13xx/include/mach/debug-macro.S +++ b/arch/arm/mach-iop13xx/include/mach/debug-macro.S @@ -11,15 +11,13 @@ * published by the Free Software Foundation. */ - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ mmu enabled? - moveq \rx, #0xff000000 @ physical - orreq \rx, \rx, #0x00d80000 - movne \rx, #0xfe000000 @ virtual - orrne \rx, \rx, #0x00e80000 - orr \rx, \rx, #0x00002300 - orr \rx, \rx, #0x00000040 + .macro addruart, rp, rv + mov \rp, #0x00002300 + orr \rp, \rp, #0x00000040 + orr \rv, \rp, #0xfe000000 @ virtual + orr \rv, \rv, #0x00e80000 + orr \rp, \rp, #0xff000000 @ physical + orr \rp, \rp, #0x00d80000 .endm #define UART_SHIFT 2 diff --git a/arch/arm/mach-iop13xx/iq81340mc.c b/arch/arm/mach-iop13xx/iq81340mc.c index f91f3154577df1..9b5a63f5d07d43 100644 --- a/arch/arm/mach-iop13xx/iq81340mc.c +++ b/arch/arm/mach-iop13xx/iq81340mc.c @@ -91,8 +91,6 @@ static struct sys_timer iq81340mc_timer = { MACHINE_START(IQ81340MC, "Intel IQ81340MC") /* Maintainer: Dan Williams */ - .phys_io = IOP13XX_PMMR_PHYS_MEM_BASE, - .io_pg_offst = (IOP13XX_PMMR_VIRT_MEM_BASE >> 18) & 0xfffc, .boot_params = 0x00000100, .map_io = iop13xx_map_io, .init_irq = iop13xx_init_irq, diff --git a/arch/arm/mach-iop13xx/iq81340sc.c b/arch/arm/mach-iop13xx/iq81340sc.c index ddb7a3435de9e9..df3492a9c280e2 100644 --- a/arch/arm/mach-iop13xx/iq81340sc.c +++ b/arch/arm/mach-iop13xx/iq81340sc.c @@ -93,8 +93,6 @@ static struct sys_timer iq81340sc_timer = { MACHINE_START(IQ81340SC, "Intel IQ81340SC") /* Maintainer: Dan Williams */ - .phys_io = IOP13XX_PMMR_PHYS_MEM_BASE, - .io_pg_offst = (IOP13XX_PMMR_VIRT_MEM_BASE >> 18) & 0xfffc, .boot_params = 0x00000100, .map_io = iop13xx_map_io, .init_irq = iop13xx_init_irq, diff --git a/arch/arm/mach-iop32x/em7210.c b/arch/arm/mach-iop32x/em7210.c index 2bef9b6e1cc917..779f924af302d6 100644 --- a/arch/arm/mach-iop32x/em7210.c +++ b/arch/arm/mach-iop32x/em7210.c @@ -203,8 +203,6 @@ static void __init em7210_init_machine(void) } MACHINE_START(EM7210, "Lanner EM7210") - .phys_io = IQ31244_UART, - .io_pg_offst = ((IQ31244_UART) >> 18) & 0xfffc, .boot_params = 0xa0000100, .map_io = em7210_map_io, .init_irq = iop32x_init_irq, diff --git a/arch/arm/mach-iop32x/glantank.c b/arch/arm/mach-iop32x/glantank.c index 10384fc37cb29d..c6b6f9c5650d11 100644 --- a/arch/arm/mach-iop32x/glantank.c +++ b/arch/arm/mach-iop32x/glantank.c @@ -207,8 +207,6 @@ static void __init glantank_init_machine(void) MACHINE_START(GLANTANK, "GLAN Tank") /* Maintainer: Lennert Buytenhek */ - .phys_io = GLANTANK_UART, - .io_pg_offst = ((GLANTANK_UART) >> 18) & 0xfffc, .boot_params = 0xa0000100, .map_io = glantank_map_io, .init_irq = iop32x_init_irq, diff --git a/arch/arm/mach-iop32x/include/mach/debug-macro.S b/arch/arm/mach-iop32x/include/mach/debug-macro.S index 736afe1edd1f66..ff9e76c09f35b2 100644 --- a/arch/arm/mach-iop32x/include/mach/debug-macro.S +++ b/arch/arm/mach-iop32x/include/mach/debug-macro.S @@ -11,9 +11,10 @@ * published by the Free Software Foundation. */ - .macro addruart, rx, tmp - mov \rx, #0xfe000000 @ physical as well as virtual - orr \rx, \rx, #0x00800000 @ location of the UART + .macro addruart, rp, rv + mov \rp, #0xfe000000 @ physical as well as virtual + orr \rp, \rp, #0x00800000 @ location of the UART + mov \rv, \rp .endm #define UART_SHIFT 0 diff --git a/arch/arm/mach-iop32x/iq31244.c b/arch/arm/mach-iop32x/iq31244.c index d6ac85ff109dee..fde962c057f0e8 100644 --- a/arch/arm/mach-iop32x/iq31244.c +++ b/arch/arm/mach-iop32x/iq31244.c @@ -313,8 +313,6 @@ __setup("force_ep80219", force_ep80219_setup); MACHINE_START(IQ31244, "Intel IQ31244") /* Maintainer: Intel Corp. */ - .phys_io = IQ31244_UART, - .io_pg_offst = ((IQ31244_UART) >> 18) & 0xfffc, .boot_params = 0xa0000100, .map_io = iq31244_map_io, .init_irq = iop32x_init_irq, @@ -329,8 +327,6 @@ MACHINE_END */ MACHINE_START(EP80219, "Intel EP80219") /* Maintainer: Intel Corp. */ - .phys_io = IQ31244_UART, - .io_pg_offst = ((IQ31244_UART) >> 18) & 0xfffc, .boot_params = 0xa0000100, .map_io = iq31244_map_io, .init_irq = iop32x_init_irq, diff --git a/arch/arm/mach-iop32x/iq80321.c b/arch/arm/mach-iop32x/iq80321.c index c6a0e4ee9d911d..3a95950e8737a0 100644 --- a/arch/arm/mach-iop32x/iq80321.c +++ b/arch/arm/mach-iop32x/iq80321.c @@ -186,8 +186,6 @@ static void __init iq80321_init_machine(void) MACHINE_START(IQ80321, "Intel IQ80321") /* Maintainer: Intel Corp. */ - .phys_io = IQ80321_UART, - .io_pg_offst = ((IQ80321_UART) >> 18) & 0xfffc, .boot_params = 0xa0000100, .map_io = iq80321_map_io, .init_irq = iop32x_init_irq, diff --git a/arch/arm/mach-iop32x/n2100.c b/arch/arm/mach-iop32x/n2100.c index f108a31afc2b9f..626aa375915dcf 100644 --- a/arch/arm/mach-iop32x/n2100.c +++ b/arch/arm/mach-iop32x/n2100.c @@ -327,8 +327,6 @@ static void __init n2100_init_machine(void) MACHINE_START(N2100, "Thecus N2100") /* Maintainer: Lennert Buytenhek */ - .phys_io = N2100_UART, - .io_pg_offst = ((N2100_UART) >> 18) & 0xfffc, .boot_params = 0xa0000100, .map_io = n2100_map_io, .init_irq = iop32x_init_irq, diff --git a/arch/arm/mach-iop33x/include/mach/debug-macro.S b/arch/arm/mach-iop33x/include/mach/debug-macro.S index addb2da78422b0..40c500dd1fac61 100644 --- a/arch/arm/mach-iop33x/include/mach/debug-macro.S +++ b/arch/arm/mach-iop33x/include/mach/debug-macro.S @@ -11,13 +11,11 @@ * published by the Free Software Foundation. */ - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ mmu enabled? - moveq \rx, #0xff000000 @ physical - movne \rx, #0xfe000000 @ virtual - orr \rx, \rx, #0x00ff0000 - orr \rx, \rx, #0x0000f700 + .macro addruart, rp, rv + mov \rp, #0x00ff0000 + orr \rp, \rp, #0x0000f700 + orr \rv, #0xfe000000 @ virtual + orr \rp, #0xff000000 @ physical .endm #define UART_SHIFT 2 diff --git a/arch/arm/mach-iop33x/iq80331.c b/arch/arm/mach-iop33x/iq80331.c index c6ff5523b380f9..c565f8d1e3a468 100644 --- a/arch/arm/mach-iop33x/iq80331.c +++ b/arch/arm/mach-iop33x/iq80331.c @@ -141,8 +141,6 @@ static void __init iq80331_init_machine(void) MACHINE_START(IQ80331, "Intel IQ80331") /* Maintainer: Intel Corp. */ - .phys_io = 0xfefff000, - .io_pg_offst = ((0xfffff000) >> 18) & 0xfffc, .boot_params = 0x00000100, .map_io = iop3xx_map_io, .init_irq = iop33x_init_irq, diff --git a/arch/arm/mach-iop33x/iq80332.c b/arch/arm/mach-iop33x/iq80332.c index fbf55140939407..36a9efb254c25e 100644 --- a/arch/arm/mach-iop33x/iq80332.c +++ b/arch/arm/mach-iop33x/iq80332.c @@ -141,8 +141,6 @@ static void __init iq80332_init_machine(void) MACHINE_START(IQ80332, "Intel IQ80332") /* Maintainer: Intel Corp. */ - .phys_io = 0xfefff000, - .io_pg_offst = ((0xfffff000) >> 18) & 0xfffc, .boot_params = 0x00000100, .map_io = iop3xx_map_io, .init_irq = iop33x_init_irq, diff --git a/arch/arm/mach-ixp2000/enp2611.c b/arch/arm/mach-ixp2000/enp2611.c index 1a557e0d055b56..88663ab1d2ad94 100644 --- a/arch/arm/mach-ixp2000/enp2611.c +++ b/arch/arm/mach-ixp2000/enp2611.c @@ -253,8 +253,6 @@ static void __init enp2611_init_machine(void) MACHINE_START(ENP2611, "Radisys ENP-2611 PCI network processor board") /* Maintainer: Lennert Buytenhek */ - .phys_io = IXP2000_UART_PHYS_BASE, - .io_pg_offst = ((IXP2000_UART_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .map_io = enp2611_map_io, .init_irq = ixp2000_init_irq, diff --git a/arch/arm/mach-ixp2000/include/mach/debug-macro.S b/arch/arm/mach-ixp2000/include/mach/debug-macro.S index 6a827681680fe2..0ef533b2097213 100644 --- a/arch/arm/mach-ixp2000/include/mach/debug-macro.S +++ b/arch/arm/mach-ixp2000/include/mach/debug-macro.S @@ -11,16 +11,14 @@ * */ - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - moveq \rx, #0xc0000000 @ Physical base - movne \rx, #0xfe000000 @ virtual base - orrne \rx, \rx, #0x00f00000 - orr \rx, \rx, #0x00030000 + .macro addruart, rp, rv + mov \rp, #0x00030000 #ifdef __ARMEB__ - orr \rx, \rx, #0x00000003 + orr \rp, \rp, #0x00000003 #endif + orr \rv, \rp, #0xfe000000 @ virtual base + orr \rv, \rv, #0x00f00000 + orr \rp, \rp, #0xc0000000 @ Physical base .endm #define UART_SHIFT 2 diff --git a/arch/arm/mach-ixp2000/ixdp2400.c b/arch/arm/mach-ixp2000/ixdp2400.c index 55e5c69352ad4d..dfffc1e817faaa 100644 --- a/arch/arm/mach-ixp2000/ixdp2400.c +++ b/arch/arm/mach-ixp2000/ixdp2400.c @@ -170,8 +170,6 @@ void __init ixdp2400_init_irq(void) MACHINE_START(IXDP2400, "Intel IXDP2400 Development Platform") /* Maintainer: MontaVista Software, Inc. */ - .phys_io = IXP2000_UART_PHYS_BASE, - .io_pg_offst = ((IXP2000_UART_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .map_io = ixdp2x00_map_io, .init_irq = ixdp2400_init_irq, diff --git a/arch/arm/mach-ixp2000/ixdp2800.c b/arch/arm/mach-ixp2000/ixdp2800.c index 237b61a85e9a39..cd4c9bcff2b512 100644 --- a/arch/arm/mach-ixp2000/ixdp2800.c +++ b/arch/arm/mach-ixp2000/ixdp2800.c @@ -285,8 +285,6 @@ void __init ixdp2800_init_irq(void) MACHINE_START(IXDP2800, "Intel IXDP2800 Development Platform") /* Maintainer: MontaVista Software, Inc. */ - .phys_io = IXP2000_UART_PHYS_BASE, - .io_pg_offst = ((IXP2000_UART_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .map_io = ixdp2x00_map_io, .init_irq = ixdp2800_init_irq, diff --git a/arch/arm/mach-ixp2000/ixdp2x01.c b/arch/arm/mach-ixp2000/ixdp2x01.c index 0369ec4242a687..6c121bdbe31192 100644 --- a/arch/arm/mach-ixp2000/ixdp2x01.c +++ b/arch/arm/mach-ixp2000/ixdp2x01.c @@ -416,8 +416,6 @@ static void __init ixdp2x01_init_machine(void) #ifdef CONFIG_ARCH_IXDP2401 MACHINE_START(IXDP2401, "Intel IXDP2401 Development Platform") /* Maintainer: MontaVista Software, Inc. */ - .phys_io = IXP2000_UART_PHYS_BASE, - .io_pg_offst = ((IXP2000_UART_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .map_io = ixdp2x01_map_io, .init_irq = ixdp2x01_init_irq, @@ -429,8 +427,6 @@ MACHINE_END #ifdef CONFIG_ARCH_IXDP2801 MACHINE_START(IXDP2801, "Intel IXDP2801 Development Platform") /* Maintainer: MontaVista Software, Inc. */ - .phys_io = IXP2000_UART_PHYS_BASE, - .io_pg_offst = ((IXP2000_UART_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .map_io = ixdp2x01_map_io, .init_irq = ixdp2x01_init_irq, @@ -444,8 +440,6 @@ MACHINE_END */ MACHINE_START(IXDP28X5, "Intel IXDP2805/2855 Development Platform") /* Maintainer: MontaVista Software, Inc. */ - .phys_io = IXP2000_UART_PHYS_BASE, - .io_pg_offst = ((IXP2000_UART_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .map_io = ixdp2x01_map_io, .init_irq = ixdp2x01_init_irq, diff --git a/arch/arm/mach-ixp23xx/espresso.c b/arch/arm/mach-ixp23xx/espresso.c index 1c06bfc5a7efc5..e25e5fe183ba97 100644 --- a/arch/arm/mach-ixp23xx/espresso.c +++ b/arch/arm/mach-ixp23xx/espresso.c @@ -85,8 +85,6 @@ static void __init espresso_init(void) MACHINE_START(ESPRESSO, "IP Fabrics Double Espresso") /* Maintainer: Lennert Buytenhek */ - .phys_io = IXP23XX_PERIPHERAL_PHYS, - .io_pg_offst = ((IXP23XX_PERIPHERAL_VIRT >> 18)) & 0xfffc, .map_io = ixp23xx_map_io, .init_irq = ixp23xx_init_irq, .timer = &ixp23xx_timer, diff --git a/arch/arm/mach-ixp23xx/include/mach/debug-macro.S b/arch/arm/mach-ixp23xx/include/mach/debug-macro.S index a82e375465e283..f7c6eef7fa220d 100644 --- a/arch/arm/mach-ixp23xx/include/mach/debug-macro.S +++ b/arch/arm/mach-ixp23xx/include/mach/debug-macro.S @@ -12,13 +12,12 @@ */ #include - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ mmu enabled? - ldreq \rx, =IXP23XX_PERIPHERAL_PHYS @ physical - ldrne \rx, =IXP23XX_PERIPHERAL_VIRT @ virtual + .macro addruart, rp, rv + ldr \rp, =IXP23XX_PERIPHERAL_PHYS @ physical + ldr \rv, =IXP23XX_PERIPHERAL_VIRT @ virtual #ifdef __ARMEB__ - orr \rx, \rx, #0x00000003 + orr \rp, \rp, #0x00000003 + orr \rv, \rv, #0x00000003 #endif .endm diff --git a/arch/arm/mach-ixp23xx/ixdp2351.c b/arch/arm/mach-ixp23xx/ixdp2351.c index f1b124a709abd2..664e39c2a903e8 100644 --- a/arch/arm/mach-ixp23xx/ixdp2351.c +++ b/arch/arm/mach-ixp23xx/ixdp2351.c @@ -328,8 +328,6 @@ static void __init ixdp2351_init(void) MACHINE_START(IXDP2351, "Intel IXDP2351 Development Platform") /* Maintainer: MontaVista Software, Inc. */ - .phys_io = IXP23XX_PERIPHERAL_PHYS, - .io_pg_offst = ((IXP23XX_PERIPHERAL_VIRT >> 18)) & 0xfffc, .map_io = ixdp2351_map_io, .init_irq = ixdp2351_init_irq, .timer = &ixp23xx_timer, diff --git a/arch/arm/mach-ixp23xx/roadrunner.c b/arch/arm/mach-ixp23xx/roadrunner.c index 6d38d769761c1b..76c61ba7321877 100644 --- a/arch/arm/mach-ixp23xx/roadrunner.c +++ b/arch/arm/mach-ixp23xx/roadrunner.c @@ -171,8 +171,6 @@ static void __init roadrunner_init(void) MACHINE_START(ROADRUNNER, "ADI Engineering RoadRunner Development Platform") /* Maintainer: Deepak Saxena */ - .phys_io = IXP23XX_PERIPHERAL_PHYS, - .io_pg_offst = ((IXP23XX_PERIPHERAL_VIRT >> 18)) & 0xfffc, .map_io = ixp23xx_map_io, .init_irq = ixp23xx_init_irq, .timer = &ixp23xx_timer, diff --git a/arch/arm/mach-ixp4xx/avila-setup.c b/arch/arm/mach-ixp4xx/avila-setup.c index d8bc86d76f1d22..73745ff102d5da 100644 --- a/arch/arm/mach-ixp4xx/avila-setup.c +++ b/arch/arm/mach-ixp4xx/avila-setup.c @@ -164,8 +164,6 @@ static void __init avila_init(void) MACHINE_START(AVILA, "Gateworks Avila Network Platform") /* Maintainer: Deepak Saxena */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, .timer = &ixp4xx_timer, @@ -181,8 +179,6 @@ MACHINE_END #ifdef CONFIG_MACH_LOFT MACHINE_START(LOFT, "Giant Shoulder Inc Loft board") /* Maintainer: Tom Billman */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, .timer = &ixp4xx_timer, diff --git a/arch/arm/mach-ixp4xx/coyote-setup.c b/arch/arm/mach-ixp4xx/coyote-setup.c index 31a47f6a8939d8..355e3de3873371 100644 --- a/arch/arm/mach-ixp4xx/coyote-setup.c +++ b/arch/arm/mach-ixp4xx/coyote-setup.c @@ -109,8 +109,6 @@ static void __init coyote_init(void) #ifdef CONFIG_ARCH_ADI_COYOTE MACHINE_START(ADI_COYOTE, "ADI Engineering Coyote") /* Maintainer: MontaVista Software, Inc. */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, .timer = &ixp4xx_timer, @@ -126,8 +124,6 @@ MACHINE_END #ifdef CONFIG_MACH_IXDPG425 MACHINE_START(IXDPG425, "Intel IXDPG425") /* Maintainer: MontaVista Software, Inc. */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, .timer = &ixp4xx_timer, diff --git a/arch/arm/mach-ixp4xx/dsmg600-setup.c b/arch/arm/mach-ixp4xx/dsmg600-setup.c index 7c1fa54a6145a9..d398229cfaa5d4 100644 --- a/arch/arm/mach-ixp4xx/dsmg600-setup.c +++ b/arch/arm/mach-ixp4xx/dsmg600-setup.c @@ -279,8 +279,6 @@ static void __init dsmg600_init(void) MACHINE_START(DSMG600, "D-Link DSM-G600 RevA") /* Maintainer: www.nslu2-linux.org */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC, .boot_params = 0x00000100, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, diff --git a/arch/arm/mach-ixp4xx/fsg-setup.c b/arch/arm/mach-ixp4xx/fsg-setup.c index e7f4befba4224b..727ee39ce11c1e 100644 --- a/arch/arm/mach-ixp4xx/fsg-setup.c +++ b/arch/arm/mach-ixp4xx/fsg-setup.c @@ -270,8 +270,6 @@ static void __init fsg_init(void) MACHINE_START(FSG, "Freecom FSG-3") /* Maintainer: www.nslu2-linux.org */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, .timer = &ixp4xx_timer, diff --git a/arch/arm/mach-ixp4xx/gateway7001-setup.c b/arch/arm/mach-ixp4xx/gateway7001-setup.c index 2583b2a13174ef..9dc0b4eaa65adb 100644 --- a/arch/arm/mach-ixp4xx/gateway7001-setup.c +++ b/arch/arm/mach-ixp4xx/gateway7001-setup.c @@ -96,8 +96,6 @@ static void __init gateway7001_init(void) #ifdef CONFIG_MACH_GATEWAY7001 MACHINE_START(GATEWAY7001, "Gateway 7001 AP") /* Maintainer: Imre Kaloz */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, .timer = &ixp4xx_timer, diff --git a/arch/arm/mach-ixp4xx/goramo_mlr.c b/arch/arm/mach-ixp4xx/goramo_mlr.c index 1c28048209c14c..d0e4861ac03d5b 100644 --- a/arch/arm/mach-ixp4xx/goramo_mlr.c +++ b/arch/arm/mach-ixp4xx/goramo_mlr.c @@ -496,8 +496,6 @@ subsys_initcall(gmlr_pci_init); MACHINE_START(GORAMO_MLR, "MultiLink") /* Maintainer: Krzysztof Halasa */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, .timer = &ixp4xx_timer, diff --git a/arch/arm/mach-ixp4xx/gtwx5715-setup.c b/arch/arm/mach-ixp4xx/gtwx5715-setup.c index c67586b79400c8..77abead3622774 100644 --- a/arch/arm/mach-ixp4xx/gtwx5715-setup.c +++ b/arch/arm/mach-ixp4xx/gtwx5715-setup.c @@ -164,8 +164,6 @@ static void __init gtwx5715_init(void) MACHINE_START(GTWX5715, "Gemtek GTWX5715 (Linksys WRV54G)") /* Maintainer: George Joseph */ - .phys_io = IXP4XX_UART2_BASE_PHYS, - .io_pg_offst = ((IXP4XX_UART2_BASE_VIRT) >> 18) & 0xfffc, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, .timer = &ixp4xx_timer, diff --git a/arch/arm/mach-ixp4xx/include/mach/debug-macro.S b/arch/arm/mach-ixp4xx/include/mach/debug-macro.S index 3fc66d6d00a01f..b974a49c0aff45 100644 --- a/arch/arm/mach-ixp4xx/include/mach/debug-macro.S +++ b/arch/arm/mach-ixp4xx/include/mach/debug-macro.S @@ -10,16 +10,16 @@ * published by the Free Software Foundation. */ - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - moveq \rx, #0xc8000000 - movne \rx, #0xff000000 - orrne \rx, \rx, #0x00b00000 + .macro addruart, rp, rv #ifdef __ARMEB__ - add \rx,\rx,#3 @ Uart regs are at off set of 3 if - @ byte writes used - Big Endian. + mov \rp, #3 @ Uart regs are at off set of 3 if + @ byte writes used - Big Endian. +#else + mov \rp, #0 #endif + orr \rv, \rp, #0xff000000 @ virtual + orr \rv, \rv, #0x00b00000 + orr \rp, \rp, #0xc8000000 @ physical .endm #define UART_SHIFT 2 diff --git a/arch/arm/mach-ixp4xx/ixdp425-setup.c b/arch/arm/mach-ixp4xx/ixdp425-setup.c index ea9ee4ed0a3e06..14078338678551 100644 --- a/arch/arm/mach-ixp4xx/ixdp425-setup.c +++ b/arch/arm/mach-ixp4xx/ixdp425-setup.c @@ -257,8 +257,6 @@ static void __init ixdp425_init(void) #ifdef CONFIG_ARCH_IXDP425 MACHINE_START(IXDP425, "Intel IXDP425 Development Platform") /* Maintainer: MontaVista Software, Inc. */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, .timer = &ixp4xx_timer, @@ -270,8 +268,6 @@ MACHINE_END #ifdef CONFIG_MACH_IXDP465 MACHINE_START(IXDP465, "Intel IXDP465 Development Platform") /* Maintainer: MontaVista Software, Inc. */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, .timer = &ixp4xx_timer, @@ -283,8 +279,6 @@ MACHINE_END #ifdef CONFIG_ARCH_PRPMC1100 MACHINE_START(IXCDP1100, "Intel IXCDP1100 Development Platform") /* Maintainer: MontaVista Software, Inc. */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, .timer = &ixp4xx_timer, @@ -296,8 +290,6 @@ MACHINE_END #ifdef CONFIG_MACH_KIXRP435 MACHINE_START(KIXRP435, "Intel KIXRP435 Reference Platform") /* Maintainer: MontaVista Software, Inc. */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, .timer = &ixp4xx_timer, diff --git a/arch/arm/mach-ixp4xx/nas100d-setup.c b/arch/arm/mach-ixp4xx/nas100d-setup.c index e3ee880aa1e687..f18fee748878e9 100644 --- a/arch/arm/mach-ixp4xx/nas100d-setup.c +++ b/arch/arm/mach-ixp4xx/nas100d-setup.c @@ -314,8 +314,6 @@ static void __init nas100d_init(void) MACHINE_START(NAS100D, "Iomega NAS 100d") /* Maintainer: www.nslu2-linux.org */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC, .boot_params = 0x00000100, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, diff --git a/arch/arm/mach-ixp4xx/nslu2-setup.c b/arch/arm/mach-ixp4xx/nslu2-setup.c index c14e0034be4b42..f79b62eb7614ec 100644 --- a/arch/arm/mach-ixp4xx/nslu2-setup.c +++ b/arch/arm/mach-ixp4xx/nslu2-setup.c @@ -300,8 +300,6 @@ static void __init nslu2_init(void) MACHINE_START(NSLU2, "Linksys NSLU2") /* Maintainer: www.nslu2-linux.org */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC, .boot_params = 0x00000100, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, diff --git a/arch/arm/mach-ixp4xx/vulcan-setup.c b/arch/arm/mach-ixp4xx/vulcan-setup.c index 465cc5cce687df..4e72cfdd3c461d 100644 --- a/arch/arm/mach-ixp4xx/vulcan-setup.c +++ b/arch/arm/mach-ixp4xx/vulcan-setup.c @@ -236,8 +236,6 @@ static void __init vulcan_init(void) MACHINE_START(ARCOM_VULCAN, "Arcom/Eurotech Vulcan") /* Maintainer: Marc Zyngier */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, .timer = &ixp4xx_timer, diff --git a/arch/arm/mach-ixp4xx/wg302v2-setup.c b/arch/arm/mach-ixp4xx/wg302v2-setup.c index 4dd74863daa9cb..5d148c7bc4fbd1 100644 --- a/arch/arm/mach-ixp4xx/wg302v2-setup.c +++ b/arch/arm/mach-ixp4xx/wg302v2-setup.c @@ -97,8 +97,6 @@ static void __init wg302v2_init(void) #ifdef CONFIG_MACH_WG302V2 MACHINE_START(WG302V2, "Netgear WG302 v2 / WAG302 v2") /* Maintainer: Imre Kaloz */ - .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, - .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, .map_io = ixp4xx_map_io, .init_irq = ixp4xx_init_irq, .timer = &ixp4xx_timer, diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig index cc25501b57fa8e..34106335c728f3 100644 --- a/arch/arm/mach-kirkwood/Kconfig +++ b/arch/arm/mach-kirkwood/Kconfig @@ -58,6 +58,12 @@ config MACH_TS41X QNAP TS-410, TS-410U, TS-419P and TS-419U Turbo NAS devices. +config MACH_DOCKSTAR + bool "Seagate FreeAgent DockStar" + help + Say 'Y' here if you want your kernel to support the + Seagate FreeAgent DockStar. + config MACH_OPENRD bool @@ -100,6 +106,12 @@ config MACH_NETSPACE_MAX_V2 Say 'Y' here if you want your kernel to support the LaCie Network Space Max v2 NAS. +config MACH_D2NET_V2 + bool "LaCie d2 Network v2 NAS Board" + help + Say 'Y' here if you want your kernel to support the + LaCie d2 Network v2 NAS. + config MACH_NET2BIG_V2 bool "LaCie 2Big Network v2 NAS Board" help diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile index 295d7baa6ae111..5dcaa81a2ec39f 100644 --- a/arch/arm/mach-kirkwood/Makefile +++ b/arch/arm/mach-kirkwood/Makefile @@ -7,14 +7,16 @@ obj-$(CONFIG_MACH_MV88F6281GTW_GE) += mv88f6281gtw_ge-setup.o obj-$(CONFIG_MACH_SHEEVAPLUG) += sheevaplug-setup.o obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG) += sheevaplug-setup.o obj-$(CONFIG_MACH_GURUPLUG) += guruplug-setup.o +obj-$(CONFIG_MACH_DOCKSTAR) += dockstar-setup.o obj-$(CONFIG_MACH_TS219) += ts219-setup.o tsx1x-common.o obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o obj-$(CONFIG_MACH_OPENRD) += openrd-setup.o -obj-$(CONFIG_MACH_NETSPACE_V2) += netspace_v2-setup.o -obj-$(CONFIG_MACH_INETSPACE_V2) += netspace_v2-setup.o -obj-$(CONFIG_MACH_NETSPACE_MAX_V2) += netspace_v2-setup.o -obj-$(CONFIG_MACH_NET2BIG_V2) += netxbig_v2-setup.o -obj-$(CONFIG_MACH_NET5BIG_V2) += netxbig_v2-setup.o +obj-$(CONFIG_MACH_NETSPACE_V2) += netspace_v2-setup.o lacie_v2-common.o +obj-$(CONFIG_MACH_INETSPACE_V2) += netspace_v2-setup.o lacie_v2-common.o +obj-$(CONFIG_MACH_NETSPACE_MAX_V2) += netspace_v2-setup.o lacie_v2-common.o +obj-$(CONFIG_MACH_D2NET_V2) += d2net_v2-setup.o lacie_v2-common.o +obj-$(CONFIG_MACH_NET2BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o +obj-$(CONFIG_MACH_NET5BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o obj-$(CONFIG_MACH_T5325) += t5325-setup.o obj-$(CONFIG_CPU_IDLE) += cpuidle.o diff --git a/arch/arm/mach-kirkwood/d2net_v2-setup.c b/arch/arm/mach-kirkwood/d2net_v2-setup.c new file mode 100644 index 00000000000000..4aa86e4a152c22 --- /dev/null +++ b/arch/arm/mach-kirkwood/d2net_v2-setup.c @@ -0,0 +1,229 @@ +/* + * arch/arm/mach-kirkwood/d2net_v2-setup.c + * + * LaCie d2 Network Space v2 Board Setup + * + * Copyright (C) 2010 Simon Guinot + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "common.h" +#include "mpp.h" +#include "lacie_v2-common.h" + +/***************************************************************************** + * Ethernet + ****************************************************************************/ + +static struct mv643xx_eth_platform_data d2net_v2_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(8), +}; + +/***************************************************************************** + * SATA + ****************************************************************************/ + +static struct mv_sata_platform_data d2net_v2_sata_data = { + .n_ports = 2, +}; + +/***************************************************************************** + * GPIO keys + ****************************************************************************/ + +#define D2NET_V2_GPIO_PUSH_BUTTON 34 +#define D2NET_V2_GPIO_POWER_SWITCH_ON 13 +#define D2NET_V2_GPIO_POWER_SWITCH_OFF 15 + +#define D2NET_V2_SWITCH_POWER_ON 0x1 +#define D2NET_V2_SWITCH_POWER_OFF 0x2 + +static struct gpio_keys_button d2net_v2_buttons[] = { + [0] = { + .type = EV_SW, + .code = D2NET_V2_SWITCH_POWER_ON, + .gpio = D2NET_V2_GPIO_POWER_SWITCH_ON, + .desc = "Back power switch (on|auto)", + .active_low = 0, + }, + [1] = { + .type = EV_SW, + .code = D2NET_V2_SWITCH_POWER_OFF, + .gpio = D2NET_V2_GPIO_POWER_SWITCH_OFF, + .desc = "Back power switch (auto|off)", + .active_low = 0, + }, + [2] = { + .code = KEY_POWER, + .gpio = D2NET_V2_GPIO_PUSH_BUTTON, + .desc = "Front Push Button", + .active_low = 1, + }, +}; + +static struct gpio_keys_platform_data d2net_v2_button_data = { + .buttons = d2net_v2_buttons, + .nbuttons = ARRAY_SIZE(d2net_v2_buttons), +}; + +static struct platform_device d2net_v2_gpio_buttons = { + .name = "gpio-keys", + .id = -1, + .dev = { + .platform_data = &d2net_v2_button_data, + }, +}; + +/***************************************************************************** + * GPIO LEDs + ****************************************************************************/ + +#define D2NET_V2_GPIO_RED_LED 12 + +static struct gpio_led d2net_v2_gpio_led_pins[] = { + { + .name = "d2net_v2:red:fail", + .gpio = D2NET_V2_GPIO_RED_LED, + }, +}; + +static struct gpio_led_platform_data d2net_v2_gpio_leds_data = { + .num_leds = ARRAY_SIZE(d2net_v2_gpio_led_pins), + .leds = d2net_v2_gpio_led_pins, +}; + +static struct platform_device d2net_v2_gpio_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &d2net_v2_gpio_leds_data, + }, +}; + +/***************************************************************************** + * Dual-GPIO CPLD LEDs + ****************************************************************************/ + +#define D2NET_V2_GPIO_BLUE_LED_SLOW 29 +#define D2NET_V2_GPIO_BLUE_LED_CMD 30 + +static struct ns2_led d2net_v2_led_pins[] = { + { + .name = "d2net_v2:blue:sata", + .cmd = D2NET_V2_GPIO_BLUE_LED_CMD, + .slow = D2NET_V2_GPIO_BLUE_LED_SLOW, + }, +}; + +static struct ns2_led_platform_data d2net_v2_leds_data = { + .num_leds = ARRAY_SIZE(d2net_v2_led_pins), + .leds = d2net_v2_led_pins, +}; + +static struct platform_device d2net_v2_leds = { + .name = "leds-ns2", + .id = -1, + .dev = { + .platform_data = &d2net_v2_leds_data, + }, +}; + +/***************************************************************************** + * General Setup + ****************************************************************************/ + +static unsigned int d2net_v2_mpp_config[] __initdata = { + MPP0_SPI_SCn, + MPP1_SPI_MOSI, + MPP2_SPI_SCK, + MPP3_SPI_MISO, + MPP6_SYSRST_OUTn, + MPP7_GPO, /* Request power-off */ + MPP8_TW0_SDA, + MPP9_TW0_SCK, + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_GPO, /* Red led */ + MPP13_GPIO, /* Rear power switch (on|auto) */ + MPP14_GPIO, /* USB fuse */ + MPP15_GPIO, /* Rear power switch (auto|off) */ + MPP16_GPIO, /* SATA 0 power */ + MPP21_SATA0_ACTn, + MPP24_GPIO, /* USB mode select */ + MPP26_GPIO, /* USB device vbus */ + MPP28_GPIO, /* USB enable host vbus */ + MPP29_GPIO, /* Blue led (slow register) */ + MPP30_GPIO, /* Blue led (command register) */ + MPP34_GPIO, /* Power button (1 = Released, 0 = Pushed) */ + MPP35_GPIO, /* Inhibit power-off */ + 0 +}; + +#define D2NET_V2_GPIO_POWER_OFF 7 + +static void d2net_v2_power_off(void) +{ + gpio_set_value(D2NET_V2_GPIO_POWER_OFF, 1); +} + +static void __init d2net_v2_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + kirkwood_mpp_conf(d2net_v2_mpp_config); + + lacie_v2_hdd_power_init(1); + + kirkwood_ehci_init(); + kirkwood_ge00_init(&d2net_v2_ge00_data); + kirkwood_sata_init(&d2net_v2_sata_data); + kirkwood_uart0_init(); + lacie_v2_register_flash(); + lacie_v2_register_i2c_devices(); + + platform_device_register(&d2net_v2_leds); + platform_device_register(&d2net_v2_gpio_leds); + platform_device_register(&d2net_v2_gpio_buttons); + + if (gpio_request(D2NET_V2_GPIO_POWER_OFF, "power-off") == 0 && + gpio_direction_output(D2NET_V2_GPIO_POWER_OFF, 0) == 0) + pm_power_off = d2net_v2_power_off; + else + pr_err("d2net_v2: failed to configure power-off GPIO\n"); +} + +MACHINE_START(D2NET_V2, "LaCie d2 Network v2") + .boot_params = 0x00000100, + .init_machine = d2net_v2_init, + .map_io = kirkwood_map_io, + .init_irq = kirkwood_init_irq, + .timer = &lacie_v2_timer, +MACHINE_END diff --git a/arch/arm/mach-kirkwood/db88f6281-bp-setup.c b/arch/arm/mach-kirkwood/db88f6281-bp-setup.c index 16f6691e7c685c..9ea71182d31ac5 100644 --- a/arch/arm/mach-kirkwood/db88f6281-bp-setup.c +++ b/arch/arm/mach-kirkwood/db88f6281-bp-setup.c @@ -97,8 +97,6 @@ subsys_initcall(db88f6281_pci_init); MACHINE_START(DB88F6281_BP, "Marvell DB-88F6281-BP Development Board") /* Maintainer: Saeed Bishara */ - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = db88f6281_init, .map_io = kirkwood_map_io, diff --git a/arch/arm/mach-kirkwood/dockstar-setup.c b/arch/arm/mach-kirkwood/dockstar-setup.c new file mode 100644 index 00000000000000..433ea368c060fb --- /dev/null +++ b/arch/arm/mach-kirkwood/dockstar-setup.c @@ -0,0 +1,110 @@ +/* + * arch/arm/mach-kirkwood/dockstar-setup.c + * + * Seagate FreeAgent DockStar Setup + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "common.h" +#include "mpp.h" + +static struct mtd_partition dockstar_nand_parts[] = { + { + .name = "u-boot", + .offset = 0, + .size = SZ_1M + }, { + .name = "uImage", + .offset = MTDPART_OFS_NXTBLK, + .size = SZ_4M + }, { + .name = "root", + .offset = MTDPART_OFS_NXTBLK, + .size = MTDPART_SIZ_FULL + }, +}; + +static struct mv643xx_eth_platform_data dockstar_ge00_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(0), +}; + +static struct gpio_led dockstar_led_pins[] = { + { + .name = "dockstar:green:health", + .default_trigger = "default-on", + .gpio = 46, + .active_low = 1, + }, + { + .name = "dockstar:orange:misc", + .default_trigger = "none", + .gpio = 47, + .active_low = 1, + }, +}; + +static struct gpio_led_platform_data dockstar_led_data = { + .leds = dockstar_led_pins, + .num_leds = ARRAY_SIZE(dockstar_led_pins), +}; + +static struct platform_device dockstar_leds = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &dockstar_led_data, + } +}; + +static unsigned int dockstar_mpp_config[] __initdata = { + MPP29_GPIO, /* USB Power Enable */ + MPP46_GPIO, /* LED green */ + MPP47_GPIO, /* LED orange */ + 0 +}; + +static void __init dockstar_init(void) +{ + /* + * Basic setup. Needs to be called early. + */ + kirkwood_init(); + + /* setup gpio pin select */ + kirkwood_mpp_conf(dockstar_mpp_config); + + kirkwood_uart0_init(); + kirkwood_nand_init(ARRAY_AND_SIZE(dockstar_nand_parts), 25); + + if (gpio_request(29, "USB Power Enable") != 0 || + gpio_direction_output(29, 1) != 0) + printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n"); + kirkwood_ehci_init(); + + kirkwood_ge00_init(&dockstar_ge00_data); + + platform_device_register(&dockstar_leds); +} + +MACHINE_START(DOCKSTAR, "Seagate FreeAgent DockStar") + .boot_params = 0x00000100, + .init_machine = dockstar_init, + .map_io = kirkwood_map_io, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, +MACHINE_END diff --git a/arch/arm/mach-kirkwood/guruplug-setup.c b/arch/arm/mach-kirkwood/guruplug-setup.c index 54d07c89d4ffe2..8f47dc0a2feff7 100644 --- a/arch/arm/mach-kirkwood/guruplug-setup.c +++ b/arch/arm/mach-kirkwood/guruplug-setup.c @@ -121,8 +121,6 @@ static void __init guruplug_init(void) MACHINE_START(GURUPLUG, "Marvell GuruPlug Reference Board") /* Maintainer: Siddarth Gore */ - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = guruplug_init, .map_io = kirkwood_map_io, diff --git a/arch/arm/mach-kirkwood/include/mach/debug-macro.S b/arch/arm/mach-kirkwood/include/mach/debug-macro.S index d0606774dea7de..db06ae437d08c6 100644 --- a/arch/arm/mach-kirkwood/include/mach/debug-macro.S +++ b/arch/arm/mach-kirkwood/include/mach/debug-macro.S @@ -8,12 +8,11 @@ #include - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - ldreq \rx, =KIRKWOOD_REGS_PHYS_BASE - ldrne \rx, =KIRKWOOD_REGS_VIRT_BASE - orr \rx, \rx, #0x00012000 + .macro addruart, rp, rv + ldr \rp, =KIRKWOOD_REGS_PHYS_BASE + ldr \rv, =KIRKWOOD_REGS_VIRT_BASE + orr \rp, \rp, #0x00012000 + orr \rv, \rv, #0x00012000 .endm #define UART_SHIFT 2 diff --git a/arch/arm/mach-kirkwood/include/mach/leds-netxbig.h b/arch/arm/mach-kirkwood/include/mach/leds-netxbig.h new file mode 100644 index 00000000000000..24b536ebdf13de --- /dev/null +++ b/arch/arm/mach-kirkwood/include/mach/leds-netxbig.h @@ -0,0 +1,55 @@ +/* + * arch/arm/mach-kirkwood/include/mach/leds-netxbig.h + * + * Platform data structure for netxbig LED driver + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __MACH_LEDS_NETXBIG_H +#define __MACH_LEDS_NETXBIG_H + +struct netxbig_gpio_ext { + unsigned *addr; + int num_addr; + unsigned *data; + int num_data; + unsigned enable; +}; + +enum netxbig_led_mode { + NETXBIG_LED_OFF, + NETXBIG_LED_ON, + NETXBIG_LED_SATA, + NETXBIG_LED_TIMER1, + NETXBIG_LED_TIMER2, + NETXBIG_LED_MODE_NUM, +}; + +#define NETXBIG_LED_INVALID_MODE NETXBIG_LED_MODE_NUM + +struct netxbig_led_timer { + unsigned long delay_on; + unsigned long delay_off; + enum netxbig_led_mode mode; +}; + +struct netxbig_led { + const char *name; + const char *default_trigger; + int mode_addr; + int *mode_val; + int bright_addr; +}; + +struct netxbig_led_platform_data { + struct netxbig_gpio_ext *gpio_ext; + struct netxbig_led_timer *timer; + int num_timer; + struct netxbig_led *leds; + int num_leds; +}; + +#endif /* __MACH_LEDS_NETXBIG_H */ diff --git a/arch/arm/mach-kirkwood/lacie_v2-common.c b/arch/arm/mach-kirkwood/lacie_v2-common.c new file mode 100644 index 00000000000000..d3ea1b6c8a02ff --- /dev/null +++ b/arch/arm/mach-kirkwood/lacie_v2-common.c @@ -0,0 +1,127 @@ +/* + * arch/arm/mach-kirkwood/lacie_v2-common.c + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "common.h" + +/***************************************************************************** + * 512KB SPI Flash on Boot Device (MACRONIX MX25L4005) + ****************************************************************************/ + +static struct mtd_partition lacie_v2_flash_parts[] = { + { + .name = "u-boot", + .size = MTDPART_SIZ_FULL, + .offset = 0, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, +}; + +static const struct flash_platform_data lacie_v2_flash = { + .type = "mx25l4005a", + .name = "spi_flash", + .parts = lacie_v2_flash_parts, + .nr_parts = ARRAY_SIZE(lacie_v2_flash_parts), +}; + +static struct spi_board_info __initdata lacie_v2_spi_slave_info[] = { + { + .modalias = "m25p80", + .platform_data = &lacie_v2_flash, + .irq = -1, + .max_speed_hz = 20000000, + .bus_num = 0, + .chip_select = 0, + }, +}; + +void __init lacie_v2_register_flash(void) +{ + spi_register_board_info(lacie_v2_spi_slave_info, + ARRAY_SIZE(lacie_v2_spi_slave_info)); + kirkwood_spi_init(); +} + +/***************************************************************************** + * I2C devices + ****************************************************************************/ + +static struct at24_platform_data at24c04 = { + .byte_len = SZ_4K / 8, + .page_size = 16, +}; + +/* + * i2c addr | chip | description + * 0x50 | HT24LC04 | eeprom (512B) + */ + +static struct i2c_board_info __initdata lacie_v2_i2c_info[] = { + { + I2C_BOARD_INFO("24c04", 0x50), + .platform_data = &at24c04, + } +}; + +void __init lacie_v2_register_i2c_devices(void) +{ + kirkwood_i2c_init(); + i2c_register_board_info(0, lacie_v2_i2c_info, + ARRAY_SIZE(lacie_v2_i2c_info)); +} + +/***************************************************************************** + * Hard Disk power + ****************************************************************************/ + +static int __initdata lacie_v2_gpio_hdd_power[] = { 16, 17, 41, 42, 43 }; + +void __init lacie_v2_hdd_power_init(int hdd_num) +{ + int i; + int err; + + /* Power up all hard disks. */ + for (i = 0; i < hdd_num; i++) { + err = gpio_request(lacie_v2_gpio_hdd_power[i], NULL); + if (err == 0) { + err = gpio_direction_output( + lacie_v2_gpio_hdd_power[i], 1); + /* Free the HDD power GPIOs. This allow user-space to + * configure them via the gpiolib sysfs interface. */ + gpio_free(lacie_v2_gpio_hdd_power[i]); + } + if (err) + pr_err("Failed to power up HDD%d\n", i + 1); + } +} + +/***************************************************************************** + * Timer + ****************************************************************************/ + +static void lacie_v2_timer_init(void) +{ + kirkwood_tclk = 166666667; + orion_time_init(IRQ_KIRKWOOD_BRIDGE, kirkwood_tclk); +} + +struct sys_timer lacie_v2_timer = { + .init = lacie_v2_timer_init, +}; diff --git a/arch/arm/mach-kirkwood/lacie_v2-common.h b/arch/arm/mach-kirkwood/lacie_v2-common.h new file mode 100644 index 00000000000000..af521315b87bd6 --- /dev/null +++ b/arch/arm/mach-kirkwood/lacie_v2-common.h @@ -0,0 +1,18 @@ +/* + * arch/arm/mach-kirkwood/lacie_v2-common.h + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ARCH_KIRKWOOD_LACIE_V2_COMMON_H +#define __ARCH_KIRKWOOD_LACIE_V2_COMMON_H + +void lacie_v2_register_flash(void); +void lacie_v2_register_i2c_devices(void); +void lacie_v2_hdd_power_init(int hdd_num); + +extern struct sys_timer lacie_v2_timer; + +#endif diff --git a/arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c b/arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c index c6b92b42eb4e5a..1e5266f57e2a2d 100644 --- a/arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c +++ b/arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c @@ -163,8 +163,6 @@ subsys_initcall(mv88f6281gtw_ge_pci_init); MACHINE_START(MV88F6281GTW_GE, "Marvell 88F6281 GTW GE Board") /* Maintainer: Lennert Buytenhek */ - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = mv88f6281gtw_ge_init, .map_io = kirkwood_map_io, diff --git a/arch/arm/mach-kirkwood/netspace_v2-setup.c b/arch/arm/mach-kirkwood/netspace_v2-setup.c index d26bf324738bde..5e286441b8f45f 100644 --- a/arch/arm/mach-kirkwood/netspace_v2-setup.c +++ b/arch/arm/mach-kirkwood/netspace_v2-setup.c @@ -24,56 +24,19 @@ #include #include #include -#include -#include -#include #include #include -#include -#include #include #include #include #include #include #include -#include #include #include -#include #include "common.h" #include "mpp.h" - -/***************************************************************************** - * 512KB SPI Flash on Boot Device (MACRONIX MX25L4005) - ****************************************************************************/ - -static struct mtd_partition netspace_v2_flash_parts[] = { - { - .name = "u-boot", - .size = MTDPART_SIZ_FULL, - .offset = 0, - .mask_flags = MTD_WRITEABLE, /* force read-only */ - }, -}; - -static const struct flash_platform_data netspace_v2_flash = { - .type = "mx25l4005a", - .name = "spi_flash", - .parts = netspace_v2_flash_parts, - .nr_parts = ARRAY_SIZE(netspace_v2_flash_parts), -}; - -static struct spi_board_info __initdata netspace_v2_spi_slave_info[] = { - { - .modalias = "m25p80", - .platform_data = &netspace_v2_flash, - .irq = -1, - .max_speed_hz = 20000000, - .bus_num = 0, - .chip_select = 0, - }, -}; +#include "lacie_v2-common.h" /***************************************************************************** * Ethernet @@ -83,27 +46,6 @@ static struct mv643xx_eth_platform_data netspace_v2_ge00_data = { .phy_addr = MV643XX_ETH_PHY_ADDR(8), }; -/***************************************************************************** - * I2C devices - ****************************************************************************/ - -static struct at24_platform_data at24c04 = { - .byte_len = SZ_4K / 8, - .page_size = 16, -}; - -/* - * i2c addr | chip | description - * 0x50 | HT24LC04 | eeprom (512B) - */ - -static struct i2c_board_info __initdata netspace_v2_i2c_info[] = { - { - I2C_BOARD_INFO("24c04", 0x50), - .platform_data = &at24c04, - } -}; - /***************************************************************************** * SATA ****************************************************************************/ @@ -112,35 +54,6 @@ static struct mv_sata_platform_data netspace_v2_sata_data = { .n_ports = 2, }; -#define NETSPACE_V2_GPIO_SATA0_POWER 16 -#define NETSPACE_V2_GPIO_SATA1_POWER 17 - -static void __init netspace_v2_sata_power_init(void) -{ - int err; - - err = gpio_request(NETSPACE_V2_GPIO_SATA0_POWER, "SATA0 power"); - if (err == 0) { - err = gpio_direction_output(NETSPACE_V2_GPIO_SATA0_POWER, 1); - if (err) - gpio_free(NETSPACE_V2_GPIO_SATA0_POWER); - } - if (err) - pr_err("netspace_v2: failed to setup SATA0 power\n"); - - if (machine_is_netspace_max_v2()) { - err = gpio_request(NETSPACE_V2_GPIO_SATA1_POWER, "SATA1 power"); - if (err == 0) { - err = gpio_direction_output( - NETSPACE_V2_GPIO_SATA1_POWER, 1); - if (err) - gpio_free(NETSPACE_V2_GPIO_SATA1_POWER); - } - if (err) - pr_err("netspace_v2: failed to setup SATA1 power\n"); - } -} - /***************************************************************************** * GPIO keys ****************************************************************************/ @@ -223,20 +136,6 @@ static struct platform_device netspace_v2_leds = { }, }; -/***************************************************************************** - * Timer - ****************************************************************************/ - -static void netspace_v2_timer_init(void) -{ - kirkwood_tclk = 166666667; - orion_time_init(IRQ_KIRKWOOD_BRIDGE, kirkwood_tclk); -} - -struct sys_timer netspace_v2_timer = { - .init = netspace_v2_timer_init, -}; - /***************************************************************************** * General Setup ****************************************************************************/ @@ -291,18 +190,17 @@ static void __init netspace_v2_init(void) kirkwood_init(); kirkwood_mpp_conf(netspace_v2_mpp_config); - netspace_v2_sata_power_init(); + if (machine_is_netspace_max_v2()) + lacie_v2_hdd_power_init(2); + else + lacie_v2_hdd_power_init(1); kirkwood_ehci_init(); kirkwood_ge00_init(&netspace_v2_ge00_data); kirkwood_sata_init(&netspace_v2_sata_data); kirkwood_uart0_init(); - spi_register_board_info(netspace_v2_spi_slave_info, - ARRAY_SIZE(netspace_v2_spi_slave_info)); - kirkwood_spi_init(); - kirkwood_i2c_init(); - i2c_register_board_info(0, netspace_v2_i2c_info, - ARRAY_SIZE(netspace_v2_i2c_info)); + lacie_v2_register_flash(); + lacie_v2_register_i2c_devices(); platform_device_register(&netspace_v2_leds); platform_device_register(&netspace_v2_gpio_leds); @@ -317,36 +215,30 @@ static void __init netspace_v2_init(void) #ifdef CONFIG_MACH_NETSPACE_V2 MACHINE_START(NETSPACE_V2, "LaCie Network Space v2") - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = netspace_v2_init, .map_io = kirkwood_map_io, .init_irq = kirkwood_init_irq, - .timer = &netspace_v2_timer, + .timer = &lacie_v2_timer, MACHINE_END #endif #ifdef CONFIG_MACH_INETSPACE_V2 MACHINE_START(INETSPACE_V2, "LaCie Internet Space v2") - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = netspace_v2_init, .map_io = kirkwood_map_io, .init_irq = kirkwood_init_irq, - .timer = &netspace_v2_timer, + .timer = &lacie_v2_timer, MACHINE_END #endif #ifdef CONFIG_MACH_NETSPACE_MAX_V2 MACHINE_START(NETSPACE_MAX_V2, "LaCie Network Space Max v2") - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = netspace_v2_init, .map_io = kirkwood_map_io, .init_irq = kirkwood_init_irq, - .timer = &netspace_v2_timer, + .timer = &lacie_v2_timer, MACHINE_END #endif diff --git a/arch/arm/mach-kirkwood/netxbig_v2-setup.c b/arch/arm/mach-kirkwood/netxbig_v2-setup.c index 2bd14c5079de7c..a1b45d501aef57 100644 --- a/arch/arm/mach-kirkwood/netxbig_v2-setup.c +++ b/arch/arm/mach-kirkwood/netxbig_v2-setup.c @@ -23,55 +23,19 @@ #include #include #include -#include -#include -#include #include #include -#include -#include #include #include #include #include #include #include -#include #include -#include +#include #include "common.h" #include "mpp.h" - -/***************************************************************************** - * 512KB SPI Flash on Boot Device (MACRONIX MX25L4005) - ****************************************************************************/ - -static struct mtd_partition netxbig_v2_flash_parts[] = { - { - .name = "u-boot", - .size = MTDPART_SIZ_FULL, - .offset = 0, - .mask_flags = MTD_WRITEABLE, /* force read-only */ - }, -}; - -static const struct flash_platform_data netxbig_v2_flash = { - .type = "mx25l4005a", - .name = "spi_flash", - .parts = netxbig_v2_flash_parts, - .nr_parts = ARRAY_SIZE(netxbig_v2_flash_parts), -}; - -static struct spi_board_info __initdata netxbig_v2_spi_slave_info[] = { - { - .modalias = "m25p80", - .platform_data = &netxbig_v2_flash, - .irq = -1, - .max_speed_hz = 20000000, - .bus_num = 0, - .chip_select = 0, - }, -}; +#include "lacie_v2-common.h" /***************************************************************************** * Ethernet @@ -85,27 +49,6 @@ static struct mv643xx_eth_platform_data netxbig_v2_ge01_data = { .phy_addr = MV643XX_ETH_PHY_ADDR(0), }; -/***************************************************************************** - * I2C devices - ****************************************************************************/ - -static struct at24_platform_data at24c04 = { - .byte_len = SZ_4K / 8, - .page_size = 16, -}; - -/* - * i2c addr | chip | description - * 0x50 | HT24LC04 | eeprom (512B) - */ - -static struct i2c_board_info __initdata netxbig_v2_i2c_info[] = { - { - I2C_BOARD_INFO("24c04", 0x50), - .platform_data = &at24c04, - } -}; - /***************************************************************************** * SATA ****************************************************************************/ @@ -114,34 +57,6 @@ static struct mv_sata_platform_data netxbig_v2_sata_data = { .n_ports = 2, }; -static int __initdata netxbig_v2_gpio_hdd_power[] = { 16, 17, 41, 42, 43 }; - -static void __init netxbig_v2_sata_power_init(void) -{ - int i; - int err; - int hdd_nb; - - if (machine_is_net2big_v2()) - hdd_nb = 2; - else - hdd_nb = 5; - - /* Power up all hard disks. */ - for (i = 0; i < hdd_nb; i++) { - err = gpio_request(netxbig_v2_gpio_hdd_power[i], NULL); - if (err == 0) { - err = gpio_direction_output( - netxbig_v2_gpio_hdd_power[i], 1); - /* Free the HDD power GPIOs. This allow user-space to - * configure them via the gpiolib sysfs interface. */ - gpio_free(netxbig_v2_gpio_hdd_power[i]); - } - if (err) - pr_err("netxbig_v2: failed to power up HDD%d\n", i + 1); - } -} - /***************************************************************************** * GPIO keys ****************************************************************************/ @@ -190,7 +105,7 @@ static struct platform_device netxbig_v2_gpio_buttons = { }; /***************************************************************************** - * GPIO LEDs + * GPIO extension LEDs ****************************************************************************/ /* @@ -200,19 +115,32 @@ static struct platform_device netxbig_v2_gpio_buttons = { * - address register : bit [0-2] -> GPIO [47-49] * - data register : bit [0-2] -> GPIO [44-46] * - enable register : GPIO 29 - * + */ + +static int netxbig_v2_gpio_ext_addr[] = { 47, 48, 49 }; +static int netxbig_v2_gpio_ext_data[] = { 44, 45, 46 }; + +static struct netxbig_gpio_ext netxbig_v2_gpio_ext = { + .addr = netxbig_v2_gpio_ext_addr, + .num_addr = ARRAY_SIZE(netxbig_v2_gpio_ext_addr), + .data = netxbig_v2_gpio_ext_data, + .num_data = ARRAY_SIZE(netxbig_v2_gpio_ext_data), + .enable = 29, +}; + +/* * Address register selection: * * addr | register * ---------------------------- * 0 | front LED * 1 | front LED brightness - * 2 | HDD LED brightness - * 3 | HDD1 LED - * 4 | HDD2 LED - * 5 | HDD3 LED - * 6 | HDD4 LED - * 7 | HDD5 LED + * 2 | SATA LED brightness + * 3 | SATA0 LED + * 4 | SATA1 LED + * 5 | SATA2 LED + * 6 | SATA3 LED + * 7 | SATA4 LED * * Data register configuration: * @@ -233,30 +161,107 @@ static struct platform_device netxbig_v2_gpio_buttons = { * 6 | blink blue on=1 sec and red on=1 sec * 7 | blink blue on=0.5 sec and blue off=2.5 sec * - * data | HDD LED mode + * data | SATA LED mode * ------------------------------------------------- - * 0 | fix blue on + * 0 | fix off * 1 | SATA activity blink * 2 | fix red on * 3 | blink blue on=1 sec and blue off=1 sec * 4 | blink red on=1 sec and red off=1 sec * 5 | blink blue on=2.5 sec and red on=0.5 sec * 6 | blink blue on=1 sec and red on=1 sec - * 7 | blink blue on=0.5 sec and blue off=2.5 sec + * 7 | fix blue on */ -/***************************************************************************** - * Timer - ****************************************************************************/ +static int netxbig_v2_red_mled[NETXBIG_LED_MODE_NUM] = { + [NETXBIG_LED_OFF] = 0, + [NETXBIG_LED_ON] = 2, + [NETXBIG_LED_SATA] = NETXBIG_LED_INVALID_MODE, + [NETXBIG_LED_TIMER1] = 4, + [NETXBIG_LED_TIMER2] = NETXBIG_LED_INVALID_MODE, +}; -static void netxbig_v2_timer_init(void) -{ - kirkwood_tclk = 166666667; - orion_time_init(IRQ_KIRKWOOD_BRIDGE, kirkwood_tclk); -} +static int netxbig_v2_blue_pwr_mled[NETXBIG_LED_MODE_NUM] = { + [NETXBIG_LED_OFF] = 0, + [NETXBIG_LED_ON] = 1, + [NETXBIG_LED_SATA] = NETXBIG_LED_INVALID_MODE, + [NETXBIG_LED_TIMER1] = 3, + [NETXBIG_LED_TIMER2] = 7, +}; + +static int netxbig_v2_blue_sata_mled[NETXBIG_LED_MODE_NUM] = { + [NETXBIG_LED_OFF] = 0, + [NETXBIG_LED_ON] = 7, + [NETXBIG_LED_SATA] = 1, + [NETXBIG_LED_TIMER1] = 3, + [NETXBIG_LED_TIMER2] = NETXBIG_LED_INVALID_MODE, +}; + +static struct netxbig_led_timer netxbig_v2_led_timer[] = { + [0] = { + .delay_on = 500, + .delay_off = 500, + .mode = NETXBIG_LED_TIMER1, + }, + [1] = { + .delay_on = 500, + .delay_off = 1000, + .mode = NETXBIG_LED_TIMER2, + }, +}; + +#define NETXBIG_LED(_name, maddr, mval, baddr) \ + { .name = _name, \ + .mode_addr = maddr, \ + .mode_val = mval, \ + .bright_addr = baddr } + +static struct netxbig_led net2big_v2_leds_ctrl[] = { + NETXBIG_LED("net2big-v2:blue:power", 0, netxbig_v2_blue_pwr_mled, 1), + NETXBIG_LED("net2big-v2:red:power", 0, netxbig_v2_red_mled, 1), + NETXBIG_LED("net2big-v2:blue:sata0", 3, netxbig_v2_blue_sata_mled, 2), + NETXBIG_LED("net2big-v2:red:sata0", 3, netxbig_v2_red_mled, 2), + NETXBIG_LED("net2big-v2:blue:sata1", 4, netxbig_v2_blue_sata_mled, 2), + NETXBIG_LED("net2big-v2:red:sata1", 4, netxbig_v2_red_mled, 2), +}; + +static struct netxbig_led_platform_data net2big_v2_leds_data = { + .gpio_ext = &netxbig_v2_gpio_ext, + .timer = netxbig_v2_led_timer, + .num_timer = ARRAY_SIZE(netxbig_v2_led_timer), + .leds = net2big_v2_leds_ctrl, + .num_leds = ARRAY_SIZE(net2big_v2_leds_ctrl), +}; + +static struct netxbig_led net5big_v2_leds_ctrl[] = { + NETXBIG_LED("net5big-v2:blue:power", 0, netxbig_v2_blue_pwr_mled, 1), + NETXBIG_LED("net5big-v2:red:power", 0, netxbig_v2_red_mled, 1), + NETXBIG_LED("net5big-v2:blue:sata0", 3, netxbig_v2_blue_sata_mled, 2), + NETXBIG_LED("net5big-v2:red:sata0", 3, netxbig_v2_red_mled, 2), + NETXBIG_LED("net5big-v2:blue:sata1", 4, netxbig_v2_blue_sata_mled, 2), + NETXBIG_LED("net5big-v2:red:sata1", 4, netxbig_v2_red_mled, 2), + NETXBIG_LED("net5big-v2:blue:sata2", 5, netxbig_v2_blue_sata_mled, 2), + NETXBIG_LED("net5big-v2:red:sata2", 5, netxbig_v2_red_mled, 2), + NETXBIG_LED("net5big-v2:blue:sata3", 6, netxbig_v2_blue_sata_mled, 2), + NETXBIG_LED("net5big-v2:red:sata3", 6, netxbig_v2_red_mled, 2), + NETXBIG_LED("net5big-v2:blue:sata4", 7, netxbig_v2_blue_sata_mled, 2), + NETXBIG_LED("net5big-v2:red:sata5", 7, netxbig_v2_red_mled, 2), +}; -struct sys_timer netxbig_v2_timer = { - .init = netxbig_v2_timer_init, +static struct netxbig_led_platform_data net5big_v2_leds_data = { + .gpio_ext = &netxbig_v2_gpio_ext, + .timer = netxbig_v2_led_timer, + .num_timer = ARRAY_SIZE(netxbig_v2_led_timer), + .leds = net5big_v2_leds_ctrl, + .num_leds = ARRAY_SIZE(net5big_v2_leds_ctrl), +}; + +static struct platform_device netxbig_v2_leds = { + .name = "leds-netxbig", + .id = -1, + .dev = { + .platform_data = &net2big_v2_leds_data, + }, }; /***************************************************************************** @@ -284,18 +289,18 @@ static unsigned int net2big_v2_mpp_config[] __initdata = { MPP24_GPIO, /* USB mode select */ MPP26_GPIO, /* USB device vbus */ MPP28_GPIO, /* USB enable host vbus */ - MPP29_GPIO, /* CPLD extension ALE */ + MPP29_GPIO, /* GPIO extension ALE */ MPP34_GPIO, /* Rear Push button */ MPP35_GPIO, /* Inhibit switch power-off */ MPP36_GPIO, /* SATA HDD1 presence */ MPP37_GPIO, /* SATA HDD2 presence */ MPP40_GPIO, /* eSATA presence */ - MPP44_GPIO, /* CPLD extension (data 0) */ - MPP45_GPIO, /* CPLD extension (data 1) */ - MPP46_GPIO, /* CPLD extension (data 2) */ - MPP47_GPIO, /* CPLD extension (addr 0) */ - MPP48_GPIO, /* CPLD extension (addr 1) */ - MPP49_GPIO, /* CPLD extension (addr 2) */ + MPP44_GPIO, /* GPIO extension (data 0) */ + MPP45_GPIO, /* GPIO extension (data 1) */ + MPP46_GPIO, /* GPIO extension (data 2) */ + MPP47_GPIO, /* GPIO extension (addr 0) */ + MPP48_GPIO, /* GPIO extension (addr 1) */ + MPP49_GPIO, /* GPIO extension (addr 2) */ 0 }; @@ -324,7 +329,7 @@ static unsigned int net5big_v2_mpp_config[] __initdata = { MPP26_GE1_RXD2, MPP27_GE1_RXD3, MPP28_GPIO, /* USB enable host vbus */ - MPP29_GPIO, /* CPLD extension ALE */ + MPP29_GPIO, /* GPIO extension ALE */ MPP30_GE1_RXCTL, MPP31_GE1_RXCLK, MPP32_GE1_TCLKOUT, @@ -339,12 +344,12 @@ static unsigned int net5big_v2_mpp_config[] __initdata = { MPP41_GPIO, /* SATA HDD3 power */ MPP42_GPIO, /* SATA HDD4 power */ MPP43_GPIO, /* SATA HDD5 power */ - MPP44_GPIO, /* CPLD extension (data 0) */ - MPP45_GPIO, /* CPLD extension (data 1) */ - MPP46_GPIO, /* CPLD extension (data 2) */ - MPP47_GPIO, /* CPLD extension (addr 0) */ - MPP48_GPIO, /* CPLD extension (addr 1) */ - MPP49_GPIO, /* CPLD extension (addr 2) */ + MPP44_GPIO, /* GPIO extension (data 0) */ + MPP45_GPIO, /* GPIO extension (data 1) */ + MPP46_GPIO, /* GPIO extension (data 2) */ + MPP47_GPIO, /* GPIO extension (addr 0) */ + MPP48_GPIO, /* GPIO extension (addr 1) */ + MPP49_GPIO, /* GPIO extension (addr 2) */ 0 }; @@ -366,7 +371,10 @@ static void __init netxbig_v2_init(void) else kirkwood_mpp_conf(net5big_v2_mpp_config); - netxbig_v2_sata_power_init(); + if (machine_is_net2big_v2()) + lacie_v2_hdd_power_init(2); + else + lacie_v2_hdd_power_init(5); kirkwood_ehci_init(); kirkwood_ge00_init(&netxbig_v2_ge00_data); @@ -374,13 +382,12 @@ static void __init netxbig_v2_init(void) kirkwood_ge01_init(&netxbig_v2_ge01_data); kirkwood_sata_init(&netxbig_v2_sata_data); kirkwood_uart0_init(); - spi_register_board_info(netxbig_v2_spi_slave_info, - ARRAY_SIZE(netxbig_v2_spi_slave_info)); - kirkwood_spi_init(); - kirkwood_i2c_init(); - i2c_register_board_info(0, netxbig_v2_i2c_info, - ARRAY_SIZE(netxbig_v2_i2c_info)); + lacie_v2_register_flash(); + lacie_v2_register_i2c_devices(); + if (machine_is_net5big_v2()) + netxbig_v2_leds.dev.platform_data = &net5big_v2_leds_data; + platform_device_register(&netxbig_v2_leds); platform_device_register(&netxbig_v2_gpio_buttons); if (gpio_request(NETXBIG_V2_GPIO_POWER_OFF, "power-off") == 0 && @@ -392,24 +399,20 @@ static void __init netxbig_v2_init(void) #ifdef CONFIG_MACH_NET2BIG_V2 MACHINE_START(NET2BIG_V2, "LaCie 2Big Network v2") - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = netxbig_v2_init, .map_io = kirkwood_map_io, .init_irq = kirkwood_init_irq, - .timer = &netxbig_v2_timer, + .timer = &lacie_v2_timer, MACHINE_END #endif #ifdef CONFIG_MACH_NET5BIG_V2 MACHINE_START(NET5BIG_V2, "LaCie 5Big Network v2") - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = netxbig_v2_init, .map_io = kirkwood_map_io, .init_irq = kirkwood_init_irq, - .timer = &netxbig_v2_timer, + .timer = &lacie_v2_timer, MACHINE_END #endif diff --git a/arch/arm/mach-kirkwood/openrd-setup.c b/arch/arm/mach-kirkwood/openrd-setup.c index fd06be6188159d..c9d77fad10ab85 100644 --- a/arch/arm/mach-kirkwood/openrd-setup.c +++ b/arch/arm/mach-kirkwood/openrd-setup.c @@ -16,6 +16,7 @@ #include #include #include +#include #include #include #include @@ -57,7 +58,22 @@ static struct mvsdio_platform_data openrd_mvsdio_data = { }; static unsigned int openrd_mpp_config[] __initdata = { + MPP12_SD_CLK, + MPP13_SD_CMD, + MPP14_SD_D0, + MPP15_SD_D1, + MPP16_SD_D2, + MPP17_SD_D3, + MPP28_GPIO, MPP29_GPIO, + MPP34_GPIO, + 0 +}; + +/* Configure MPP for UART1 */ +static unsigned int openrd_uart1_mpp_config[] __initdata = { + MPP13_UART1_TXD, + MPP14_UART1_RXD, 0 }; @@ -67,6 +83,68 @@ static struct i2c_board_info i2c_board_info[] __initdata = { }, }; +static int __initdata uart1; + +static int __init sd_uart_selection(char *str) +{ + uart1 = -EINVAL; + + /* Default is SD. Change if required, for UART */ + if (!str) + return 0; + + if (!strncmp(str, "232", 3)) { + uart1 = 232; + } else if (!strncmp(str, "485", 3)) { + /* OpenRD-Base doesn't have RS485. Treat is as an + * unknown argument & just have default setting - + * which is SD */ + if (machine_is_openrd_base()) { + uart1 = -ENODEV; + return 1; + } + + uart1 = 485; + } + return 1; +} +/* Parse boot_command_line string kw_openrd_init_uart1=232/485 */ +__setup("kw_openrd_init_uart1=", sd_uart_selection); + +static int __init uart1_mpp_config(void) +{ + kirkwood_mpp_conf(openrd_uart1_mpp_config); + + if (gpio_request(34, "SD_UART1_SEL")) { + printk(KERN_ERR "GPIO request failed for SD/UART1 selection" + ", gpio: 34\n"); + return -EIO; + } + + if (gpio_request(28, "RS232_RS485_SEL")) { + printk(KERN_ERR "GPIO request failed for RS232/RS485 selection" + ", gpio# 28\n"); + gpio_free(34); + return -EIO; + } + + /* Select UART1 + * Pin # 34: 0 => UART1, 1 => SD */ + gpio_direction_output(34, 0); + + /* Select RS232 OR RS485 + * Pin # 28: 0 => RS232, 1 => RS485 */ + if (uart1 == 232) + gpio_direction_output(28, 0); + else + gpio_direction_output(28, 1); + + gpio_free(34); + gpio_free(28); + + return 0; +} + static void __init openrd_init(void) { /* @@ -90,7 +168,6 @@ static void __init openrd_init(void) kirkwood_ge01_init(&openrd_ge01_data); kirkwood_sata_init(&openrd_sata_data); - kirkwood_sdio_init(&openrd_mvsdio_data); kirkwood_i2c_init(); @@ -99,6 +176,28 @@ static void __init openrd_init(void) ARRAY_SIZE(i2c_board_info)); kirkwood_audio_init(); } + + if (uart1 <= 0) { + if (uart1 < 0) + printk(KERN_ERR "Invalid kernel parameter to select " + "UART1. Defaulting to SD. ERROR CODE: %d\n", + uart1); + + /* Select SD + * Pin # 34: 0 => UART1, 1 => SD */ + if (gpio_request(34, "SD_UART1_SEL")) { + printk(KERN_ERR "GPIO request failed for SD/UART1 " + "selection, gpio: 34\n"); + } else { + + gpio_direction_output(34, 1); + gpio_free(34); + kirkwood_sdio_init(&openrd_mvsdio_data); + } + } else { + if (!uart1_mpp_config()) + kirkwood_uart1_init(); + } } static int __init openrd_pci_init(void) @@ -115,8 +214,6 @@ subsys_initcall(openrd_pci_init); #ifdef CONFIG_MACH_OPENRD_BASE MACHINE_START(OPENRD_BASE, "Marvell OpenRD Base Board") /* Maintainer: Dhaval Vasa */ - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = openrd_init, .map_io = kirkwood_map_io, @@ -128,8 +225,6 @@ MACHINE_END #ifdef CONFIG_MACH_OPENRD_CLIENT MACHINE_START(OPENRD_CLIENT, "Marvell OpenRD Client Board") /* Maintainer: Dhaval Vasa */ - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = openrd_init, .map_io = kirkwood_map_io, @@ -141,8 +236,6 @@ MACHINE_END #ifdef CONFIG_MACH_OPENRD_ULTIMATE MACHINE_START(OPENRD_ULTIMATE, "Marvell OpenRD Ultimate Board") /* Maintainer: Dhaval Vasa */ - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = openrd_init, .map_io = kirkwood_map_io, diff --git a/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c b/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c index c34718c2cfe511..0049614cd3245f 100644 --- a/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c +++ b/arch/arm/mach-kirkwood/rd88f6192-nas-setup.c @@ -79,8 +79,6 @@ subsys_initcall(rd88f6192_pci_init); MACHINE_START(RD88F6192_NAS, "Marvell RD-88F6192-NAS Development Board") /* Maintainer: Saeed Bishara */ - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = rd88f6192_init, .map_io = kirkwood_map_io, diff --git a/arch/arm/mach-kirkwood/rd88f6281-setup.c b/arch/arm/mach-kirkwood/rd88f6281-setup.c index 3d1477135e12d8..0998a08cf42d84 100644 --- a/arch/arm/mach-kirkwood/rd88f6281-setup.c +++ b/arch/arm/mach-kirkwood/rd88f6281-setup.c @@ -115,8 +115,6 @@ subsys_initcall(rd88f6281_pci_init); MACHINE_START(RD88F6281, "Marvell RD-88F6281 Reference Board") /* Maintainer: Saeed Bishara */ - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = rd88f6281_init, .map_io = kirkwood_map_io, diff --git a/arch/arm/mach-kirkwood/sheevaplug-setup.c b/arch/arm/mach-kirkwood/sheevaplug-setup.c index a00879d34d5415..d2eec35dfe0f2a 100644 --- a/arch/arm/mach-kirkwood/sheevaplug-setup.c +++ b/arch/arm/mach-kirkwood/sheevaplug-setup.c @@ -131,8 +131,6 @@ static void __init sheevaplug_init(void) #ifdef CONFIG_MACH_SHEEVAPLUG MACHINE_START(SHEEVAPLUG, "Marvell SheevaPlug Reference Board") /* Maintainer: shadi Ammouri */ - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = sheevaplug_init, .map_io = kirkwood_map_io, @@ -143,8 +141,6 @@ MACHINE_END #ifdef CONFIG_MACH_ESATA_SHEEVAPLUG MACHINE_START(ESATA_SHEEVAPLUG, "Marvell eSATA SheevaPlug Reference Board") - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = sheevaplug_init, .map_io = kirkwood_map_io, diff --git a/arch/arm/mach-kirkwood/t5325-setup.c b/arch/arm/mach-kirkwood/t5325-setup.c index d01bf89cedbe79..ce50e61aac9fee 100644 --- a/arch/arm/mach-kirkwood/t5325-setup.c +++ b/arch/arm/mach-kirkwood/t5325-setup.c @@ -184,8 +184,6 @@ subsys_initcall(hp_t5325_pci_init); MACHINE_START(T5325, "HP t5325 Thin Client") /* Maintainer: Martin Michlmayr */ - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = hp_t5325_init, .map_io = kirkwood_map_io, diff --git a/arch/arm/mach-kirkwood/ts219-setup.c b/arch/arm/mach-kirkwood/ts219-setup.c index a5bd7fde04a942..6710bd7773b8b0 100644 --- a/arch/arm/mach-kirkwood/ts219-setup.c +++ b/arch/arm/mach-kirkwood/ts219-setup.c @@ -120,8 +120,6 @@ subsys_initcall(ts219_pci_init); MACHINE_START(TS219, "QNAP TS-119/TS-219") /* Maintainer: Martin Michlmayr */ - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = qnap_ts219_init, .map_io = kirkwood_map_io, diff --git a/arch/arm/mach-kirkwood/ts41x-setup.c b/arch/arm/mach-kirkwood/ts41x-setup.c index 2e14afef07a2ac..8be09a0ce4ac72 100644 --- a/arch/arm/mach-kirkwood/ts41x-setup.c +++ b/arch/arm/mach-kirkwood/ts41x-setup.c @@ -149,8 +149,6 @@ subsys_initcall(ts41x_pci_init); MACHINE_START(TS41X, "QNAP TS-41x") /* Maintainer: Martin Michlmayr */ - .phys_io = KIRKWOOD_REGS_PHYS_BASE, - .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = qnap_ts41x_init, .map_io = kirkwood_map_io, diff --git a/arch/arm/mach-ks8695/board-acs5k.c b/arch/arm/mach-ks8695/board-acs5k.c index 9e3e5a640ad255..3ca4f8e6f54fd1 100644 --- a/arch/arm/mach-ks8695/board-acs5k.c +++ b/arch/arm/mach-ks8695/board-acs5k.c @@ -223,8 +223,6 @@ static void __init acs5k_init(void) MACHINE_START(ACS5K, "Brivo Systems LLC ACS-5000 Master board") /* Maintainer: Simtec Electronics. */ - .phys_io = KS8695_IO_PA, - .io_pg_offst = (KS8695_IO_VA >> 18) & 0xfffc, .boot_params = KS8695_SDRAM_PA + 0x100, .map_io = ks8695_map_io, .init_irq = ks8695_init_irq, diff --git a/arch/arm/mach-ks8695/board-dsm320.c b/arch/arm/mach-ks8695/board-dsm320.c index 521ff0789f398e..ada92b6bed2479 100644 --- a/arch/arm/mach-ks8695/board-dsm320.c +++ b/arch/arm/mach-ks8695/board-dsm320.c @@ -121,8 +121,6 @@ static void __init dsm320_init(void) MACHINE_START(DSM320, "D-Link DSM-320 Wireless Media Player") /* Maintainer: Simtec Electronics. */ - .phys_io = KS8695_IO_PA, - .io_pg_offst = (KS8695_IO_VA >> 18) & 0xfffc, .boot_params = KS8695_SDRAM_PA + 0x100, .map_io = ks8695_map_io, .init_irq = ks8695_init_irq, diff --git a/arch/arm/mach-ks8695/board-micrel.c b/arch/arm/mach-ks8695/board-micrel.c index 8ceaf5ac6e2ca4..c7ad09bd6ea21a 100644 --- a/arch/arm/mach-ks8695/board-micrel.c +++ b/arch/arm/mach-ks8695/board-micrel.c @@ -53,8 +53,6 @@ static void __init micrel_init(void) MACHINE_START(KS8695, "KS8695 Centaur Development Board") /* Maintainer: Micrel Semiconductor Inc. */ - .phys_io = KS8695_IO_PA, - .io_pg_offst = (KS8695_IO_VA >> 18) & 0xfffc, .boot_params = KS8695_SDRAM_PA + 0x100, .map_io = ks8695_map_io, .init_irq = ks8695_init_irq, diff --git a/arch/arm/mach-ks8695/include/mach/debug-macro.S b/arch/arm/mach-ks8695/include/mach/debug-macro.S index cf2095da2372cd..bf516adf19250d 100644 --- a/arch/arm/mach-ks8695/include/mach/debug-macro.S +++ b/arch/arm/mach-ks8695/include/mach/debug-macro.S @@ -14,11 +14,9 @@ #include #include - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - ldreq \rx, =KS8695_UART_PA @ physical base address - ldrne \rx, =KS8695_UART_VA @ virtual base address + .macro addruart, rp, rv + ldr \rp, =KS8695_UART_PA @ physical base address + ldr \rv, =KS8695_UART_VA @ virtual base address .endm .macro senduart, rd, rx diff --git a/arch/arm/mach-l7200/include/mach/debug-macro.S b/arch/arm/mach-l7200/include/mach/debug-macro.S new file mode 100644 index 00000000000000..b0a2db77d39267 --- /dev/null +++ b/arch/arm/mach-l7200/include/mach/debug-macro.S @@ -0,0 +1,38 @@ +/* arch/arm/mach-l7200/include/mach/debug-macro.S + * + * Debugging macro include header + * + * Copyright (C) 1994-1999 Russell King + * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * +*/ + + .equ io_virt, IO_BASE + .equ io_phys, IO_START + + .macro addruart, rp, rv + mov \rp, #0x00044000 @ UART1 +@ mov \rp, #0x00045000 @ UART2 + add \rv, \rp, #io_virt @ virtual address + add \rp, \rp, #io_phys @ physical base address + .endm + + .macro senduart,rd,rx + str \rd, [\rx, #0x0] @ UARTDR + .endm + + .macro waituart,rd,rx +1001: ldr \rd, [\rx, #0x18] @ UARTFLG + tst \rd, #1 << 5 @ UARTFLGUTXFF - 1 when full + bne 1001b + .endm + + .macro busyuart,rd,rx +1001: ldr \rd, [\rx, #0x18] @ UARTFLG + tst \rd, #1 << 3 @ UARTFLGUBUSY - 1 when busy + bne 1001b + .endm diff --git a/arch/arm/mach-lh7a40x/arch-kev7a400.c b/arch/arm/mach-lh7a40x/arch-kev7a400.c index 3d7bd50b9095ba..9088c16662e808 100644 --- a/arch/arm/mach-lh7a40x/arch-kev7a400.c +++ b/arch/arm/mach-lh7a40x/arch-kev7a400.c @@ -111,8 +111,6 @@ void __init lh7a40x_init_board_irq (void) MACHINE_START (KEV7A400, "Sharp KEV7a400") /* Maintainer: Marc Singer */ - .phys_io = 0x80000000, - .io_pg_offst = ((io_p2v (0x80000000))>>18) & 0xfffc, .boot_params = 0xc0000100, .map_io = kev7a400_map_io, .init_irq = lh7a400_init_irq, diff --git a/arch/arm/mach-lh7a40x/arch-lpd7a40x.c b/arch/arm/mach-lh7a40x/arch-lpd7a40x.c index cb15e5d3212026..7315a569aea121 100644 --- a/arch/arm/mach-lh7a40x/arch-lpd7a40x.c +++ b/arch/arm/mach-lh7a40x/arch-lpd7a40x.c @@ -398,8 +398,6 @@ lpd7a40x_map_io(void) MACHINE_START (LPD7A400, "Logic Product Development LPD7A400-10") /* Maintainer: Marc Singer */ - .phys_io = 0x80000000, - .io_pg_offst = ((io_p2v (0x80000000))>>18) & 0xfffc, .boot_params = 0xc0000100, .map_io = lpd7a40x_map_io, .init_irq = lh7a400_init_irq, @@ -413,8 +411,6 @@ MACHINE_END MACHINE_START (LPD7A404, "Logic Product Development LPD7A404-10") /* Maintainer: Marc Singer */ - .phys_io = 0x80000000, - .io_pg_offst = ((io_p2v (0x80000000))>>18) & 0xfffc, .boot_params = 0xc0000100, .map_io = lpd7a40x_map_io, .init_irq = lh7a404_init_irq, diff --git a/arch/arm/mach-lh7a40x/include/mach/debug-macro.S b/arch/arm/mach-lh7a40x/include/mach/debug-macro.S index c0dcbbba22ba6f..cff33625276faa 100644 --- a/arch/arm/mach-lh7a40x/include/mach/debug-macro.S +++ b/arch/arm/mach-lh7a40x/include/mach/debug-macro.S @@ -14,12 +14,10 @@ @ It is not known if this will be appropriate for every 40x @ board. - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - mov \rx, #0x00000700 @ offset from base - orreq \rx, \rx, #0x80000000 @ physical base - orrne \rx, \rx, #0xf8000000 @ virtual base + .macro addruart, rp, rv + mov \rp, #0x00000700 @ offset from base + orr \rv, \rp, #0xf8000000 @ virtual base + orr \rp, \rp, #0x80000000 @ physical base .endm .macro senduart,rd,rx diff --git a/arch/arm/mach-loki/include/mach/debug-macro.S b/arch/arm/mach-loki/include/mach/debug-macro.S index 3136c913a92c2c..cc90d99ac76ce8 100644 --- a/arch/arm/mach-loki/include/mach/debug-macro.S +++ b/arch/arm/mach-loki/include/mach/debug-macro.S @@ -8,12 +8,11 @@ #include - .macro addruart, rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - ldreq \rx, =LOKI_REGS_PHYS_BASE - ldrne \rx, =LOKI_REGS_VIRT_BASE - orr \rx, \rx, #0x00012000 + .macro addruart, rp, rv + ldr \rp, =LOKI_REGS_PHYS_BASE + ldr \rv, =LOKI_REGS_VIRT_BASE + orr \rp, \rp, #0x00012000 + orr \rv, \rv, #0x00012000 .endm #define UART_SHIFT 2 diff --git a/arch/arm/mach-loki/lb88rc8480-setup.c b/arch/arm/mach-loki/lb88rc8480-setup.c index 85f9c1296aa026..a1e75e7fc50092 100644 --- a/arch/arm/mach-loki/lb88rc8480-setup.c +++ b/arch/arm/mach-loki/lb88rc8480-setup.c @@ -90,8 +90,6 @@ static void __init lb88rc8480_init(void) MACHINE_START(LB88RC8480, "Marvell LB88RC8480 Development Board") /* Maintainer: Ke Wei */ - .phys_io = LOKI_REGS_PHYS_BASE, - .io_pg_offst = ((LOKI_REGS_VIRT_BASE) >> 18) & 0xfffc, .boot_params = 0x00000100, .init_machine = lb88rc8480_init, .map_io = loki_map_io, diff --git a/arch/arm/mach-lpc32xx/include/mach/debug-macro.S b/arch/arm/mach-lpc32xx/include/mach/debug-macro.S index 621744d6b15205..629e744aeb9e98 100644 --- a/arch/arm/mach-lpc32xx/include/mach/debug-macro.S +++ b/arch/arm/mach-lpc32xx/include/mach/debug-macro.S @@ -20,11 +20,9 @@ * Debug output is hardcoded to standard UART 5 */ - .macro addruart,rx, tmp - mrc p15, 0, \rx, c1, c0 - tst \rx, #1 @ MMU enabled? - ldreq \rx, =0x40090000 - ldrne \rx, =0xF4090000 + .macro addruart, rp, rv + ldreq \rp, =0x40090000 + ldrne \rv, =0xF4090000 .endm #define UART_SHIFT 2 diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c index 0c936cf5675aa7..7993b096778e1f 100644 --- a/arch/arm/mach-lpc32xx/phy3250.c +++ b/arch/arm/mach-lpc32xx/phy3250.c @@ -382,8 +382,6 @@ arch_initcall(lpc32xx_display_uid); MACHINE_START(PHY3250, "Phytec 3250 board with the LPC3250 Microcontroller") /* Maintainer: Kevin Wells, NXP Semiconductors */ - .phys_io = LPC32XX_UART5_BASE, - .io_pg_offst = ((IO_ADDRESS(LPC32XX_UART5_BASE))>>18) & 0xfffc, .boot_params = 0x80000100, .map_io = lpc32xx_map_io, .init_irq = lpc32xx_init_irq, diff --git a/arch/arm/mach-mmp/Kconfig b/arch/arm/mach-mmp/Kconfig index 6ab843eaa35b50..0711d3b620ad22 100644 --- a/arch/arm/mach-mmp/Kconfig +++ b/arch/arm/mach-mmp/Kconfig @@ -57,6 +57,13 @@ config MACH_MARVELL_JASPER PXA910-based development board. Since MMP2 is compatible to ARMv6 architecture. +config MACH_TETON_BGA + bool "Marvell's PXA168 Teton BGA Development Board" + select CPU_PXA168 + help + Say 'Y' here if you want to support the Marvell PXA168-based + Teton BGA Development Board. + endmenu config CPU_PXA168 diff --git a/arch/arm/mach-mmp/Makefile b/arch/arm/mach-mmp/Makefile index 8b66d06739c4d9..751cdbf733c852 100644 --- a/arch/arm/mach-mmp/Makefile +++ b/arch/arm/mach-mmp/Makefile @@ -17,3 +17,4 @@ obj-$(CONFIG_MACH_TAVOREVB) += tavorevb.o obj-$(CONFIG_MACH_TTC_DKB) += ttc_dkb.o obj-$(CONFIG_MACH_FLINT) += flint.o obj-$(CONFIG_MACH_MARVELL_JASPER) += jasper.o +obj-$(CONFIG_MACH_TETON_BGA) += teton_bga.o diff --git a/arch/arm/mach-mmp/aspenite.c b/arch/arm/mach-mmp/aspenite.c index 0629394a5fb9ad..06b5fa853c9325 100644 --- a/arch/arm/mach-mmp/aspenite.c +++ b/arch/arm/mach-mmp/aspenite.c @@ -16,6 +16,7 @@ #include #include #include +#include #include #include @@ -23,6 +24,9 @@ #include #include #include +#include